If a PHB has no I/O space, there's no need to make it look like
something bad happened, a pr_debug() is plenty enough since this
is the case of all our modern POWER chips.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

On the PCI plugging event, PCI slot's subordinate devices are
scanned and their (IO and MMIO) resources are assigned. Platform
dependent resources (PE#, IO/MMIO/DMA windows) are allocated or
created on updating windows of the slot's upstream bridge.

This updates the windows of the hot plugged slot's upstream bridge
in pcibios_finish_adding_to_bus() so that the platform resources
(PE#, IO/MMIO/DMA segments) are allocated or created accordingly.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This overrides pcibios_setup_bridge() that is called to update PCI
bridge windows when PCI resource assignment is completed, to assign
PE and setup various (resource) mapping for the PE in subsequent
patches.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Export pcibios_free_controller(), so it can be used by the cxl module to
free virtual PHBs.
Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Revert dff22d20 ("PCI: Call pci_read_bridge_bases() from core instead
of arch code").

Reading PCI bridge windows is not arch-specific in itself, but there is PCI
core code that doesn't work correctly if we read them too early.  For
example, Hannes found this case on an ARM Freescale i.mx6 board:

  pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
  pci 0000:00:00.0: PCI bridge to [bus 01-ff]
  pci 0000:00:00.0: BAR 8: no space for [mem size 0x01000000] (mem window)
  pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00200000]
  pci 0000:01:00.0: BAR 1: failed to assign [mem size 0x00004000]
  pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00000100]

The 00:00.0 mem window needs to be at least 3MB: the 01:00.0 device needs
0x204100 of space, and mem windows are megabyte-aligned.

Bus sizing can increase a bridge window size, but never *decrease* it (see
d65245c3 ("PCI: don't shrink bridge resources")).  Prior to
dff22d20, ARM didn't read bridge windows at all, so the "original size"
was zero, and we assigned a 3MB window.

After dff22d20, we read the bridge windows before sizing the bus.  The
firmware programmed a 16MB window (size 0x01000000) in 00:00.0, and since
we never decrease the size, we kept 16MB even though we only needed 3MB.
But 16MB doesn't fit in the host bridge aperture, so we failed to assign
space for the window and the downstream devices.

I think this is a defect in the PCI core: we shouldn't rely on the firmware
to assign sensible windows.

Ray reported a similar problem, also on ARM, with Broadcom iProc.

Issues like this are too hard to fix right now, so revert dff22d20.
Reported-by: NHannes <oe5hpm@gmail.com>
Reported-by: NRay Jui <rjui@broadcom.com>
Link: http://lkml.kernel.org/r/CAAa04yFQEUJm7Jj1qMT57-LG7ZGtnhNDBe=PpSRa70Mj+XhW-A@mail.gmail.com
Link: http://lkml.kernel.org/r/55F75BB8.4070405@broadcom.comSigned-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Use %pR to simplify the debug code. This also make the debug info more
readable.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
[mpe: Unsplit multi-line printk strings]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy.  Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.

Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.

For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.

[bhelgaas: changelog]
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>

This adds a hook into the powerpc pci code for pci_disable_device() calls.  The
generic code already provides a weak pcibios_disable_device() symbol, so we
just need to provide our own in powerpc and it'll get picked up.

This is passed directly to the phb controller ops, provided one exists.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Export pcibios_claim_one_bus, pcibios_scan_phb and pcibios_alloc_controller.

These will be used by the CXL driver.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Remove shims, patch callsites to use pci_controller_ops
versions instead.

Also move back the probe mode defines, as explained in the patch
for pci_probe_mode.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.reset_secondary_bus,
shadowing ppc_md.pcibios_reset_secondary_bus.
Add a shim, and changes the callsites to use the shim.

Use pcibios_reset_secondary_bus_shim, as both
pcibios_reset_secondary_bus and pci_reset_secondary_bus
are already taken.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.window_alignment,
shadowing ppc_md.pcibios_window_alignment.
Add a shim, and changes the callsites to use the shim.

