The PXA SPI driver uses PXA platform specific private DMA implementation
which does not work on non-PXA platforms. In order to use this driver on
other platforms we break out the private DMA implementation into a separate
file that gets compiled only when CONFIG_SPI_PXA2XX_PXADMA is set. The DMA
functions are stubbed out if there is no DMA implementation selected (i.e
we are building on non-PXA platform).

While we are there we can kill the dummy DMA bits in pxa2xx_spi.h as they
are not needed anymore for CE4100.

Once this is done we can add the generic DMA engine support to the driver
that allows usage of any DMA controller that implements DMA engine API.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NLu Cao <lucao@marvell.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

SPI_GPIO_NO_MOSI and SPI_GPIO_NO_MISO flags are type casted to unsigned
long, yet, they are to be stored in an unsigned int field in the
spi_gpio_platform_data structure.

This leads to the following warning during compilation on 64 bits systems:
warning: large integer implicitly truncated to unsigned type [-Woverflow]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Convert clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare() respectively in order to support the common clk
framework. Otherwise we get warnings on the console as the clock is not
prepared before it is enabled.

In addition we must cache the maximum clock rate to drv_data->max_clk_rate
at probe time because clk_get_rate() cannot be called in tasklet context.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The spi-pxa2xx-pci glue driver had to implement pxa_ssp_request()/free() in
order to support the spi-pxa2xx platform driver. Since the ACPI enabled
platforms can use the same platform driver we would need to implement
pxa_ssp_request()/free() in some central place that can be shared by the
ACPI and PCI glue code.

Instead of doing that we can make pxa_ssp_request()/free() to be available
only when CONFIG_ARCH_PXA is set. On other arches these are being stubbed
out in preference to passing the ssp_device from the platform data
directly.

We also change the SPI bus number to be taken from ssp->port_id instead of
platform device id. This way the supporting code that passes the ssp can
decide the number (or it can set it to the same as pdev->id).
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This will allow to use gpio for chip select with no modification in the
driver binding

When use the cs-gpios, the gpio number will be passed via the cs_gpio field
and the number of chip select will automatically increased with max(hw cs, gpio cs).

So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:

cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;

Then it should be configured so that num_chipselect = 4 with the
following mapping:

cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
[grant.likely: fixed up type of cs count so min() can do type checking]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Some platforms need the pendown GPIO debounce time setting programmed.
Since the pendown GPIO is handled by the driver, the debounce time
should also be handled along with the pendown GPIO request.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Tegra20/Tegra30 supports the spi interface through its SLINK
controller. Add spi driver for SLINK controller.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Remove non-UAPI Kbuild files that have become empty as a result of UAPI
disintegration.  They used to have only header-y lines in them and those have
now moved to the Kbuild files in the corresponding uapi/ directories.

Possibly these should not be removed but rather have a comment inserted to say
they are intentionally left blank.  This would make it easier to add generated
header lines in future without having to restore the infrastructure.

Note that at this point not all the UAPI disintegration parts have been merged,
so it is likely that more empty Kbuild files will turn up.

It is probably necessary to make the files non-empty to prevent the patch
program from automatically deleting them when it reduces them to nothing.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Delete soon-obsolete e-mail address.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NMichael Kerrisk <mtk.manpages@gmail.com>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

These parts will be used by the MXS SPI driver too.
Signed-off-by: NMarek Vasut <marex@denx.de>
Acked-by: NChris Ball <cjb@laptop.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Pull out the MMC clock configuration function and make it
into SSP clock configuration function, so it can be used by
the SPI driver too.
Signed-off-by: NMarek Vasut <marex@denx.de>
Acked-by: NChris Ball <cjb@laptop.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Abstract out the common part of private data shared between MMC
and SPI. These shall later allow to use common clock configuration
function.
Signed-off-by: NMarek Vasut <marex@denx.de>
Acked-by: NChris Ball <cjb@laptop.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add missing register bits and registers into mxs-spi.h .
These will be used by the SPI driver.

Based on previous attempt by:
Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Acked-by: NChris Ball <cjb@laptop.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since the SSP controller can act as both SPI and MMC host,
renaming the enum to properly reflect the naming seems
appropriate.

