This patch fixes an issue seen with the realtek 8201 phy. This phy has a
problem with crossover detection and it needs to be disabled. The
problem only arises on certain switches. Therefore, a module parameter
has been added to allow enabling crossover detection if needed. The
default will be set to disabled.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds support for a new backoff algorithm for half duplex supported
in newer hardware.  The old method is will be designated as legacy mode.

Re-seeding random values for the backoff algorithms are performed when a
transmit has failed due to a maximum retry count (1 to 15, where max is
considered the wraparound case of 0).
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* remove changelog from source; its kept in git repository

* consolidate descriptor version tests using nv_optimized()

* consolidate NIC DMA start, stop and drain into
  nv_start_txrx(), nv_stop_txrx(), nv_drain_txrx()
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This critical patch fixes a mac address issue recently introduced.  If the
device's mac address was in correct order and the flag
NVREG_TRANSMITPOLL_MAC_ADDR_REV was set, during nv_remove the flag would get
cleared.  During next load, the mac address would get reversed because the
flag is missing.

As it has been indicated previously, the flag is cleared across a low power
transition.  Therefore, the driver should set the mac address back into the
reversed order when clearing the flag.

Also, the driver should set back the flag after a low power transition to
protect against kexec command calling nv_probe a second time.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Cc: "Yinghai Lu" <yhlu.kernel@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

a) if you initialize something with le32_to_cpu(...), then |= it
with host-endian and feed to cpu_to_le32(), it's most definitely
*not* __le32.  As sparse would've told you...

b) the whole sequence is |= cpu_to_le32(host-endian constant)
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

While using netconsole on forcedeth, lockdep noticed the following locking
bug:

=================================
[ INFO: inconsistent lock state ]
2.6.24-rc6 #6Signed-off-by: NIngo Molnar <mingo@elte.hu>
---------------------------------
inconsistent {softirq-on-W} -> {in-softirq-W} usage.
udevd/719 [HC0[0]:SC1[1]:HE1:SE0] takes:
 (_xmit_ETHER){-+..}, at: [<c043062e>] dev_watchdog+0x1c/0xb9
{softirq-on-W} state was registered at:
  [<c0147f67>] mark_held_locks+0x4e/0x66
  [<c014810e>] trace_hardirqs_on+0xfe/0x136
  [<c048ae63>] _spin_unlock_irq+0x22/0x42
  [<c02ec617>] nv_start_xmit_optimized+0x347/0x37a
  [<c042c80d>] netpoll_send_skb+0xa4/0x147
  [<c042d4a6>] netpoll_send_udp+0x238/0x242
  [<c02f44f6>] write_msg+0x6d/0x9b
  [<c012c129>] __call_console_drivers+0x4e/0x5a
  [<c012c18c>] _call_console_drivers+0x57/0x5b
  [<c012c2dd>] release_console_sem+0x11c/0x1b9
  [<c012caeb>] register_console+0x1eb/0x1f3
  [<c06ae673>] init_netconsole+0x119/0x15f
  [<c069149b>] kernel_init+0x147/0x294
  [<c01058cb>] kernel_thread_helper+0x7/0x10
  [<ffffffff>] 0xffffffff
irq event stamp: 950
hardirqs last  enabled at (950): [<c048ae63>] _spin_unlock_irq+0x22/0x42
hardirqs last disabled at (949): [<c048aaf7>] _spin_lock_irq+0xc/0x38
softirqs last  enabled at (0): [<c012a29c>] copy_process+0x375/0x126d
softirqs last disabled at (947): [<c0106d43>] do_softirq+0x61/0xc6

other info that might help us debug this:
no locks held by udevd/719.

stack backtrace:
Pid: 719, comm: udevd Not tainted 2.6.24-rc6 #6
 [<c0105c46>] show_trace_log_lvl+0x12/0x25
 [<c01063ec>] show_trace+0xd/0x10
 [<c010670c>] dump_stack+0x57/0x5f
 [<c0147505>] print_usage_bug+0x10a/0x117
 [<c0147c38>] mark_lock+0x121/0x402
 [<c01488b6>] __lock_acquire+0x3d1/0xb64
 [<c0149405>] lock_acquire+0x4e/0x6a
 [<c048a99b>] _spin_lock+0x23/0x32
 [<c043062e>] dev_watchdog+0x1c/0xb9
 [<c0133e4a>] run_timer_softirq+0x133/0x193
 [<c0130907>] __do_softirq+0x78/0xed
 [<c0106d43>] do_softirq+0x61/0xc6
 =======================
eth1: link down

The fix is to disable/restore irqs instead of disable/enable.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This timer doesn't need to run at precise times, so round it to a whole
second to decrease wakeups.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This is a critical patch which adds a workaround for a HW bug. The patch
will limit the number of outstanding tx packets to 16. Otherwise, the HW
could send out packets with bad checksums.

