The camera may in some conditions incorrectly determine the exposure,
and a manual automatic exposure correction may be needed. This patch
adds V4L2_CID_AUTO_EXPOSURE_BIAS control which allows to add some
offset in the automatic exposure control loop, to compensate for
frame under- or over-exposure.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds v4l2_ctrl_new_int_menu() helper function which can be used
in drivers for creating standard integer menu control with driver-specific
menu item list. It is similar to v4l2_ctrl_new_std_menu(), except it doesn't
have a mask parameter and an additional qmenu parameter allows passing
an array of signed 64-bit integers as the menu item list.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Tested-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds definition of additional color effects:

 - V4L2_COLORFX_AQUA,
 - V4L2_COLORFX_ART_FREEZE,
 - V4L2_COLORFX_SILHOUETTE,
 - V4L2_COLORFX_SOLARIZATION,
 - V4L2_COLORFX_ANTIQUE,
 - V4L2_COLORFX_SET_CBCR.

The new V4L2_COLORFX_CBCR control is added to allow setting
the fixed Cb, Cr values that replace chroma Cb/Cr coefficients
in case of V4L2_COLORFX_SET_CBCR effect.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The radio-si470x-usb driver supported both autosuspend and it stopped the
radio the moment the last user of the radio device closed it. However, that
was very confusing since if you play the audio from the device (e.g. through
arecord -D ... | aplay) then no sound would play unless you had the radio
device open at the same time, even though there is no need to do anything
with that node.

On the other hand, the actual suspend/resume functions didn't do anything,
which would fail if you *did* have the radio node open at that time.

So:

- remove autosuspend (bad idea in general for USB radio devices)
- move the start/stop out of the open/release functions into the resume/suspend
  functions.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There is no need to report an error in the log, you are already returning
that error to userspace after all.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This cleans up the code and si470x now uses the proper v4l2 frameworks
and passes most of the v4l2-compliance tests.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This fixes the following warning:

In file included from drivers/media/video/v4l2-subdev.c:29:
include/media/v4l2-ctrls.h:501: warning: 'struct file' declared inside
parameter list
include/media/v4l2-ctrls.h:501: warning: its scope is only this
definition or declaration, which is probably not what you want
include/media/v4l2-ctrls.h:509: warning: 'struct file' declared inside
parameter list
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The driver uses the ctrl value passed in as a bool to determine whether
to enable auto-exposure, but the auto-exposure setting is defined as an
enum where AUTO has a value of 0 and MANUAL has a value of 1. This leads
to a reversed logic where if you send in AUTO, it actually sets manual
exposure and vice-versa.
Signed-off-by: NKartik Mohta <kartikmohta@gmail.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix the following compilation failure:

linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop':
linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop'
linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format':
linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format'
linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe':
linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove':
linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity'
make[4]: *** [drivers/media/video/mt9m032.o] Error 1

by adding a dependency on VIDEO_V4L2_SUBDEV_API.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix a copy-paste typo and a nested locking function call in mt9m032.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add four new controls to configure black level compensation (BLC):

- V4L2_CID_BLC_AUTO selects between manual and auto BLC
- V4L2_CID_BLC_TARGET_LEVEL sets the target level for auto BLC
- V4L2_CID_BLC_ANALOG_OFFSET sets the analog offset for manual BLC
- V4L2_CID_BLC_DIGITAL_OFFSET sets the digital offset for manual BLC
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the GPIO from the sensor driver instead of calling back to board
code.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of passing a color/monochrome flag through platform data, rely
on the I2C device name to identify the chip model.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add all known reference design USB IDs.
Rename two earlier reference design USB IDs.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

We can use tuner ID instead of HW not supported flag.
Lesser code is better code.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixes most problems when having more than one device connected
as demod and tuner configurations are not shared.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

af9033: implement read_ber and read_ucblocks functions. Version 2 of patch that
reflects my findings on the behaviour of abort_cnt, err_cnt and bit_cnt:

- bit_cnt is always 0x2710 (10000)
- abort_cnt is between 0 and 0x2710
- err_cnt is between 0 and 640000 (= 0x2710 * 8 * 8)

in the current implementation BER is calculated as the number of bit errors per
processed bits, ignoring those bits that are already discarded and counted in
abort_cnt, i.e. UCBLOCKS.
Signed-off-by: NHans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Not used anymore since new firmware downloader. I forget to remove
those earlier when changed firmware downloader.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix USB buffer len to maximum possible.
Various log writing fixes, remove extra new lines and excessive
type casts. Rename and type change some variables.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When setting TRY crop on the sub-device the mutex was erroneously acquired
rather than released on exit path. This bug is present in kernels starting
from v3.2.

Cc: stable@vger.kernel.org
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Move drivers/input/fixp-arith.h to include/linux so that the functions
defined there can be used by other subsystems, for instance some video
devices ISPs can control the output HUE value by setting registers for
sin(HUE) and cos(HUE).
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Also merge the "COLORS" control into it as it was V4L2_CID_SATURATION
anyway.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Enabling vflip leads to a much better image, with vflip disabled the
image looks washed out as if there is a too high brightness setting.

Since we don't know how to lower the brightness setting when not
vflipping, simply always vflip and tell userspace to flip the image back,
resulting in a much better (less washed out) image.

Since the image is now no longer too bright, also modify the luminance
level the auto-gain algorithm aims for.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Our init sequence was not setting the register page to point to bank 1
before setting what should be the control reg. This causes the camera to
sometimes have its LED on after init. First selecting register bank 1,
rather then assuming the current register bank is bank 1, fixes this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Now that the pac207 driver has been converted to the control framework, there
are no remaining users.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The pac207's exposure control is a clock-divider, so it goes with quite
big steps. So lets use an autogain algorithm optimised for that.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

We intend to eventually port all sub-drivers to the control-framework. At
which point it will make more sense to have the ctrl_handler in gspca_dev
then to have it in the subdrivers. Lets move it there now, to avoid a lot
of work to move it later.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Now that stv06xx is using the control framework it is no longer necessary
to have a (non const) copy of sd_desc inside the sd specific data struct.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

HdG:
1) Let the gspca-core cleanup the controls on control-init error, like
with the other converted sub drivers
2) Note this also fixes a bug in the hdcs1020 support which was wrongly
reporting an exposure range of 0-65535, even though the effective range was
only 0-255
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

HdG: Small fix: don't register some controls for sensors which don't
have an implementation for them.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>