It appears that the error paths were overlooked when the
omap3_pm_init() routine had the prcm chain handler code
added.  Fix this by adding a goto target and reordering
the error handling code.  Also fix how the irq argument
for free_irq() is determined.
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

On OMAP4, recently a synchronisation bug is discovered by hardware
team, which leads to incorrect timer value read from 32K sync timer
IP when the IP is comming out of idle.

The issue is due to the synchronization methodology used in the SYNCTIMER IP.
The value of the counter register in 32kHz domain is synchronized to the OCP
domain register only at count up event, and if the OCP clock is switched off,
the OCP register gets out of synch until the first count up event after the
clock is switched back -at the next falling edge of the 32kHz clock.

Further investigation revealed that it applies to gptimer1 and watchdog timer2
as well which may run on 32KHz. This patch fixes the issue for all the
applicable modules.

The BUG has not made it yet to the OMAP errata list and it is applicable to
OMAP1/2/3/4/5. OMAP1/2/3 it is taken care indirectly by autodeps.

By enabling static depedency of wakeup clockdomain with MPU, as soon as MPU
is woken up from lowpower state(idle) or whenever MPU is active, PRCM forces
the OCP clock to be running and allow the counter value to be updated properly
in the OCP clock domain.

The bug is going to fixed in future OMAP versions.

Reported-Tested-by: dave.long@linaro.org
[dave.long@linaro.org: Reported the oprofile time stamp issue with synctimer
and helped to test this patch]
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Commit 28d82dc1 ("epoll: limit paths") that I did to limit the
number of possible wakeup paths in epoll is causing a few applications
to longer work (dovecot for one).

The original patch is really about limiting the amount of epoll nesting
(since epoll fds can be attached to other fds). Thus, we probably can
allow an unlimited number of paths of depth 1. My current patch limits
it at 1000. And enforce the limits on paths that have a greater depth.

This is captured in: https://bugzilla.redhat.com/show_bug.cgi?id=681578Signed-off-by: NJason Baron <jbaron@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull networking changes from David Miller:
 "1) icmp6_dst_alloc() returns NULL instead of ERR_PTR() leading to
     crashes, particularly during shutdown.  Reported by Dave Jones and
     fixed by Eric Dumazet.

  2) hyperv and wimax/i2400m return NETDEV_TX_BUSY when they have
     already freed the SKB, which causes crashes as to the caller this
     means requeue the packet.  Fixes from Eric Dumazet.

  3) usbnet driver doesn't allocate the right amount of headroom on
     fresh RX SKBs, fix from Eric Dumazet.

  4) Fix regression in ip6_mc_find_dev_rcu(), as an RCU lookup it
     abolutely should not take a reference to 'dev', this leads to
     leaks.  Fix from RonQing Li.

  5) Fix netfilter ctnetlink race between delete and timeout expiration.
     From Pablo Neira Ayuso.

  6) Revert SFQ change which causes regressions, specifically queueing
     to tail can lead to unavoidable flow starvation.  From Eric
     Dumazet.

  7) Fix a memory leak and a crash on corrupt firmware files in bnx2x,
     from Michal Schmidt."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  netfilter: ctnetlink: fix race between delete and timeout expiration
  ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
  wimax/i2400m: fix erroneous NETDEV_TX_BUSY use
  net/hyperv: fix erroneous NETDEV_TX_BUSY use
  net/usbnet: reserve headroom on rx skbs
  bnx2x: fix memory leak in bnx2x_init_firmware()
  bnx2x: fix a crash on corrupt firmware file
  sch_sfq: revert dont put new flow at the end of flows
  ipv6: fix icmp6_dst_alloc()

Pull perf fixes from Ingo Molnar.

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools, x86: Build perf on older user-space as well
  perf tools: Use scnprintf where applicable
  perf tools: Incorrect use of snprintf results in SEGV

Kerin Millar reported hardlockups while running `conntrackd -c'
in a busy firewall. That system (with several processors) was
acting as backup in a primary-backup setup.

