... so it could fall back to normal numa and we'd reduce the impact of the
NUMAQ subarch.

NUMAQ depends on GENERICARCH
also decouple genericarch numa from acpi.
also make it fall back to bigsmp if apicid > 8.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

make mptable to be consistent with acpi routing, so we could:

1. kexec kernel with acpi=off
2. work around BIOSes where acpi routing is working, but mptable is
   not right, so can use kernel/kexec to start other OSes that don't have
   good acpi support.

command line: update_mptable
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

acpi_device_dir() is NULL until all files are createst, so everyting is
created in straight in /proc/ and creation code warns.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

acpi_processor_idle and "idle=" boot parameter interaction is broken.
The problem is that, at boot time acpi driver is checking for "idle=" boot
option and not registering the acpi idle handler. But, when there is a CST
changed callback (typically when switching AC <-> battery or suspend-resume)
there are no checks for boot_option_idle_override and acpi idle handler tries
to get installed with nasty side effects.

With CPU_IDLE configured this issue causes results in a nasty oops on CST
change callback and without CPU_IDLE there is no oops, but boot option
of "idle=" gets ignored and acpi idle handler gets installed.

Change the behavior to not do anything in acpi idle handler when there is a
"idle=" boot option.

Note that the problem is only there when "idle=" boot option is used.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Legacy HP ia64 platforms currently cannot provide
/proc/cpuinfo/physical_id due to legacy SAL/PAL implementations.
However, that physical topology information can be obtained
via ACPI.

Provide an interface that gives ACPI one last chance to provide
physical_id for these legacy platforms. This logic only comes
into play iff:

- ACPI actually provides slot information for the CPU
- we lack a valid socket_id

Otherwise, we don't do anything.

Since x86 uses the ACPI processor driver as well, we provide a nop
stub function for arch_fix_phys_package_id() in asm-x86/topology.h
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.

Add correct ->owner to proc_fops to fix reading/module unloading race.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

POST and DOS are supposed to be writable but permissions
did not allow it.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Have acpi_video_device_add_fs() and acpi_video_bus_add_fs()
properly unwind proc creation after error.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

this is a cleanup, not a change to function.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

... as they are platform_suspend_ops after all.

cosmetic re-name only, no functional change.
Signed-off-by: NLen Brown <len.brown@intel.com>

We should check *resource != NULL rather than resource != NULL, which will be
always true.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Acked-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

This patch #if 0's the unused eject_removable_drive().
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

acpi_ev_disable_gpe() has an optimization where it doesn't disable
a GPE that it "doesn't have to".  Unfortunately, it can get tricked
by AML that scribbles on register state behind its back.  So when asked
to disable a GPE, simply do it -- a redundant register write
in the common case is a fair price to pay to be bomb-proof
for the rare cases.

http://bugzilla.kernel.org/show_bug.cgi?id=6217Signed-off-by: NDamián Viano <des@debian.org>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fix the problem that thermal_get_temp returns the cached value,
which causes the temperature in generic thermal never updates.
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

thermal_cooling_device_register used to return NULL if THERMAL is "n".
As the ACPI fan, processor and video drivers SELECT the generic
thermal in PATCH 01, this is not a problem any more.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Update the documentation for the thermal driver hwmon sys I/F.

Change the ACPI thermal zone type to be consistent with hwmon.
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add a new callback so that the generic thermal can get
the critical trip point info of a thermal zone,
which is needed for building the tempX_crit hwmon sysfs attribute.
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Build the generic thermal driver as module "thermal_sys".

Make ACPI thermal, video, processor and fan SELECT the generic
thermal driver, as these drivers rely on it to build the sysfs I/F.
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Flush kacpi_notify_wq before notify handler is removed,
this can fix a bug which the deferred notify handler is executed
after the notify_handler has already been removed.
http://bugzilla.kernel.org/show_bug.cgi?id=9772Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Change cpufreq tables from arrays to per_cpu variables in
drivers/acpi/processor_thermal.c

Based on git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git

Cc: Len Brown <len.brown@intel.com>
Signed-off-by: NMike Travis <travis@sgi.com>
Signed-off-by: NDave Jones <davej@codemonkey.org.uk>

drivers/acpi/thermal.c: In function 'acpi_thermal_init':
drivers/acpi/thermal.c:1794: error: 'thermal_dmi_table' undeclared (first use in this function)
drivers/acpi/thermal.c:1794: error: (Each undeclared identifier is reported only once
drivers/acpi/thermal.c:1794: error: for each function it appears in.)
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

OK, so 25-mm1 gave a lockdep error which made me look into this.

The first thing that I noticed was the horrible mess; the second thing I
saw was hacks like: 71e93d15

The problem is that arch idle routines are somewhat inconsitent with
their IRQ state handling and instead of fixing _that_, we go paper over
the problem.

So the thing I've tried to do is set a standard for idle routines and
fix them all up to adhere to that. So the rules are:

  idle routines are entered with IRQs disabled
  idle routines will exit with IRQs enabled

Nearly all already did this in one form or another.

Merge the 32 and 64 bit bits so they no longer have different bugs.