Based on previous attempt by:
Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Acked-by: NChris Ball <cjb@laptop.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Move the definitions into separate file so separate SPI driver can be
implemented. The SSP controller in MXS can act both as a MMC host and
as a SPI host.

Based on previous attempt by:
Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Acked-by: NChris Ball <cjb@laptop.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Sebastian Zenker reported that driver swaps x and y samples when the
touchscreen leads are connected in accordance with the datasheet
specification.  Transposed axis can be typically corrected by touch
screen calibration however this bug also negatively influences touch
pressure measurements.

Add an option to correct x and y axis.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Reported-and-tested-by: NSebastian Zenker <sebastian.zenker@gmx.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The AT86RF231 is a feature rich, low-power 2.4 GHz radio transceiver
designed for industrial and consumer ZigBee/IEEE 802.15.4, 6LoWPAN,
RF4CE and high data rate 2.4 GHz ISM band applications.

This patch adds support for the Atmel RF230/231 radio transceivers.
Signed-off-by: NAlexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add pxa910-ssp into ssp_id_table, and fix pxa-ssp compiling issue
under mach-mmp architect.
Signed-off-by: NQiao Zhou <zhouqiao@marvell.com>
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds dmaengine supporting using sh_dma driver. The module
receives data by DMAC, it also needs TX DMAC to generate SPI's clocks.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Remove now redundant tclk from SPI platform data. This makes the platform
data empty, so remove it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Fix kernel-doc warning in spi.h (copy/paste):

Warning(include/linux/spi/spi.h:365): No description found for parameter 'unprepare_transfer_hardware'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Updated the generic SPI EEPROM driver AT25 for support of an additional address
bit in the instruction byte. Certain EEPROMS have a size that is larger than the
number of address bytes would allow (e.g. like M95040 from ST that has 512 Byte
size but uses only one address byte (A0 to A7) for addressing.) For the extra
address bit (A8, A16 or A24) bit 3 of the instruction byte is used. This
instruction bit is normally defined as don't care for other AT25 like chips.
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NIvo Sieben <meltedpianoman@gmail.com>
Acked-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The <linux/device.h> header includes a lot of stuff, and
it in turn gets a lot of use just for the basic "struct device"
which appears so often.

Clean up the users as follows:

1) For those headers only needing "struct device" as a pointer
in fcn args, replace the include with exactly that.

2) For headers not really using anything from device.h, simply
delete the include altogether.

3) For headers relying on getting device.h implicitly before
being included themselves, now explicitly include device.h

4) For files in which doing #1 or #2 uncovers an implicit
dependency on some other header, fix by explicitly adding
the required header(s).

Any C files that were implicitly relying on device.h to be
present have already been dealt with in advance.

Total removals from #1 and #2: 51.  Total additions coming
from #3: 9.  Total other implicit dependencies from #4: 7.

As of 3.3-rc1, there were 110, so a net removal of 42 gives
about a 38% reduction in device.h presence in include/*
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

Current sh-hspi had used platform-specific speed.
This patch remove it, and use spi_transfer specific speed.
It removes unnecessary flags from struct sh_hspi_info,
but struct sh_hspi_info is still exist, since sh-hspi needs
platform info in the future.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The loop count i traverses for ntrans which is unsigned
so make the loop count i also unsigned.

Fix the below warning
In file included from drivers/spi/spi-omap2-mcspi.c:38:
include/linux/spi/spi.h: In function 'spi_message_alloc':
include/linux/spi/spi.h:556: warning: comparison between signed and unsigned integer expressions

Cc: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds SuperH HSPI driver.
It is still prototype driver, but has enough function at this point.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This rips the message queue in the PL022 driver out and pushes
it into (optional) common infrastructure. Drivers that want to
use the message pumping thread will need to define the new
per-messags transfer methods and leave the deprecated transfer()
method as NULL.

Most of the design is described in the documentation changes that
are included in this patch.