After several tries, I found a race condition between the deletion
operation of ctnetlink and timeout expiration. This patch fixes
this problem.
Tested-by: NKerin Millar <kerframil@gmail.com>
Reported-by: NKerin Millar <kerframil@gmail.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip6_mc_find_dev_rcu() is called with rcu_read_lock(), so don't
need to dev_hold().
With dev_hold(), not corresponding dev_put(), will lead to leak.

[ bug introduced in 96b52e61 (ipv6: mcast: RCU conversions) ]
Signed-off-by: NRongQing.Li <roy.qing.li@gmail.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge some more email patches from Andrew Morton:
 "A couple of nilfs fixes"

* emailed from Andrew Morton <akpm@linux-foundation.org>:
  nilfs2: fix NULL pointer dereference in nilfs_load_super_block()
  nilfs2: clamp ns_r_segments_percentage to [1, 99]

According to the report from Slicky Devil, nilfs caused kernel oops at
nilfs_load_super_block function during mount after he shrank the
partition without resizing the filesystem:

 BUG: unable to handle kernel NULL pointer dereference at 00000048
 IP: [<d0d7a08e>] nilfs_load_super_block+0x17e/0x280 [nilfs2]
 *pde = 00000000
 Oops: 0000 [#1] PREEMPT SMP
 ...
 Call Trace:
  [<d0d7a87b>] init_nilfs+0x4b/0x2e0 [nilfs2]
  [<d0d6f707>] nilfs_mount+0x447/0x5b0 [nilfs2]
  [<c0226636>] mount_fs+0x36/0x180
  [<c023d961>] vfs_kern_mount+0x51/0xa0
  [<c023ddae>] do_kern_mount+0x3e/0xe0
  [<c023f189>] do_mount+0x169/0x700
  [<c023fa9b>] sys_mount+0x6b/0xa0
  [<c04abd1f>] sysenter_do_call+0x12/0x28
 Code: 53 18 8b 43 20 89 4b 18 8b 4b 24 89 53 1c 89 43 24 89 4b 20 8b 43
 20 c7 43 2c 00 00 00 00 23 75 e8 8b 50 68 89 53 28 8b 54 b3 20 <8b> 72
 48 8b 7a 4c 8b 55 08 89 b3 84 00 00 00 89 bb 88 00 00 00
 EIP: [<d0d7a08e>] nilfs_load_super_block+0x17e/0x280 [nilfs2] SS:ESP 0068:ca9bbdcc
 CR2: 0000000000000048

This turned out due to a defect in an error path which runs if the
calculated location of the secondary super block was invalid.

This patch fixes it and eliminates the reported oops.
Reported-by: NSlicky Devil <slicky.dvl@gmail.com>
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: NSlicky Devil <slicky.dvl@gmail.com>
Cc: <stable@vger.kernel.org>	[2.6.30+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ns_r_segments_percentage is read from the disk.  Bogus or malicious
value could cause integer overflow and malfunction due to meaningless
disk usage calculation.  This patch reports error when mounting such
bogus volumes.
Signed-off-by: NHaogang Chen <haogangchen@gmail.com>
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull maintainer update from James Morris:
 "Please pull this patch which adds Serge as maintainer of the
  capabilities code, as discussed on lwn and the lsm list.

  New capabilities must be signed off by the maintainer, and new uses of
  any capabilities should at be cc'd to the maintainer."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  MAINTAINERS: Add Serge as maintainer of capabilities

Pull c6x bugfix from Mark Salter:
 "Remove dead code from entry.S which causes a build failure when using
  a newer assembler (v2.22 complains about it, v2.20 ignores it)."

* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
  C6X: remove dead code from entry.S

When writing files to afs I sometimes hit a BUG:

kernel BUG at fs/afs/rxrpc.c:179!

With a backtrace of:

	afs_free_call
	afs_make_call
	afs_fs_store_data
	afs_vnode_store_data
	afs_write_back_from_locked_page
	afs_writepages_region
	afs_writepages

The cause is:

	ASSERT(skb_queue_empty(&call->rx_queue));

Looking at a tcpdump of the session the abort happens because we
are exceeding our disk quota:

	rx abort fs reply store-data error diskquota exceeded (32)

So the abort error is valid. We hit the BUG because we haven't
freed all the resources for the call.

