Fixes (with v2.6.38-rc3/parisc/parisc-allmodconfig):
  src/drivers/i2c/busses/i2c-eg20t.c:720: error: implicit declaration of function 'kzalloc'
  src/drivers/i2c/busses/i2c-eg20t.c:790: error: implicit declaration of function 'kfree'
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

ocores_i2c_of_probe needs to use a const __be32 type for handing
device tree property values.  This patch fixed the following build
warning:

 CC      drivers/i2c/busses/i2c-ocores.o
  drivers/i2c/busses/i2c-ocores.c: In function 'ocores_i2c_of_probe':
  drivers/i2c/busses/i2c-ocores.c:254: warning: assignment discards qualifiers from pointer target type
  drivers/i2c/busses/i2c-ocores.c:261: warning: assignment discards qualifiers from pointer target type
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

For the I2C module to be wakeup capable, programming I2C_WE register (which
was skipped for OMAP4430) is needed even on OMAP4.

This fixes i2c controller timeouts which were seen recently with the static
dependency being cleared between MPU and L4PER clockdomains.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
[ben-linux@fluff.org: re-flowed description]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fixup the whitespace error noticed in cb527edeSigned-off-by: NBen Dooks <ben-linux@fluff.org>

This errata occurs when the ARDY interrupt generation is enabled.
At the begining of every new transaction the ARDY interrupt is cleared.

On continuous i2c transactions where after clearing the ARDY bit from
I2C_STAT register (clearing the interrupt), the IRQ line is reasserted and the
I2C_STAT[ARDY] bit set again on 1. In fact, the ARDY status bit is not cleared
at the write access to I2C_STAT[ARDY] and only the IRQ line is deasserted and
then reasserted. This is not captured in the usual errata documents.

The workaround is to have a double clear of ARDY status in irq handler.
Signed-off-by: NRichard woodruff <r-woodruff2@ti.com>
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

fix the build break when !CONFIG_SUSPEND

drivers/i2c/busses/i2c-omap.c:1173: error: lvalue required as unary '&' operand
make[3]: *** [drivers/i2c/busses/i2c-omap.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

When runtime PM is enabled, each OMAP i2c device is suspended after
each i2c xfer.  However, there are two cases when the static suspend
methods must be used to ensure the devices are suspended:

1) runtime PM is disabled, either at compile time or dynamically
    via /sys/devices/.../power/control.
2) an i2c client driver uses i2c during it's suspend callback, thus
   leaving the i2c driver active (NOTE: runtime suspend transitions are
   disabled during system suspend, so i2c activity during system
   suspend will runtime resume the device, but not runtime (re)suspend it.)

Since the actual work to suspend the device is handled by the
subsytem, call the bus methods to take care of it.

NOTE: This takes care of a known suspend problem on OMAP3 where the
TWL RTC driver does i2c xfers during its suspend path leaving the i2c
driver in an active state (since runtime suspend transistions are
disabled.)
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Use strlcpy instead of strncpy.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Having conditional around the of_match_table and the of_node pointers
turns out to make driver code use ugly #ifdef blocks.  Drop the
conditionals and remove the #ifdef blocks from the affected drivers.

Also tidy up minor whitespace issues within the same hunks.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since the PM core wishes to transition away from the legacy suspend
and resume methods and since removing them makes using PM core features
like runtime PM much easier start warning when a driver is registered
using the legacy methods.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

When devices use dev_pm_ops the I2C API is implementing standard functionality
for integration with runtime PM and for checking for the presence of a per
device op. The PM core provides pm_generic_ functions implementing this
behaviour - use them to reduce coupling with future PM updates.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Remove real devices first and dummy devices last. This gives device
driver which instantiated dummy devices themselves a chance to clean
them up before we do.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NHans Verkuil <hverkuil@xs4all.nl>
Cc: stable@kernel.org

The SCx200 ACB driver supports ISA hardware as well as PCI.  The PCI
hardware is CS5535/CS5536 based, and the device that it grabs is handled by
the cs5535-mfd driver. This converts the SCx200 driver to use a
platform_driver rather than the previous PCI hackery.

The driver used to manually track the iface list (via linked list); now it
only does this for ISA devices.  PCI ifaces are handled through standard
driver model lists.

It's unclear what happens in case of errors in the old ISA code; rather than
pretending the code actually cares, I've dropped the (implicit) ignorance
of return values and marked it with a comment.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some systems using this bus sometimes have very basic devices such as
regulators on the bus, so the I2C bus master needs to be loaded early.
This also matches the behavior of many other I2C bus master drivers.
Therefore initialize via subsys_initcall().
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Faulty slave devices might drive SDA low after a transfer finishes.  So,
when this scenario is detected, have the master generate up to 9 extra
clocks until the SDA is properly released.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Helper functions for I2C and SMBus transactions don't modify the
i2c_client that is passed to them, so it can be marked const.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The I2C specification explicitly describes both SDA and SCL as
bidirectional lines. An I2C master with a read-only SCL is thus not
compliant. If a slow slave stretches the clock, errors will happen,
so the bus can't be considered as reliable.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Use a function pointer to decide whether to call i2c_add_adapter or
i2c_add_numbered_adapter. This makes the code more compact than the
current strategy of having the common code in a separate function.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add an i2c mux driver providing access to i2c bus segments using a
hardware MUX sitting on a master bus and controlled through gpio pins.

