No need to explicitly set the cell's platform_data/data_size.

Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use resource_size().
Signed-off-by: NChris Ball <cjb@laptop.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NChris Ball <cjb@laptop.org>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds support for power regulators.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Nkyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch is related to re-init processing on suspend/resume.

When card is resuming, some register is reset.  If card is removable,
maybe controller should be rescan for card.  But if assume card is
non-removable, need to restore the old value at registers.

We store the value of FIFOTH at probe time and then restore it in
dw_mci_resume().
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds quirks and capabilities to platdata.

Some cards don't use the CDn pin; in that case, we assume the card's
inserted. Some boards need other capabilities. So, we add capabilities
in the board's platdata.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Currently kunmap_atomic() doesn't take into account the offset, used
with kmap_atomic(). On platforms, where kunmap_atomic() is not a NOP,
this will lead to problems, when offset != 0.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

At power off, reset OCR mask to be the highest possible voltage
supported for the current mmc host.

This solves the re-initialization during the power up sequence.
The voltage may have been decreased due to the card accepts a lower
voltage than the voltage used during the initialization sequence.
We need to reset the voltage to by the host highest possible value
since according to specification the initialization must always be
done at high voltage.
Reviewed-by: NJonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

When using mmc_try_claim_host the corresponding release
function is mmc_do_release_host, which then also must
be exported.
Reviewed-by: NJonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: NSebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

During redetection of a SDIO card, a request for a new card RCA
was submitted to the card, but was then overwritten by the old RCA.
This caused the card to be deselected instead of selected when using
the incorrect RCA.  This bug's been present since the "oldcard"
handling was introduced in 2.6.32.
Signed-off-by: NStefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Reviewed-by: NUlf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: NPawel Wieczorkiewicz <pawel.wieczorkiewicz@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

count is only ever used by assigning to old_len if count == 0, and
then old_len isn't ever used at all.  So, both are redundant.  Fixes:

drivers/mmc/host/dw_mmc.c: In function ‘dw_mci_read_data_pio’:
drivers/mmc/host/dw_mmc.c:1034:32: warning: variable ‘old_len’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: NChris Ball <cjb@laptop.org>
Acked-by: NWill Newton <will.newton@imgtec.com>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Tested-by: NMarc Reilly <marc@cpdesign.com.au>
Tested-by: NEric Benard <eric@eukrea.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

It can be worked around using a GPIO which will be done for i.MX later.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Tested-by: NMarc Reilly <marc@cpdesign.com.au>
Tested-by: NEric Benard <eric@eukrea.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Tested-by: NMarc Reilly <marc@cpdesign.com.au>
Tested-by: NEric Benard <eric@eukrea.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

dma_unmap_sg() already flushes the cache, I don't get what this
code is doing here.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

To support MMC aggressive clock gating the driver has to stop the
interface clock when the .set_ios() method is called with .clock == 0.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some TOSHIBA MMC cards only support sector addressing even though the
size is < 2GB.  According to JEDEC Spec JESD84-A441-1 the ocr register
(bits 30, 29) determine byte/sector mode.  Use them.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

sdio_reset sends a CMD52 to reset the sdio card.  This is highly
recommended for sdio cards being reinitialized.  Since we do not
know if the card is being reinitialized we just send the command.
SD/eMMC cards are supposed to ignore the CMD before the CMD0.
Document why we are doing this.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds DDR mode support to dw_mmc.

If we set any bit in UHS_REG bit[16:31], the card of that slot is
supported for DDR mode.  For example, if UHS_REG[16] is set, card
number 0 is DDR mode.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

drivers/mmc/host/via-sdmmc.c: In function ‘via_reset_pcictrl’:
drivers/mmc/host/via-sdmmc.c:805:8: warning: variable ‘addrbase’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: NChris Ball <cjb@laptop.org>
Cc: Harald Welte <HaraldWelte@viatech.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

Fixes:

drivers/mmc/host/cb710-mmc.c: In function ‘cb710_wait_while_busy’:
drivers/mmc/host/cb710-mmc.c:182:6: warning: variable ‘err’ set but not
used [-Wunused-but-set-variable]
Signed-off-by: NChris Ball <cjb@laptop.org>
Acked-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

drivers/mmc/host/sdhci-pci.c: In function ‘sdhci_pci_probe_slot’:
drivers/mmc/host/sdhci-pci.c:913:18: warning: variable ‘addr’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: NChris Ball <cjb@laptop.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

This adds the mmc host driver for Freescale MXS-based SoC i.MX23/28.
The driver calls into mxs-dma via generic dmaengine api for both pio
and data transfer.

Thanks Chris Ball for the indentation patch.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NChris Ball <cjb@laptop.org>

This switches the mxcmmc driver to use the dmaengine API. Unlike
the old one this one is always present in the tree, even if no DMA
is implemented, hence we can remove all the #ifdefs in from the driver.
The driver automatically switches to PIO mode if no DMA support or no
suitable channel is available.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds support for 8-bit buswidth.
dw_mmc can use 8-bit buswidth and set to CTYPE_8BIT in card-type register.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use the new dmaengine helper functions, and drop the error check
on the returned cookier from the dmaengine - we recently
established that this is really not allowed to fail.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This variable doesn't seem to be used for anything after the
other patches so just drop it.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

According to the DMA-API you shall unmap the sglists with the same
sglist length as passed into the mapping function, not the
returned value from the mapping function.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use the new dmaengine helper functions, and drop the error check
on the returned cookier from the dmaengine - we recently
established that this is really not allowed to fail.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The host_sglen is now actually used to keep track of whether DMA
is active or not, so rename and retype it to bool.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

According to the DMA-API you shall unmap the sglists with the same
sglist length as passed into the mapping function, not the
returned value from the mapping function.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use the new dmaengine helpers to make the code more readable.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Fixes the following:
- It is perfectly legal for the dma_map_sg() to return fewer
  entries than were passed in.
- Supply the returned numer of (possibly coalesced) entries to
  the device_pre_slave_sg() function.
- Use the proper original sg_len when unmapping the sglist
  in the error path.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

So we know the implementation and prototypes agree with each other.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The test file is created under debugfs, not sysfs. Also remove
the unnecessary default n.
Signed-off-by: NWill Newton <will.newton@imgtec.com>
Reviewed-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NChris Ball <cjb@laptop.org>