The LEON interrupt controller has one single mask register for all
IRQs per CPU, even though the genirq layer protects us from accessing
the same IRQ at the same time other IRQs share the same mask register
and may thus interfere. Some other IRQ controllers has a mask register
or similar per IRQ instead which makes spinlocks unncessary.
Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The conversion of sparc32 to genirq is based on original work done
by David S. Miller.
Daniel Hellstrom has helped in the conversion and implemented
the shutdowm functionality.
Marcel van Nies <morcles@gmail.com> has tested this on Sparc Station 20

Test status:
sun4c      - not tested
sun4m,pci  - not tested
sun4m,sbus - tested (Sparc Classic, Sparc Station 5, Sparc Station 20)
sun4d      - not tested
leon       - tested on various combinations of leon boards,
             including SMP variants

generic
   Introduce use of GENERIC_HARDIRQS and GENERIC_IRQ_SHOW
   Allocate 64 IRQs - which is enough even for SS2000
   Use a table of irq_bucket to maintain uses IRQs
      irq_bucket is also used to chain several irq's that
      must be called when the same intrrupt is asserted
   Use irq_link to link a interrupt source to the irq
   All plafforms must now supply their own build_device_irq method
   handler_irq rewriten to use generic irq support

floppy
   Read FLOPPY_IRQ from platform device
   Use generic request_irq to register the floppy interrupt
   Rewrote sparc_floppy_irq to use the generic irq support

pcic:
   Introduce irq_chip
   Store mask in chip_data for use in mask/unmask functions
   Add build_device_irq for pcic
   Use pcic_build_device_irq in pci_time_init
   allocate virtual irqs in pcic_fill_irq

sun4c:
   Introduce irq_chip
   Store mask in chip_data for use in mask/unmask functions
   Add build_device_irq for sun4c
   Use sun4c_build_device_irq in sun4c_init_timers

sun4m:
   Introduce irq_chip
   Introduce dedicated mask/unmask methods
   Introduce sun4m_handler_data that allow easy access to necessary
     data in the mask/unmask functions
   Add a helper method to enable profile_timer (used from smp)
   Added sun4m_build_device_irq
   Use sun4m_build_device_irq in sun4m_init_timers

   TODO:
      There is no replacement for smp_rotate that always scheduled
      next CPU as interrupt target upon an interrupt

sun4d:
   Introduce irq_chip
   Introduce dedicated mask/unmask methods
   Introduce sun4d_handler_data that allow easy access to
   necessary data in mask/unmask fuctions
   Rewrote sun4d_handler_irq to use generic irq support

   TODO:
      The original implmentation of enable/disable had:

          if (irq < NR_IRQS)
               return;

      The new implmentation does not distingush between SBUS and cpu
      interrupts.
      I am no sure what is right here. I assume we need to do
      something for the cpu interrupts.

      I have not succeeded booting my sun4d box (with or without this patch)
      and my understanding of this platfrom is limited.
      So I would be a bit suprised if this works.

leon:
   Introduce irq_chip
   Store mask in chip_data for use in mask/unmask functions
   Add build_device_irq for leon
   Use leon_build_device_irq in leon_init_timers
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Acked-by: NDaniel Hellstrom <daniel@gaisler.com>
Tested-by: NDaniel Hellstrom <daniel@gaisler.com>
Tested-by: NMarcel van Nies <morcles@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the ifdeffery to a header file to make the logic more
obvious where we decide between PCI or SBUS init
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new name reflects the actual usage much better.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

We have to pass task_struct of previous process to function
schedule_tail(). Currently in ret_from_fork previous thread_info
is passed:

switch_to: mov %g6, %g3 /* previous thread_info in g6 */

ret_from_fork: call    schedule_tail
                mov    %g3, %o0 /* previous thread_info is passed */

void schedule_tail(struct task_struct *prev);
Signed-off-by: NTkhai Kirill <tkhai@yandex.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix all of the problems spotted by CONFIG_DEBUG_SECTION_MISMATCH under
arch/sparc during a 64-bit defconfig build.

They fall into two categorites:

1) of_device_id is marked as __initdata, and we can never do this
   since these objects sit in the device core data structures way
   past boot.  So even if a driver will never be reloaded, we have
   to keep the device ID table around.

   Mark such cases const instead.

2) The bootmem alloc/free handling code in mdesc.c was not fully
   marked __init as it should be, thus generating a reference
   to free_bootmem_late() (which is __init) from non-__init code.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: sparclinux@vger.kernel.org

Scripted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: sparclinux@vger.kernel.org

Use the proper wrapper functions.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: sparclinux@vger.kernel.org

Make use of the new features in genirq:

1) Set the chip flag IRCHIP_EOI_IF_HANDLED, which ensures in the
   core code that irq_eoi() is only called when the interrupt was
   handled. That removes the extra status check in the callback.

2) Use the preflow handler, which is called from the fasteoi core code
   before the device handler. That avoids another status check and the
   open coded handler redirection.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: sparclinux@vger.kernel.org

During the preparation for testing the recent changes made to the SUN4D
specific code in the kernel by Sam Ravnborg the following was discovered:

Since the removal of of_platform_bus_type (commit: eca39301 )
multiboard SUN4Ds have not been able to boot. The kernel crashes due to a
zero-pointer error encountered when registering multiple M48T59 RTCs
(There is one on each board).