E.G. something like:

  ----------              ----------  Bus segment 1   - - - - -
 |          | SCL/SDA    |          |-------------- |           |
 |          |------------|          |
 |          |            |          | Bus segment 2 |           |
 |  Linux   | GPIO 1..N  |   MUX    |---------------   Devices
 |          |------------|          |               |           |
 |          |            |          | Bus segment M
 |          |            |          |---------------|           |
  ----------              ----------                  - - - - -

SCL/SDA of the master I2C bus is multiplexed to bus segment 1..M
according to the settings of the GPIO pins 1..N.
Signed-off-by: NPeter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Commit 5a0e3ad6 added direct inclusion
of <linux/slab.h> to those source files that appeared to need it, but
somehow missed this.  On most architectures <linux/slab.h> is still
indirectly included, but there are exceptions such as alpha.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

As stated into file include/linux/i2c.h we must send a repeated START
between messages in the same xfer groupset:

 * Except when I2C "protocol mangling" is used, all I2C adapters implement
 * the standard rules for I2C transactions.  Each transaction begins with a
 * START.  That is followed by the slave address, and a bit encoding read
 * versus write.  Then follow all the data bytes, possibly including a byte
 * with SMBus PEC.  The transfer terminates with a NAK, or when all those
 * bytes have been transferred and ACKed.  If this is the last message in a
 * group, it is followed by a STOP.  Otherwise it is followed by the next
 * @i2c_msg transaction segment, beginning with a (repeated) START.
Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Signed-off-by: NMauro Barella <mbarella@vds-it.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The Nomadik I2C adapter does not provide a name for the struct
passed into i2c_add_numbered_adapter() causing a regression on
2.6.37-rc3 due to commit 2236baa7
adding sanity checks for adapters. Fix this by providing a name
proper.

Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Ordinary I2C read consist of two messages. First a write operation
to tell register address and then read operation to get data.
CPU wake up latency is set and removed twice in read case.
Set latency requirement before the message processing loop
and remove the requirement after the loop to remove latency
adjustment operations between the messages.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

I2C driver for Intel EG20T PCH
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Reviewed-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NQi Wang <qi.wang@intel.com>
[ben-linux@fluff.org: reworded commit message]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This puts some documentation for the device tree configuration at the head
of the driver file.  Hopefully this can get moved to a common area for this
type of documentation at a later date; unfortunately, there isn't really
such a place in the kernel tree at this time.

Furthermore, the regstep and clock-frequency parameters are really bus
parameters and should probably be passed to the driver in a better way.
Consider that a TODO.
Signed-off-by: NJonas Bonn <jonas@southpole.se>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch converts the i2c-cores driver to use devres routines for
resource allocation.
Signed-off-by: NJonas Bonn <jonas@southpole.se>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch adapts the i2c-ocores driver for being defined and configured via
a device tree description.

The device tree bits need to be protected by CONFIG_OF guards as this is
still an optional feature.
Signed-off-by: NJonas Bonn <jonas@southpole.se>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Eliminate unnecessary casts and the following sparse warnings:

	drivers/i2c/busses/i2c-iop3xx.c:65:9: warning: incorrect type in argument 1 (different base types)
	drivers/i2c/busses/i2c-iop3xx.c:65:9:    expected void const volatile [noderef] <asn:2>*<noident>
	drivers/i2c/busses/i2c-iop3xx.c:65:9:    got unsigned int

	[ the previous warning is repeated 18 times ]

	drivers/i2c/busses/i2c-iop3xx.c:456:33: warning: cast removes address space of expression
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The convention for omap device naming is omap_XXX.

Rename the device and driver name in order to stick
to this naming convention.

Change device name in clock nodes as well.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This gets caught by the new sanity check code. Instead of the slash use a
different symbol. This was originally found by Major Lee who proposed a
rather more complex patch which changed the name according to the chip
type.

On the basis that we are in a late -rc and making Linus grumpy isn't always
a good idea (however fun) this is a simple alternative.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NArnaud Lacombe <lacombar@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This reverts commit 0a57274e.
Signed-off-by: NArnaud Lacombe <lacombar@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make sure I2C adapters being registered have the required struct
fields set. If they don't, problems will happen later.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

It's about time to make it clear that i2c_adapter.id is deprecated.
Hopefully this will remind the last user to move over to a different
strategy.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NJarod Wilson <jarod@redhat.com>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>

This patch converts the i2c driver to use PM runtime apis
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

These are the extra 'Integrated Device Function' SMBus controllers found
on the Patsburg chipset. Mention the absence of slave mode support.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

It's poor form to keep driver state in global variables rather than
per-instance. It never really mattered in practice when there was only
one controller on the chipset, but the latest chipsets do have more
than one controller, so now we care.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add support for the Intel Patsburg PCH SMBus Controller.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>