The driver will still setup the tx packets into the ring, however, will
only set the Valid bit on 16 packets at a time.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

New chipsets introduced variant Rx FIFO sizes that need to be taken into
account when setting up the tx pause watermarks. This patch introduces
the new device feature flags based on a version and implements the new
watermarks.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch supports a new fix in hardware regarding tx collisions. In
the cases where we are in autoneg mode and the link partner is in forced
mode, we need to setup the tx deferral register differently in order to
reduce collisions on the wire.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Various registers need to be preserved before resetting the device.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver needs to ack only the phy status bits that it is currently
handling and preserve the other bits for the other handlers. For
example, when reading/writing from the phy, it should not clear the link
change interrupt bit. This will cause a missing link change interrupt.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes the issue where the transmitter and receiver must be
restarted when applying new changes to certain registers.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch is a critical fix for MCP77 and MCP79 devices. The feature
flags were missing the define for correct mac address
(DEV_HAS_CORRECT_MACADDR).
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the case where no multicast addresses are requested to
be added to the multicast filter. The multicast mask must be set to all
1's instead of all 0's.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the tx pause enable watermark flags. The new values
where determined to be optimal during testing.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the copyright section to include 2007 and 2008.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver should inform the stack when checksum has been performed by
the HW when both IP and TCP (or UDP) checksum flags are indicated by HW.

Previously, it would also inform the stack when only IP checksum flag
was indicated by HW. This can cause data corruption when IP fragments
are used. The IP Identification field can wrap around and cause data
from new fragments to fill into older fragment slots with same IP Id.
The stack would then not perform TCP/UDP checksum (after re-assembly of
all fragments) since driver falsely stated it was already calculated.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the reset register definition from 0x3C to 0x34.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* misannotation: struct register_test members are actually host-endian
* bug: cpu_to_le64(n) >> 32 instead of cpu_to_le32(n >> 32) in setting
->bufhigh and similar for ->buflow (take low bits, _then_ convert to
little-endian, not the other way round).
* bug: setup_hw_rings() should not convert to little-endian at all (we
feed the result to writel(), not store in shared data structure), let
alone try to play with shifting and masking little-endian values.  Introduced
when setup_hw_rings() went in, screwed both 64bit case and the old code for
32bit rings it had replaced.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

For cards that initially have the MAC address stored in reverse order,
the forcedeth driver uses a flag to signal whether the address was
already corrected, so that it is not reversed again on a subsequent
probe.

Unfortunately this flag, which is stored in a register of the card,
seems to get lost during suspend, resulting in the MAC address being
reversed again. To fix that, the MAC address needs to be written back
in reversed order before we suspend and the flag needs to be reset.

The flag is still required because at least kexec will never write
back the reversed address and thus needs to know what state the card
is in.
Signed-off-by: NBjörn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a long boot delay in the forcedeth driver.  During initialization, the
timeout for the handshake between mgmt unit and driver can be very long.
The patch reduces the timeout by eliminating a extra loop around the
timeout logic.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9308Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Cc: Alex Howells <astinus@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds new device ids and features for mcp79 devices into the
forcedeth driver.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

pci_enable_msi() replaces the INTx irq number in pci_dev->irq with the
new MSI irq number.
The forcedeth driver did not update the copy in netdevice->irq and
parts of the driver used the stale copy.
See bugzilla.kernel.org, bug 9047.

The patch
- updates netdevice->irq
- replaces all accesses to netdevice->irq with pci_dev->irq.

The patch is against 2.6.23.1. IMHO suitable for both 2.6.23 and 2.6.24
Signed-Off-By: NManfred Spraul <manfred@colorfullife.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The merge of my previous fix to forcedeth.c,
bcb5febb, lost an important hunk.