By freeing any skbs in call->rx_queue before calling afs_free_call
we avoid hitting leaking memory and avoid hitting the BUG.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A read of a large file on an afs mount failed:

# cat junk.file > /dev/null
cat: junk.file: Bad message

Looking at the trace, call->offset wrapped since it is only an
unsigned short. In afs_extract_data:

        _enter("{%u},{%zu},%d,,%zu", call->offset, len, last, count);
...

        if (call->offset < count) {
                if (last) {
                        _leave(" = -EBADMSG [%d < %zu]", call->offset, count);
                        return -EBADMSG;
                }

Which matches the trace:

[cat   ] ==> afs_extract_data({65132},{524},1,,65536)
[cat   ] <== afs_extract_data() = -EBADMSG [0 < 65536]

call->offset went from 65132 to 0. Fix this by making call->offset an
unsigned int.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ENDPROC() on sys_fadvise64_c6x() in arch/c6x/kernel/entry.S is
outside of the conditional block with the matching ENTRY() macro. This
leads a newer (v2.22 vs. v2.20) assembler to complain:

  /tmp/ccGZBaPT.s: Assembler messages:
  /tmp/ccGZBaPT.s: Error: .size expression for sys_fadvise64_c6x does not evaluate to a constant

The conditional block became dead code when c6x switched to generic
unistd.h and should be removed along with the offending ENDPROC().
Signed-off-by: NMark Salter <msalter@redhat.com>
Acked-by: NDavid Howells <dhowells@redhat.com>

A driver start_xmit() method cannot free skb and return NETDEV_TX_BUSY,
since caller is going to reuse freed skb.

In fact netif_tx_stop_queue() / netif_stop_queue() is needed before
returning NETDEV_TX_BUSY or you can trigger a ksoftirqd fatal loop.

In case of memory allocation error, only safe way is to drop the packet
and return NETDEV_TX_OK

Also increments tx_dropped counter
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A driver start_xmit() method cannot free skb and return NETDEV_TX_BUSY,
since caller is going to reuse freed skb.

This is mostly a revert of commit bf769375 (staging: hv: fix the return
status of netvsc_start_xmit())

In fact netif_tx_stop_queue() / netif_stop_queue() is needed before
returning NETDEV_TX_BUSY or you can trigger a ksoftirqd fatal loop.

In case of memory allocation error, only safe way is to drop the packet
and return NETDEV_TX_OK
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

network drivers should reserve some headroom on incoming skbs so that we
dont need expensive reallocations, eg forwarding packets in tunnels.

This NET_SKB_PAD padding is done in various helpers, like
__netdev_alloc_skb_ip_align() in this patch, combining NET_SKB_PAD and
NET_IP_ALIGN magic.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When cycling the interface down and up, bnx2x_init_firmware() knows that
the firmware is already loaded, but nevertheless it allocates certain
arrays anew (init_data, init_ops, init_ops_offsets, iro_arr). The old
arrays are leaked.

Fix the leaks by returning early if the firmware was already loaded.
Because if the firmware is loaded, so are the arrays.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the requested firmware is deemed corrupt and then released, reset the
pointer to NULL in order to avoid double-freeing it in
bnx2x_release_firmware() or dereferencing it in bnx2x_init_firmware().
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit d47a0ac7 (sch_sfq: dont put new flow at the end of
flows)

As Jesper found out, patch sounded great but has bad side effects.

In stress situation, pushing new flows in front of the queue can prevent
old flows doing any progress. Packets can stay in SFQ queue for
unlimited amount of time.

It's possible to add heuristics to limit this problem, but this would
add complexity outside of SFQ scope.

