This device is not a serial port, but a virtual CD-ROM device. For
example with my Novatel MC950D:

lsusb -v -d 1410:5010 | grep InterfaceClass
      bInterfaceClass         8 Mass Storage

After some time (ca. 5min) or if virtual CD is ejected, device id
changes to 1410:4400:

% lsusb -v -d 1410:4400 | grep InterfaceClass
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceClass       255 Vendor Specific Class

Variable name says that 0x5010 is a Novatel U727, but searching in
internet shows, that this device also provides virtual CD that should be
ejected before use. Product id for serial port in this case is 0x4100.
Signed-off-by: NEugeniy Meshcheryakov <eugen@debian.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes ordering problems with entries in unusual_devs.h.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch below is a necessary workaround to support the Zoom Telephonics Model 3095F V.92 USB Mini External modem, which fails to initialise properly during normal probing thus:

May  3 22:53:00 imcfarla kernel: drivers/usb/class/cdc-acm.c: Zero length descriptor references
May  3 22:53:00 imcfarla kernel: cdc_acm: probe of 5-2:1.0 failed with error -22

Adding the patch below causes the probing section to be skipped, and the modem
then initialises correctly.
Signed-off-by: NIain McFarlane <iain@imcfarla.homelinux.net>
Acked-by: NOliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

the proposed patch allows the ET502HS HDSPA modem to be handled by the
"option" driver. It has been tested for 1 month and works reliably (no
oopses, no hangs, 300KB/s throughput).
Signed-off-by: NMauro Andreolini <andreoli@weblab.ing.unimo.it>
Signed-off-by: NMatthias Urlichs <matthias@urlichs.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The attached patch allows to bypass the ZeroCD mechanism for the ET502HS
HDSPA modem, so that it can be mounted as a network device.
Signed-off-by: NMauro Andreolini <andreoli@weblab.ing.unimo.it>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/usb/host/ohci-sm501.c:93:24: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3254:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3267:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3277:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3285:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3293:9: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix printk format warnings in isp1760 (in linux-next):

next-20080430/drivers/usb/host/isp1760-hcd.c:994: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
next-20080430/drivers/usb/host/isp1760-hcd.c:1092: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As reported by Magnus Boman <captain.magnus@opensuse.org>

Cc: Magnus Boman <captain.magnus@opensuse.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1087d) fixes a long-standing problem in usbcore: Device,
interface, and endpoint attributes aren't added until _after_ the
creation uevent has already been broadcast.

Unfortunately there are a few attributes which cannot be created that
early.  The "descriptors" attribute is binary and so must be created
separately.  The power-management attributes can't be created until
the dev/power/ group exists.  And the interface string can vary from
one altsetting to another, so it has to be created dynamically.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This should work on a KRZR K1m, and some other Motorola phones that do
not use the "standard" cdc ACM protocol to talk to USB hosts.
Tested-by: NJeff Garzik <jeff@garzik.org>
Cc: Jiang Dejun <a5652c@motorola.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes bug #10627 which caused the compilation error below.

  CC [M]  drivers/usb/c67x00/c67x00-ll-hpi.o
  drivers/usb/c67x00/c67x00-ll-hpi.c: In function `ll_recv_msg':
  drivers/usb/c67x00/c67x00-ll-hpi.c:243: erreur: `HZ' undeclared (first use in this function)
  drivers/usb/c67x00/c67x00-ll-hpi.c:243: erreur: (Each undeclared identifier is reported only once
  drivers/usb/c67x00/c67x00-ll-hpi.c:243: erreur: for each function it appears in.)
Signed-off-by: NFernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add ThinkOptics WavIt to cp2101 device table
Signed-off-by: NBernhard Beck <kernel@goodcoffee.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The file drivers/usb/serial/iuu_phoenix.c uses "int" for flags.  This can
cause hard to find bugs on some architectures.  This patch converts the flags
to use "long" instead.

This bug was discovered by doing an allyesconfig make on the -rt kernel where
checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Sparc doesn't have some of the OF interfaces this driver
wants to use.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Gadget tells controller driver to ignore Clear-Feature(HALT_ENDPOINT)
Signed-off-by: NDavid Lopo <lopo.david@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Given that the bulk of the Kconfig file is enclosed in "if USB_ATM",
remove the unnecessary dependencies.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1084b) fixes the way uhci-hcd handles polling and
remote wakeups for its root hubs.  When remote wakeup is disabled,
neither interrupts nor polling should be enabled during a root-hub
suspend.  Likewise, if interrupts are enabled during suspend then
polling isn't needed.