We need to fix nv_rx_process_optimized() too, as it contains duplicate logic.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A copy of struct net_device_stats now lives in struct net_device,
making in-driver copies a waste of memory.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

main change:
* greatly improve per-NIC probe diagnostic output.  Similar to other
  net drivers, print out MAC address, PHY info, and various hardware and
  software flags that may be relevant.

other changes:
* similar to other net drivers, only print the initial version message
  when we have found at least one board.

* don't bother to print error message when pci_enable_device() fails,
  it will do so for us.

* use dev_printk() rather than printk() in nv_probe().  This gives
  use a standardized output similar to the rest of the kernel, and
  eliminates the need to manually print out PCI bus id.

* use DRV_NAME constant where appropriate

* clean struct pci_driver indentation
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

fix the forcedeth NAPI poll function to not emit this warning:

[  186.635916] WARNING: at net/core/dev.c:2166 net_rx_action()
[  186.641351]  [<c060d9f5>] net_rx_action+0x145/0x1b0
[  186.646191]  [<c011d752>] __do_softirq+0x42/0x90
[  186.650784]  [<c011d7c6>] do_softirq+0x26/0x30
[  186.655202]  [<c011db48>] local_bh_enable+0x48/0xa0
[  186.660055]  [<c06023e0>] lock_sock_nested+0xa0/0xc0
[  186.664995]  [<c065da16>] tcp_recvmsg+0x16/0xbc0
[  186.669588]  [<c013e94b>] __generic_file_aio_write_nolock+0x27b/0x520
[  186.676001]  [<c0601d75>] sock_common_recvmsg+0x45/0x70
[  186.681202]  [<c05ff5df>] sock_aio_read+0x11f/0x140
[  186.686054]  [<c015c086>] do_sync_read+0xc6/0x110
[  186.690735]  [<c012b9b0>] autoremove_wake_function+0x0/0x40
[  186.696280]  [<c060dcfc>] net_tx_action+0x3c/0xe0
[  186.700961]  [<c015c9c2>] vfs_read+0x132/0x140
[  186.705378]  [<c015cd41>] sys_read+0x41/0x70
[  186.709625]  [<c0102b66>] sysenter_past_esp+0x5f/0x89
[  186.714651]  =======================
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Log "no link during initialization" at KERN_INFO as it's not an error, and
occurs every time the interface comes up (when the forcedeth-phy-power-down
patch is applied).
Signed-off-by: NEd Swierk <eswierk@arastra.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is nicer than the MAC_FMT stuff.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the operations
	get-tx-csum
	get-sg
	get-tso
	get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.

This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.

The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case.  Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.

[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it.  The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.

[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.

In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.

The signature of the ->poll() call back goes from:

	int foo_poll(struct net_device *dev, int *budget)

to

	int foo_poll(struct napi_struct *napi, int budget)

The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract).  The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.

The napi_struct is to be embedded in the device driver private data
structures.

Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler.  Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.

With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.

Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.

[ Ported to current tree and all drivers converted.  Integrated
  Stephen's follow-on kerneldoc additions, and restored poll_list
  handling to the old style to fix mutual exclusion issues.  -DaveM ]
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noticed by Chuck Ebbert, commit c5e3ae88
introduced a copy-paste typo, as realtek phy is 0x732 and not 0x1c1. Obvious
fix below suggested by Ayaz Abdulla.
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If the forcedeth driver receives too much work in an interrupt, it
assumes it has a broken hardware with stuck IRQ.  It works around the
problem by disabling interrupts on the nic but makes a printk while
holding device spinlog - which isn't smart thing to do if you have
netconsole on the same nic.

This patch moves the printk's out of the spinlock protected area.

Without this patch the machine hangs hard.  With this patch everything
still works even when there is significant increase on CPU usage while
using the nic.
Signed-off-by: NTimo Jantunen <jeti@iki.fi>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function.  So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In older chipsets, the mac address was stored in reversed order.
However, in newer chipsets, the mac address is in correct order. This
patch takes those newer chipsets into account and does not rely on a
special bit setup by BIOS'.
Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch contains new device settings for MCP73 chipset.
Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>