Since there is a queue that need to be stopped when the system
is suspending/resuming, two new calls are implemented for the
device drivers to call in their suspend()/resume() functions:
spi_master_suspend() and spi_master_resume().

ChangeLog v1->v2:
- Remove Kconfig entry and do not make the queue support optional
  at all, instead be more agressive and have it as part of the
  compulsory infrastructure.
- If the .transfer() method is implemented, delete print a small
  deprecation notice and do not start the transfer pump.
- Fix a bitrotted comment.
ChangeLog v2->v3:
- Fix up a problematic sequence courtesy of Chris Blair.
- Stop rather than destroy the queue on suspend() courtesy of
  Chris Blair.
Signed-off-by: NChris Blair <chris.blair@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

spi.h now only contains the definition of the platform data structure
for the driver in spi-s3c24xx.c . Therefore it does not need to stay
in include/mach but can instead live in linux/spi/s3c24xx.h .
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch introduces the module_spi_driver macro which is a convenience macro
for SPI driver modules similar to module_platform_driver. It is intended to be
used by drivers which init/exit section does nothing but register/unregister
the SPI driver. By using this macro it is possible to eliminate a few lines of
boilerplate code per SPI driver.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The regulator support in the l4f00242t03 is very non-idiomatic.  Rather
than requesting the regulators based on the device name and the supply
names used by the device the driver requires boards to pass system
specific supply names around through platform data.  The driver also
conditionally requests the regulators based on this platform data, adding
unneeded conditional code to the driver.

Fix this by removing the platform data and converting to the standard
idiom, also updating all in tree users of the driver.  As no datasheet
appears to be available for the LCD I'm guessing the names for the
supplies based on the existing users and I've no ability to do anything
more than compile test.

The use of regulator_set_voltage() in the driver is also problematic,
since fixed voltages are required the expectation would be that the
voltages would be fixed in the constraints set by the machines rather than
manually configured by the driver, but is less problematic.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There's no in-tree users, and bus notifiers are more generic anyway.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Remove the #define GEN_74X164_GPIO_COUNT since it's only used in
one place and it's meaning is obvious.  Also remove the #define
GEN_74X164_DRIVER_NAME and use spi->modalias to set the gpio chip's
label and the string "74x164" for the driver name.

Reorder the code slightly to remove the need to prototype
gen_74x164_set_value.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Currently the simple SPI I/O operations all take pointers to u8 * buffers
to operate on. This creates needless type compatibility issues and the
underlying spi_transfer structure uses void pointers anyway so convert the
API over to take void pointers too.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Just set vref_mv in your platform config to use external vref. Otherwise
the internal one is used.
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

include/linux/dw_spi.h only includes driver internal data.  It doesn't
expose a platform_data configuration structure or similar (at least
nothing in-tree).  This patch moves the header into drivers/spi so
that the scope is limited to only the dw_spi_*.c driver files
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Feng Tang <feng.tang@intel.com>
Cc: spi-devel-general@lists.sourceforge.net

Currently, build on PPC dies with:
In file included from drivers/spi/dw_spi_mmio.c:16:
include/linux/spi/dw_spi.h:147: error: field ‘tx_sgl’ has incomplete type
include/linux/spi/dw_spi.h:149: error: field ‘rx_sgl’ has incomplete type

Add linux/scatterlist.h include to dw_spi.h, because we need to know
the contents of the structure.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Discussions:

http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26748.html

Introduce a driver for the Texas Instruments TSC2005 touchscreen
controller (http://focus.ti.com/docs/prod/folders/print/tsc2005.html).

The patch is based on a driver by Lauri Leukkunen, with modifications
by David Brownell, Phil Carmody, Imre Deak, Hiroshi DOYU, Ari Kauppi,
Tony Lindgren, Jarkko Nikula, Eero Nurkkala and Roman Tereshonkov.
Signed-off-by: NLauri Leukkunen <lauri.leukkunen@nokia.com>
[aaro.koskinen@nokia.com: patch description, rebasing & cleanup]
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
[ext-srikar.1.bhavanarayana@nokia.com: various fixes]
Signed-off-by: NSrikar <ext-srikar.1.bhavanarayana@nokia.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>