A more sensible answer to Dave Taht concerns (who reported the issued I
tried to solve in original commit) is probably to use a qdisc hierarchy
so that high prio packets dont enter a potentially crowded SFQ qdisc.
Reported-by: NJesper Dangaard Brouer <jdb@comx.dk>
Cc: Dave Taht <dave.taht@gmail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 87a11578 ( ipv6: Move xfrm_lookup() call down into
icmp6_dst_alloc().) forgot to convert one error path, leading
to crashes in mld_sendpack()

Many thanks to Dave Jones for providing a very complete bug report.
Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Serge as maintainer of capabilities, per suggestion on LWN:
http://lwn.net/Articles/486306/Signed-off-by: NJames Morris <james.l.morris@oracle.com>

Merge patches from Andrew Morton:
 "Nine patches - some bug fixes and some MAINTAINERS fiddling."

* emailed from Andrew Morton <akpm@linux-foundation.org>:
  drivers/video/backlight/s6e63m0.c: fix corruption storing gamma mode
  MAINTAINERS: add entry for exynos mipi display drivers
  MAINTAINERS: fix link to Gustavo Padovans tree
  MAINTAINERS: add Johan to Bluetooth maintainers
  MAINTAINERS: Gustavo has moved
  prctl: use CAP_SYS_RESOURCE for PR_SET_MM option
  rapidio/tsi721: fix bug in register offset definitions
  MAINTAINERS: update ST's Mailing list for SPEAr
  memcg: free mem_cgroup by RCU to fix oops

Pull i2c subsystem fixes from Jean Delvare.

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c-algo-bit: Fix spurious SCL timeouts under heavy load
  i2c-core: Comment says "transmitted" but means "received"

Pull hwmon fixes from Guenter Roeck.

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (zl6100) Enable interval between chip accesses for all chips
  hwmon: (w83627ehf) Describe undocumented pwm attributes
  hwmon: (w83627ehf) Fix temp2 source for W83627UHG
  hwmon: (w83627ehf) Fix memory leak in probe function
  hwmon: (w83627ehf) Fix writing into fan_stop_time for NCT6775F/NCT6776F

Pull drm exynos/intel updates from Dave Airlie:
 "Two minor updates from Jesse for Intel SNB fixes, and a few fixes from
  Samsung for exynos.  The pull req has Alan's commit in it since Intel
  based their tree on my tree at that time, but it all seems fine wrt
  merging."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm exynos: use drm_fb_helper_set_par directly
  drm/exynos: Fix fb_videomode <-> drm_mode_modeinfo conversion
  drm/exynos: fix runtime_pm fimd device state on probe
  drm/exynos: use correct 'exynos-drm' name for platform device
  drm/i915: support 32 bit BGR formats in sprite planes
  drm/i915: fix color order for BGR formats on SNB
  drm/gma500: Fix Cedarview boot failures in 3.3-rc

Pull media fixes from Mauro Carvalho Chehab:
 "For 4 fixes for 3.3 (all trivial):
       - uvc video driver: fixes a division by zero;
       - davinci: add module.h to fix compilation;
       - smsusb: fix the delivery system setting;
       - smsdvb: the get_frontend implementation there is broken.

  The smsdvb patch has 127 lines, but it is trivial: instead of
  returning a cache of the set_frontend (with is wrong, as it doesn't
  have the updated values for the data, and the implementation there is
  buggy), it copies the information of the detected DVB parameters from
  the smsdvb private structures into the corresponding DVBv5 struct
  fields."

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] smsdvb: fix get_frontend
  [media] smsusb: fix the default delivery system setting
  [media] media: davinci: added module.h to resolve unresolved macros
  [media] [FOR,v3.3] uvcvideo: Avoid division by 0 in timestamp calculation

Pull target fixes from Nicholas Bellinger:
 "This series addresses two recently reported regression bugs related to
  legacy SCSI reservation usage in target core, and iscsi-target
  reservation conflict handling.

  The second patch in particular addresses possible data-corruption with
  SCSI reservations that is specific to iscsi-target fabric LUNs with
  multiple client writers.  Both patches need to go into v3.2 stable
  ASAP, and the branch based on the last target-pending/3.3-rc-fixes
  HEAD.

  Again, thanks to Martin Svec for his help to identify and address this
  regression bug with iscsi-target."