Furthermore the EGSM (Enter Global Suspend Mode) bit shouldn't be set
in the Command register unless remote wakeup is enabled.  Apparently
some controllers will issue a remote-wakeup interrupt whenever EGSM
is on, even if Resume-Detect interrupts are supposedly disabled.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch (as1086) works around a bogus "uninitialized variable"
warning generated by some versions of GCC.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds HCD support for the Cypress c67x00 family of devices.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch add the core driver for the c67x00 USB OTG controller.  The core
driver is responsible for the platform bus binding and creating either
USB HCD or USB Gadget instances for each of the serial interface engines
on the chip.

This driver does not directly implement the HCD or gadget behaviours; it
just controls access to the chip.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the low level support code for the Cypress c67x00 family of
OTG controllers.  The low level code is responsible for register access and
implements the software protocol for communicating with the 16bit
microcontroller inside the c67x00 device.

Communication is done over the HPI interface (16bit SRAM-like parallel bus).
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The following patch fixes a [probable] copy & paste mistake in
airprime.c. Instead of unlocking an acquired mutex, the actual
code tries to lock it again.
Signed-off-by: NLeonardo Chiquitto <lchiquitto@novell.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/usb/storage/unusual_devs.h lists the address
linux-usb-devel@lists.sourceforge.net for patches to that file. This
address results in a bounce and a pointer to vger. This patch updates
the address in the header file.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add more usb device ids to the ftdi driver.

From: Peter Mack <Peter.Mack@scs-ptc.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When I used ohci-sm501, hcd_alloc_coherent() in map_urb_for_dma() is not
called, because usb_sg_init() always sets URB_NO_TRANSFER_DMA_MAP.

dmesg (CONFIG_USB_STORAGE_DEBUG enabled):

usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code -75; transferred 0/36
usb-storage: -- babble
usb-storage: Bulk data transfer result 0x3
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x2
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Initialize timer earlier so if an error occurs allocating USB request
or buffer request (zero_bind) Gadget Zero will not hang trying to
delete an uninitialized timer (zero_unbind).
Signed-off-by: NDavid Lopo <lopo.david@gmail.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Minor updates to "Gadget Zero".

 - Primarily these are whitespace updates to address the fact that since
   this was written, Documentation/CodingStyle was changed to disapprove
   of parts of the original coding style.

 - Update a few comments that weren't quite correct, notably mentioning
   the "autoresume" module parameter.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Based on a patch from <Aurel.Thomi@ruag.com>, this makes the
CDC-ACM support in the serial gadget handle the SET_LINE_CODING
and SET_CONTROL_LINE_STATE requests ... which should improve
interop with at least MS-Windows "usbser.sys" if not some other
ACM host drivers.

It also adds a few REVISIT comments where this code plays a bit
loose with the CDC ACM spec.  If this were used to hook up to a
real RS232 or modem link, those places would need a bit of work.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds pxa27x udc driver to support USB peripherals on pxa27x chips.

The driver is compatible with: Gadget Zero, the File Storage
gadget, and the Ethernet gadget (only in CDC subset mode).

The driver can't properly support multiple interfaces, because
of hardware bugs without possible workaround.  That means no
RNDIS support from g_ether, and no CDC ACM support in g_serial.
Signed-off-by: NRobert Jarzmik <rjarzmik@free.fr>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

FIX_CAPACITY is all that's needed.


Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The test for an mos7840_set_uart_reg() error return value only works when
status is signed. propagate its error value.
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Cc: SL Baur <steve@xemacs.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Minor cleanup to the "usbtest" driver, mostly to resolve a regression:
all the important diagnostics were at KERN_DEBUG, so that when the
"#define DEBUG" was removed from the top of that file it stopped
providing diagnostics.  Fix by using KERN_ERROR.  Also:

 - Stop using the legacy dbg() calls
 - Simplify the internal debug macros
 - Correct some test descriptions:
	* Test #10 subcase 7 should *always* stall
	* Test #10 subcase 8 *may* stall
 - Diagnostic about control queue test failures is more informative
 - Fix some whitespace "bugs"

And add a warning about the rude interaction between usbfs ioctl()
and khubd during device disconnect ... don't unplug a device under
test, that will wedge.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1088) adds an unusual_devs entry for Samsung's YP-U3.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes the needlessly global onetouch_release_input() static.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If USB storage is built-in but input subsystem is made modular then
OneTouch button functionality can not be selected.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NDaniel Walker <dwalker@mvista.com>
Acked-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver has been written from scratch and supports the ISP1760. ISP1761
might (should) work as well but the OTG isn't supported. Also ISO packets are
not. However, it works on my little PowerPC board.
Signed-off-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>