From Dave Johnson <djohnson+linuxmips@sw.starentnetworks.com>:
    
sb1250_gettimeoffset() simply reads the current cpu 0 timer remaining
value, however once this counter reaches 0 and the interrupt is raised,
it immediately resets and begins to count down again.
    
If sb1250_gettimeoffset() is called on cpu 1 via do_gettimeofday() after
the timer has reset but prior to cpu 0 processing the interrupt and
taking write_seqlock() in timer_interrupt() it will return a full value
(or close to it) causing time to jump backwards 1ms. Once cpu 0 handles
the interrupt and timer_interrupt() gets far enough along it will jump
forward 1ms.
    
Fix this problem by implementing mips_hpt_*() on sb1250 using a spare
timer unrelated to the existing periodic interrupt timers. It runs at
1Mhz with a full 23bit counter.  This eliminated the custom
do_gettimeoffset() for sb1250 and allowed use of the generic
fixed_rate_gettimeoffset() using mips_hpt_*() and timerhi/timerlo.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
From Dave Johnson <djohnson+linuxmips@sw.starentnetworks.com>:
    
Field width should be 23 bits not 20 bits.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
If a call to set_io_port_base() was being followed by usage of
mips_io_port_base in the same function gcc was possibly using the old
value due to some clever abuse of const.  Adding a barrier will keep
the optimization and result in correct code with latest gcc.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
If dcache_size != icache_size or dcache_size != scache_size, or
set-associative cache, icache/scache does not flushed properly.  Make
blast_?cache_page_indexed() masks its index value correctly.  Also,
use physical address for physically indexed pcache/scache.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
The SB1 core has a three cycle interrupt disable hazard but we were
wrongly treating it as fully interlocked.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
This is gluing the build of cirrusfb but really the mess that would need
cleaning and fixing is <video/vga.h> and <linux/vt_buffer.h> ...
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Reported and initial fix by Thomas Koeller <thomas.koeller@baslerweb.com>,
rewritten by me.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
A recent change requires cpu_possible_map to be initialized before
smp_sched_init() but most MIPS platforms were initializing their
processors in the prom_prepare_cpus callback of smp_prepare_cpus.  The
simple fix of calling prom_prepare_cpus from one of the earlier SMP
initialization hooks doesn't work well either since IPIs may require
init_IRQ() to have completed, so bit the bullet and split
prom_prepare_cpus into two initialization functions, plat_smp_setup
which is called early from setup_arch and plat_prepare_cpus called where
prom_prepare_cpus used to be called.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

(This really is only the half of the patch which was forgotten in
326a6257 ...)
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
It seems current get_user() incorrectly sign-extend an unsigned int
value on 64bit kernel.  I think this is because '(__typeof__(val))'
cast in final assignment.  I suppose the cast should be
'(__typeof__(*(addr))'.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Make new MADV_REMOVE, MADV_DONTFORK, MADV_DOFORK consistent across all
arches.  The idea is to make it possible to use them portably even before
distros include them in libc headers.

Move common flags to asm-generic/mman.h
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Currently, copy-on-write may change the physical address of a page even if the
user requested that the page is pinned in memory (either by mlock or by
get_user_pages).  This happens if the process forks meanwhile, and the parent
writes to that page.  As a result, the page is orphaned: in case of
get_user_pages, the application will never see any data hardware DMA's into
this page after the COW.  In case of mlock'd memory, the parent is not getting
the realtime/security benefits of mlock.

In particular, this affects the Infiniband modules which do DMA from and into
user pages all the time.

This patch adds madvise options to control whether memory range is inherited
across fork.  Useful e.g.  for when hardware is doing DMA from/into these
pages.  Could also be useful to an application wanting to speed up its forks
by cutting large areas out of consideration.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Acked-by: NHugh Dickins <hugh@veritas.com>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
From Richard Sandiford <richard@codesourcery.com>:
    
This patch caused a miscompilation of the restore_gp_regs() block
in restore_sigcontext().  This was in a 32-bit kernel compiled with
GCC CVS head.
    
restore_gp_regs() copies 64-bit user fields into 32-bit variables,
and in this combination, the new __get_user_asm_ll32() clobbers too
many registers.  It says:
    
/*
 * Get a long long 64 using 32 bit registers.
 */
{									\
	__asm__ __volatile__(						\
	"1:	lw	%1, (%3)				\n"	\
	"2:	lw	%D1, 4(%3)				\n"	\
	"	move	%0, $0					\n"	\
	"3:	.section	.fixup,\"ax\"			\n"	\
	"4:	li	%0, %4					\n"	\
	"	move	%1, $0					\n"	\
	"	move	%D1, $0					\n"	\
	"	j	3b					\n"	\
	"	.previous					\n"	\
	"	.section	__ex_table,\"a\"		\n"	\
	"	" __UA_ADDR "	1b, 4b				\n"	\
	"	" __UA_ADDR "	2b, 4b				\n"	\
	"	.previous					\n"	\
	: "=r" (__gu_err), "=&r" (val)					\
	: "0" (0), "r" (addr), "i" (-EFAULT));				\
}

and this requires val (%1) to be a 64-bit value.  In the case I saw,
gcc was using $3 for the 32-bit val, and wasn't expecting $4 to be
clobbered.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Add blast_xxx_range(), protected_blast_xxx_range() etc. for common
use.  They are built by __BUILD_BLAST_CACHE_RANGE().
Use protected_cache_op() macro for various protected_ routines.
Output code should be logically same.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
So we can get rid of config.h and the #ifdef crapola in the generic
timex.h.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

---

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

---

    
It's return value is ignored everywhere.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

---

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

---

A pile of internal functions use only inside mips io.h has names starting
with mem_... and clashing with names in drivers; renamed to __mem_....
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

A bunch of asm/bug.h includes are both not needed (since it will get
pulled anyway) and bogus (since they are done too early).  Removed.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

    
I've noticed that PCI clock was incorrectly reported as 66 MHz while being
mere 33 MHz on RBTX4937 board -- this was due to the different encoding of
the PCI divisor field in CCFG register between TX4927 and TX4937 chips...
    
Also, RBTX49x7 was printed out as a CPU name (e.g., "CPU is RBTX4937");
and some debug printk() were duplicating each other...
Signed-off-by: NKonstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
If mfc0 $12 follows store and the mfc0 is last instruction of a
page and fetching the next instruction causes TLB miss, the result
of the mfc0 might wrongly contain EXL bit.
    
ERT-TX49H2-027, ERT-TX49H3-012, ERT-TX49HL3-006, ERT-TX49H4-008
    
Workaround: mask EXL bit of the result or place a nop before mfc0.  It
doesn't harm to always clear those bits, so we change the code to do so.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

From Franck Bui-Huu <vagabon.xyz@gmail.com> with modifications by me.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
This fixes sparse warnings 'dereference of noderef expression'.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
fls was the only called of flz, so fold flz into fls, same for the
__ilog2 call.  Delete the now unused flz function.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
It always left the assembler in reorder mode possibly causing disaster.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Build blast_xxx, blast_xxx_page, blast_xxx_page_indexed from template.
Easier to maintaina and saves 300 lines.  Generated code should be
unchanged.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
AMD Au1200 SOC just doesn't have UART3, so KGDB won't even compile for it
as is, here's the fix to make KGDB use UART1.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Fix the #define's for TX4927/37 timer reg's to match the datasheets (those
Signed-off-by: NKonstantin Baydarov <kbaidarov@mvista.com>
Signed-off-by: NSergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>