Here, we use pci_window_alignment, as pcibios_window_alignment is
already taken.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.enable_device_hook,
shadowing ppc_md.pcibios_enable_device_hook.
Add a shim, and changes the callsites to use the shim.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.probe_mode, shadowing ppc_md.pci_probe_mode.
Add a shim, and changes the callsites to use the shim.

We also need to move the probe mode defines to pci-bridge.h from pci.h.
They are required by the shim in order to return a sensible default.
Previously, the were defined in pci.h, but pci.h includes pci-bridge.h
before the relevant #defines. This means the definitions are absent
if pci.h is included before pci-bridge.h. This occurs in some drivers.
So, move the definitons now, and move them back when we remove the shim.

Anything that wants the defines would have had to include pci.h, and
since pci.h includes pci-bridge.h, nothing will lose access to the
defines.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.dma_bus_setup, shadowing ppc_md.pci_dma_bus_setup.
Add a shim, and changes the callsites to use the shim.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Introduces the pci_controller_ops structure.
Add pci_controller_ops.dma_dev_setup, shadowing ppc_md.pci_dma_dev_setup.
Add a shim, and change the callsites to use the shim.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

pcibios_enable_device_hook returned an int. Every implementation
returned either -EINVAL or 0. The return value wasn't propagated by
the caller: any non-zero return value caused pcibios_enable_device
to return -EINVAL itself. Therefore, make the hook return a bool.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We have a powerpc specific global called mem_init_done which is "set on
boot once kmalloc can be called".

But that's not *quite* true. We set it at the bottom of mem_init(), and
rely on the fact that mm_init() calls kmem_cache_init() immediately
after that, and nothing is running in parallel.

So replace it with the generic and 100% correct slab_is_available().
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Implement pcibios_iov_resource_alignment() on powernv platform.

On PowerNV platform, there are 3 cases for the IOV BAR:
1. initial state, the IOV BAR size is multiple times of VF BAR size
2. after expanded, the IOV BAR size is expanded to meet the M64 segment size
3. sizing stage, the IOV BAR is truncated to 0

pnv_pci_iov_resource_alignment() handle these three cases respectively.

[bhelgaas: adjust to drop "align" parameter, return pci_iov_resource_size()
if no ppc_md machdep_call version]
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On PHB3, PF IOV BAR will be covered by M64 BAR to have better PE isolation.
M64 BAR is a type of hardware resource in PHB3, which could map a range of
MMIO to PE numbers on powernv platform. And this range is divided equally
by the number of total_pe with each divided range mapping to a PE number.
Also, the M64 BAR must map a MMIO range with power-of-two size.

The total_pe number is usually different from total_VFs, which can lead to
a conflict between MMIO space and the PE number.

For example, if total_VFs is 128 and total_pe is 256, the second half of
M64 BAR will be part of other PCI device, which may already belong to other
PEs.

This patch prevents the conflict by reserving additional space for the PF
IOV BAR, which is total_pe number of VF's BAR size.

[bhelgaas: make dev_printk() output more consistent, index resource[]
conventionally]
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Flag PCI_REASSIGN_ALL_RSRC is used to ignore resources information setup by
firmware, so that kernel would re-assign all resources of pci devices.

On powerpc arch, this happens in a header fixup function
pcibios_fixup_resources(), which will clean up the resources if this flag
is set. This works fine for PFs, since after clean up, kernel will
re-assign the resources in pcibios_resource_survey().

Below is a simple call flow on how it works:

    pcibios_init
      pcibios_scan_phb
        pci_scan_child_bus
          ...
            pci_device_add
              pci_fixup_device(pci_fixup_header)
                pcibios_fixup_resources                     # header fixup
                  for (i = 0; i < DEVICE_COUNT_RESOURCE; i++)
                    dev->resource[i].start = 0
      pcibios_resource_survey                               # re-assign
        pcibios_allocate_resources

However, the VF resources won't be re-assigned, since the VF resources are
completely determined by the PF resources, and the PF resources have
already been reassigned. This means we need to leave VF's resources
un-cleared in pcibios_fixup_resources().