A patch for the was previously submitted, but the problem was not a
serious at that time, as it would only generate warnings. Now the kernel
will crash and stop executing before the serial console has been started.
(Crash output can be viewed by using the -p boot flag)
Signed-off-by: NKjetil Oftedal <oftedal@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Grab the pre-computed resource and map using of_ioremap().
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similarly to irq_of_parse_and_map(), find the platform_device
object and return the pre-computed resource.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gas used to accept (and ignore?) .size directives which referred to
undefined symbols, as this does.  In binutils 2.21 these are treated
as errors.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most of the warnings emitted (we fail arch/sparc file
builds with -Werror) were legitimate but harmless, however
one case (n2_pcr_write) was a genuine bug.

Based almost entirely upon a patch by Sam Ravnborg.
Reported-by: NDennis Gilmore <dennis@ausil.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

entry.S access percpu + global data defined in
sun4m_irq.c - so move the types to irq.h.
This makes sparse happy and allow us to utilize
asm-offsets later.

Also updated a few comments in the sun4m_irq.c file.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

build_device_irq() is used to encapsulate the plaform
specific details when we build an irq.
For now the default is a simple 1:1 but sun4d differs.
This patch refactors functionality - but does not change
the existing functionality.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sparc_irq_config is used to hold the platform specific irq setup.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a few includes back required to build with floppy enabled
Fix declaration of trapbase_cpu* so it is now consistent
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This converts the sparc clocksources to use clocksource_register_hz/khz
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A recent patch to the x86 randomization code caused me to take
a quick look at what we do on sparc64, and in doing so I noticed
that we sometimes calculate a non-page-aligned randomization value
and stick it into mmap_base.

I also noticed that since I copied the logic over from PowerPC,
the powerpc code has tweaked the randomization ranges in ways that
would benefit us as well.

For one thing, we should allow up to at least 8MB of randomization
otherwise huge-page regions when HPAGE_SIZE is 4MB never randomize
at all.

And on the 64-bit side we were using up to 4GB.  Tone it down to
1GB as 4GB can result in a lot of address space wastage.

Finally, make sure all computations are unsigned.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- drop filename in file header
- drop unused includes
- add KERN_* to printk
- fix spaces => tabs
- add spaces after reserved words
- drop all externs, they are now in header files
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This looked like a bug to me.
Add a comment so next reader is hopefully less confused.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The preprocessor symbol was not defined and the code
was therefore not in use.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- drop filename in file header
- drop unused includes
- add description of sun4d interrupts (from davem)
- add KERN_* to printk
- fix spaces => tabs
- add spaces after reserved words
- fix indent of a whole code block in smp4d_boot_one_cpu()
  Note: two printk() was updated from debug to KERN_INFO in this code block
- drop all externs, they are now in header files

This is partly based on a patch from: David Miller <davem@davemloft.net>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- drop filename in file header
- drop unused includes
- add description of sun4m interrupts (from davem)
- add KERN_* to printk
- fix spaces => tabs
- add spaces after reserved words
- drop all externs, they are now in header files

This is partly based on a patch from: David Miller <davem@davemloft.net>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- drop filename in header
- drop unused includes
- add description of sun4c interrupts (from davem)
- add spaces after reserved words

This is partly based on a patch from: David Miller <davem@davemloft.net>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for cleaning up a number of files add
declarations for irq and smp related data/functions to
the relevant headers.

This showed that the extern declaration of cputypval differed
in the two files where it was used.
As cputypval is defined like this:

cputypval:
        .asciz "sun4c"

the correct representation is a char array.
Fix users to use the new declaration.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The two methods included in tick14.c was nop because
the static variable linux_lvl14 was always NULL.

So remove the file and callers.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The way a LEON is powered down is implemented differently depending
on CHIP type. The AMBA Plug&Play system ID tells revision of GRLIB
and CHIP.

This is for example needed by the GR-LEON4-ITX board and the UT699.

Previously the power down support for LEON was limited to SMP, now
both SMP and UP systems use the instruction.
Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The generic irq support uses the term 'irq' for the
allocated irq number.
Fix it so sparc64 use the same term for an irq as the
generic irq support does.
For a naive reader this is less confusing.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The generic irq support uses the term 'irq' for the
allocated irq number.
Fix it so sparc64 use the same term for an irq as the
generic irq support does.
For a naive reader this is less confusing.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop all uses of deprecated genirq features.

The irq_set_affinity() call got a third paramter 'force'
which is unused.
For now genirq does not use this paramter and it is
ignored by sparc.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Josip Rodin <joy@entuzijast.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

{get,set}_irq_data uses the member "handler_data" in irq_data
which fits the naem of the datatype.
The change has no functional impact
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation of moving to use irq_data.handler_data rename
all pointers to irq_handler_data "handler_data".
This will also prevent name clash when we introduce the
new irq methods.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The generic irq support uses "irq" to identify the
virtual irq number. To avoid confusion rename the
argument to handler_irq() to pil to match the
name of the parameter in the PCR register.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>