* '3.3-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target: Fix reservation conflict -EBUSY response handling bug
  target: Fix compatible reservation handling (CRH=1) with legacy RESERVE/RELEASE

strict_strtoul() writes a long but ->gamma_mode only has space to store an
int, so on 64 bit systems we end up scribbling over ->gamma_table_count as
well.  I've changed it to use kstrtouint() instead.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I'd like to add Inki Dae, Donghwa Lee and Kyungmin Park as maintainers
who developers for exynos mipi display drivers for
video/driver/exynos/exynos_mipi* and include/video/exynos_mipi*.
Signed-off-by: NDonghwa Lee <dh09.lee@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Gustavo's tree is called just bluetooth.git and not bluetooth-2.6.git
anymore.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I've been coordinating Bluetooth patches in my tree for some time and
it's possible I'll do it in the future too, so add myself to the
Bluetooth sections as well as mention my tree there.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is going to be the primary e-mail for kernel development.
Signed-off-by: NGustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

CAP_SYS_ADMIN is already overloaded left and right, so to have more
fine-grained access control use CAP_SYS_RESOURCE here.

The CAP_SYS_RESOUCE is chosen because this prctl option allows a current
process to adjust some fields of memory map descriptor which rather
represents what the process owns: pointers to code, data, stack
segments, command line, auxiliary vector data and etc.
Suggested-by: NMichael Kerrisk <mtk.manpages@gmail.com>
Acked-by: NKees Cook <keescook@chromium.org>
Acked-by: NMichael Kerrisk <mtk.manpages@gmail.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix indexed register offset definitions that use decimal (wrong) instead
of hexadecimal (correct) notation for indexing multipliers.

Incorrect definitions do not affect Tsi721 driver in its current default
configuration because it uses only IDB queue 0.  Loss of inbound
doorbell functionality should be observed if queue other than 0 is used.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Chul Kim <chul.kim@idt.com>
Cc: <stable@vger.kernel.org>		[3.2+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We have created a ST's Mailing list for SPEAr.  This can be accessed
from non-st email ids.  I want people to cc this list, when they have
changes specific to SPEAr.  So, its better to get this updated in
MAINTAINERS file.

linux-arm-kernel@lists.infradead.org is also added for SPEAr.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After fixing the GPF in mem_cgroup_lru_del_list(), three times one
machine running a similar load (moving and removing memcgs while
swapping) has oopsed in mem_cgroup_zone_nr_lru_pages(), when retrieving
memcg zone numbers for get_scan_count() for shrink_mem_cgroup_zone():
this is where a struct mem_cgroup is first accessed after being chosen
by mem_cgroup_iter().

Just what protects a struct mem_cgroup from being freed, in between
mem_cgroup_iter()'s css_get_next() and its css_tryget()? css_tryget()
fails once css->refcnt is zero with CSS_REMOVED set in flags, yes: but
what if that memory is freed and reused for something else, which sets
"refcnt" non-zero? Hmm, and scope for an indefinite freeze if refcnt is
left at zero but flags are cleared.

It's tempting to move the css_tryget() into css_get_next(), to make it
really "get" the css, but I don't think that actually solves anything:
the same difficulty in moving from css_id found to stable css remains.

But we already have rcu_read_lock() around the two, so it's easily fixed
if __mem_cgroup_free() just uses kfree_rcu() to free mem_cgroup.

However, a big struct mem_cgroup is allocated with vzalloc() instead of
kzalloc(), and we're not allowed to vfree() at interrupt time: there
doesn't appear to be a general vfree_rcu() to help with this, so roll
our own using schedule_work().  The compiler decently removes
vfree_work() and vfree_rcu() when the config doesn't need them.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ying Han <yinghan@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When the system is under heavy load, there can be a significant delay
between the getscl() and time_after() calls inside sclhi(). That delay
may cause the time_after() check to trigger after SCL has gone high,
causing sclhi() to return -ETIMEDOUT.

To fix the problem, double check that SCL is still low after the
timeout has been reached, before deciding to return -ETIMEDOUT.
Signed-off-by: NVille Syrjala <syrjala@sci.fi>
Cc: stable@vger.kernel.org
Signed-off-by: NJean Delvare <khali@linux-fr.org>