As for the actual lockdep warning; __sti_mwait() did a plainly un-annotated
irq-enable.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This path adds validation of the MMCONFIG table against the ACPI reserved
motherboard resources.  If the MMCONFIG table is found to be reserved in
ACPI, we don't bother checking the E820 table.  The PCI Express firmware
spec apparently tells BIOS developers that reservation in ACPI is required
and E820 reservation is optional, so checking against ACPI first makes
sense.  Many BIOSes don't reserve the MMCONFIG region in E820 even though
it is perfectly functional, the existing check needlessly disables MMCONFIG
in these cases.

In order to do this, MMCONFIG setup has been split into two phases.  If PCI
configuration type 1 is not available then MMCONFIG is enabled early as
before.  Otherwise, it is enabled later after the ACPI interpreter is
enabled, since we need to be able to execute control methods in order to
check the ACPI reserved resources.  Presently this is just triggered off
the end of ACPI interpreter initialization.

There are a few other behavioral changes here:

- Validate all MMCONFIG configurations provided, not just the first one.

- Validate the entire required length of each configuration according to
  the provided ending bus number is reserved, not just the minimum required
  allocation.

- Validate that the area is reserved even if we read it from the chipset
  directly and not from the MCFG table.  This catches the case where the
  BIOS didn't set the location properly in the chipset and has mapped it
  over other things it shouldn't have.

This also cleans up the MMCONFIG initialization functions so that they
simply do nothing if MMCONFIG is not compiled in.

Based on an original patch by Rajesh Shah from Intel.

[akpm@linux-foundation.org: many fixes and cleanups]
Signed-off-by: NRobert Hancock <hancockr@shaw.ca>
Signed-off-by: NAndi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NAndi Kleen <ak@suse.de>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Patch to fix huge number of wakeups reported due to recent changes in
processor_idle.c. The problem was that the entry_method determination was
broken due to one of the recent commits (bc71bec9) causing
C1 entry to not to go to halt.

http://lkml.org/lkml/2008/3/22/124Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

GPE could try to access EC region, so should not be enabled before
EC is installed

http://bugzilla.kernel.org/show_bug.cgi?id=9916Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Fixed a problem with the CreateField, CreateXXXField (Bit, Byte,
Word, Dword, Qword), Field, BankField, and IndexField operators
when invoked from inside an executing control method. In this case,
these operators created namespace nodes that were incorrectly
left marked as permanent nodes instead of temporary nodes. This
could cause a problem if there is race condition between an
exiting control method and a running namespace walk. (Reported
by Linn Crosetto). Fixed a problem where the CreateField and
CreateXXXField operators would incorrectly allow duplicate names
(the name of the field) with no exception generated.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Implemented several changes for Notify handling: Added support
for new Notify values (ACPI 2.0+) and improved the Notify debug
output. Notify on PowerResource objects is no longer allowed,
as per the ACPI specification.
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fixed a couple of size calculation issues with the variable-length
Start Dependent resource descriptor.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Implemented several improvements for the output of the ASL "Debug"
object to clarify and keep all data for a given object on one
output line.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

All Reference Objects returned via the AcpiEvaluteObject interface
are now marked as type "REFERENCE" instead of "ANY". The type ANY
is now reservered for NULL objects - either NULL package elements
or unresolved named references.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fixed problem where NULL package elements were not returned to
the AcpiEvaluateObject interface correctly. Instead of returning a
NULL ACPI_OBJECT package element, the element was simply ignored,
potentially causing a buffer overflow and/or confusing the caller
who expected a fixed number of elements.

http://bugzilla.kernel.org/show_bug.cgi?id=10132Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fixed a problem where an extraneous debug message was produced for
package objects (when debugging enabled). The message "Package
List length larger than NumElements count" is now produced in
the correct case, and is also an error message rather than a
debug message. Added a debug message for the opposite case, where
NumElements is larger than the Package List, and the package has
been padded out with NULL elements.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fixed a problem where buffer and package objects passed as
arguments to a control method via the external AcpiEvaluateObject
interface could cause an AE_AML_INTERNAL exception depending on the
order and type of operators executed by the target control method.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fixed a problem where a CopyObject to RegionField, BankField, and
IndexField objects did not perform an implicit conversion as it
should. These types must retain their initial type permanently as
per the ACPI specification. However, a CopyObject to all other
object types should not perform an implicit conversion, as per
the ACPI specification.

http://www.acpica.org/bugzilla/show_bug.cgi?id=388Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fixed a problem where resource descriptor size optimization
could cause a problem when a _CRS resource template is passed
to a _SRS method. The _SRS resource template must use the same
descriptors (with the same size) as returned from _CRS. This
change affects the following resource descriptors: IRQ/IRQNoFlags
and StartDependendentFn/StartDependentFnNoPri.

http://bugzilla.kernel.org/show_bug.cgi?id=9487Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

New messages for the 2 AE_SUPPORT cases.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Added missing va_end statements that should correspond with each
va_start statement.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Implemented support for the use of DDBHandles as an Indexed
Reference, as per the ACPI spec.

http://www.acpica.org/bugzilla/show_bug.cgi?id=486.

Implemented support for UserTerm (Method invocation) for the Unload operator
as per the ACPI spec.

http://www.acpica.org/bugzilla/show_bug.cgi?id=580Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>