In this patch, we skip the resource unset process in
pcibios_fixup_resources(), if the pci_dev is a VF.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge.  If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.

[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491Reported-by: NMarek Kordik <kordikmarek@gmail.com>
Fixes: 5b285415 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Gavin Shan <gwshan@linux.vnet.ibm.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: Wei Yang <weiyang@linux.vnet.ibm.com>
CC: Andrew Murray <amurray@embedded-bits.co.uk>
CC: linuxppc-dev@lists.ozlabs.org

Although we are now selecting NO_BOOTMEM, we still have some traces of
bootmem lying around. That is because even with NO_BOOTMEM there is
still a shim that converts bootmem calls into memblock calls, but
ultimately we want to remove all traces of bootmem.

Most of the patch is conversions from alloc_bootmem() to
memblock_virt_alloc(). In general a call such as:

  p = (struct foo *)alloc_bootmem(x);

Becomes:

  p = memblock_virt_alloc(x, 0);

We don't need the cast because memblock_virt_alloc() returns a void *.
The alignment value of zero tells memblock to use the default alignment,
which is SMP_CACHE_BYTES, the same value alloc_bootmem() uses.

We remove a number of NULL checks on the result of
memblock_virt_alloc(). That is because memblock_virt_alloc() will panic
if it can't allocate, in exactly the same way as alloc_bootmem(), so the
NULL checks are and always have been redundant.

The memory returned by memblock_virt_alloc() is already zeroed, so we
remove several memsets of the result of memblock_virt_alloc().

Finally we convert a few uses of __alloc_bootmem(x, y, MAX_DMA_ADDRESS)
to just plain memblock_virt_alloc(). We don't use memblock_alloc_base()
because MAX_DMA_ADDRESS is ~0ul on powerpc, so limiting the allocation
to that is pointless, 16XB ought to be enough for anyone.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Newer POWER designs do not implement PCI I/O space, so we
expect to see a number of these.

Reduce the severity of the warning so it doesn't mask other
real issues.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit 0b0b0893 "of/pci: Fix the conversion of IO ranges into IO
resources" changed the behaviour of of_pci_range_to_resource().

Previously it simply populated the resource based on the arguments. Now
it calls pci_register_io_range() and pci_address_to_pio(). These both
have two implementations depending on whether PCI_IOBASE is defined,
which it is not for powerpc.

Further complicating matters, both routines are weak, and powerpc
implements it's own version of one - pci_address_to_pio(). However
powerpc's implementation depends on other initialisations which are done
later in boot.

The end result is incorrectly initialised IO space. Often we can get
away with that, because we don't make much use of IO space. However
virtio requires it, so we see eg:

  pci_bus 0000:00: root bus resource [io  0xffff] (bus address [0xffffffffffffffff-0xffffffffffffffff])
  PCI: Cannot allocate resource region 0 of device 0000:00:01.0, will remap
  virtio-pci 0000:00:01.0: can't enable device: BAR 0 [io  size 0x0020] not assigned

The simplest fix for now is to just stop using of_pci_range_to_resource(),
and open-code the original implementation, that's all we want it to do.

Fixes: 0b0b0893 ("of/pci: Fix the conversion of IO ranges into IO resources")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

pci_bus_find_capability() is decleared in pci.h, so it is not necessary to do
it again.

This patch removes it.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Since the logic to reset PCI secondary bus by PCI config register
PCI_BRIDGE_CTL_BUS_RESET is included in pci_reset_secondary_bus(), we
needn't implement another one.

Remove the duplicate implementation and call pci_reset_secondary_bus().
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Move the devspec OF attribute to PCI common code's set of device attributes
since it's not architecture dependent.  As a side effect microblaze and
powerpc no longer need to use pcibios_add_platform_entries().

[bhelgaas: fold in #include for compile error]
Link: https://lkml.kernel.org/r/alpine.LFD.2.11.1404141101500.1529@denkbrettSigned-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch updates the implementation of pci_process_bridge_OF_ranges to use
the of_pci_range_parser helpers.
Signed-off-by: NAndrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The problem was initially reported by Wendy who tried pass through
IPR adapter, which was connected to PHB root port directly, to KVM
based guest. When doing that, pci_reset_bridge_secondary_bus() was
called by VFIO driver and linkDown was detected by the root port.
That caused all PEs to be frozen.

The patch fixes the issue by routing the reset for the secondary bus
of root port to underly firmware. For that, one more weak function
pci_reset_secondary_bus() is introduced so that the individual platforms
can override that and do specific reset for bridge's secondary bus.
Reported-by: NWendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

These interfaces:

  pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
  pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)

took a pci_dev, but they really depend only on the pci_bus.  And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:

  pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
  pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)

In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.

[bhelgaas: changelog]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

All the callers of irq_create_of_mapping() pass the contents of a struct
of_phandle_args structure to the function. Since all the callers already
have an of_phandle_args pointer, why not pass it directly to
irq_create_of_mapping()?
Signed-off-by: NGrant Likely <grant.likely@linaro.org>
Acked-by: NMichal Simek <monstr@monstr.eu>
Acked-by: NTony Lindgren <tony@atomide.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>

struct of_irq and struct of_phandle_args are exactly the same structure.
This patch makes the kernel use of_phandle_args everywhere. This in
itself isn't a big deal, but it makes some follow-on patches simpler.
Signed-off-by: NGrant Likely <grant.likely@linaro.org>
Acked-by: NMichal Simek <monstr@monstr.eu>
Acked-by: NTony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The OF irq handling code has been overloading the term 'map' to refer to
both parsing the data in the device tree and mapping it to the internal
linux irq system. This is probably because the device tree does have the
concept of an 'interrupt-map' function for translating interrupt
references from one node to another, but 'map' is still confusing when
the primary purpose of some of the functions are to parse the DT data.

This patch renames all the of_irq_map_* functions to of_irq_parse_*
which makes it clear that there is a difference between the parsing
phase and the mapping phase. Kernel code can make use of just the
parsing or just the mapping support as needed by the subsystem.

The patch was generated mechanically with a handful of sed commands.
Signed-off-by: NGrant Likely <grant.likely@linaro.org>
Acked-by: NMichal Simek <monstr@monstr.eu>
Acked-by: NTony Lindgren <tony@atomide.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Based on a patch by Jon Mason (see URL below).

All users of pcie_bus_configure_settings() pass arguments of the form
"bus, bus->self->pcie_mpss".  The "mpss" argument is redundant since we
can easily look it up internally.  In addition, all callers check
"bus->self" for NULL, which we can also do internally.

This patch simplifies the interface and the callers.  No functional change.

Reference: http://lkml.kernel.org/r/1317048850-30728-2-git-send-email-mason@myri.comSigned-off-by: NBjorn Helgaas <bhelgaas@google.com>

Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

pci_read_bridge_bases() already checks if the PCI bus is root
bus or not, so we needn't do same check in pcibios_fixup_bus()
and just remove it.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Address some of the trivial sparse warnings in arch/powerpc.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When EEH error happens to one specific PE, the device drivers
of its attached EEH devices (PCI devices) are checked to see
the further action: reset with complete hotplug, or reset without
hotplug. However, that's not enough for those PCI devices whose
drivers can't support EEH, or those PCI devices without driver.
So we need do so-called "partial hotplug" on basis of PCI devices.
In the situation, part of PCI devices of the specific PE are
unplugged and plugged again after PE reset.

The patch changes pcibios_add_pci_devices() so that it can support
full hotplug and so-called "partial" hotplug based on device-tree
or real hardware. It's notable that pci_of_scan.c has been changed
for a bit in order to support the "partial" hotplug based on dev-tree.

Most of the generic code already supports that, we just need to
plumb it properly on our side.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>