Everything is covered either by fbc.lock or mm.stolen_lock, and
intel_fbc.c is already responsible for grabbing the appropriate locks
when it needs them.
Reviewed-by: NChris wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So don't grab the lock before calling the function.
Reviewed-by: NChris wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So release the lock earlier.
Reviewed-by: NChris wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make sure we're not going to have weird races in really weird cases
where a lot of different CRTCs are doing rendering and modesets at the
same time.

With this change and the stolen_lock from the previous patch, we can
start removing the struct_mutex locking we have around FBC in the next
patches.

v2:
 - Rebase (6 months later)
 - Also lock debugfs and stolen.
v3:
 - Don't lock a single value read (Chris).
 - Replace lockdep assertions with WARNs (Daniel).
 - Improve commit message.
 - Don't forget intel_pre_plane_update() locking.
v4:
 - Don't remove struct_mutex at intel_pre_plane_update() (Chris).
 - Add comment regarding locking dependencies (Chris).
 - Rebase after the stolen code rework.
 - Rebase again after drm-intel-nightly changes.
v5:
 - Rebase after the new stolen_lock patch.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4)
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Kill the extra intel_pre_plane_update() I accidentally added in

 commit 852eb00d
 Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
 Date:   Wed Jun 24 22:00:07 2015 +0300

    drm/i915: Try to make sure cxsr is disabled around plane
    enable/disable

This fixes a load of warnings from the frontbuffer tracking.

Testcase: igt/kms_frontbuffer_tracking/fbc-1p-rte
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch contains changes based on 2 updates to the spec:
Port PLL VCO restriction raised up to 6700.
Port PLL now needs DCO amp override enable for all VCO frequencies.

v2: Sonika's review comment addressed
	- dcoampovr_en_h variable not required
Based on a discussion with Siva, the following changes have been made.
	- replace dco_amp var with #define BXT_DCO_AMPLITUDE
	- set pll10 in a single assignment

v3:
Move DCO amplitude default value to i915_reg.h. Suggested by Siva.
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com> [v2]
[danvet: Spell out BUN since not everyone knows what this means.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Depending on the platform the port clock fed to the pipe can be the PLL's
post-divided fast clock rate or a /5 divided version of it. To make this
more obvious across the platforms calculate this port clock along with
the rest of the PLL parameters.

This is also needed by the next patch where we can reuse the CHV helper
for the BXT PLL HW readout code; so export the corresponding helper.

While at it also add a more descriptive name to the helpers and a
comment explaining what's being calculated.

No functional change.
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move the helper next to the PLL helpers of the other platforms for
clarity.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Although we have a fixed setting for the PLL9 and EBB4 registers, it
still makes sense to check them together with the rest of PLL registers.

While at it also remove a redundant comment about 10 bit clock enabling.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CxSR (or maxfifo on VLV/CHV) blocks somne changes to the plane control
register (enable bit at least, not quite sure about the rest). So in
order to have the plane enable/disable when we want we need to first
kick the hardware out of cxsr.

Unfortunateloy this requires some extra vblank waits. For the CxSR
enable after the plane update we should eventually use an async
vblank worker, but since we don't have that just do sync vblank
waits. For the disable case we have no choice but to do it
synchronously.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NClint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In order to get decnet memory self refresh residency on VLV, flip it
over to the new CHV way of doing things. VLV doesn't do PM5 or DDR DVFS
so it's a bit simpler.

I'm not sure the currently memory latency used for CHV is really
appropriate for VLV. Some further testing will probably be needed to
figure that out.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NClint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Turns out the VLV/CHV system agent doesn't understand memory
latencies, so trying to rely on the PND deadline mechanism is not
going to fly especially when DDR DVFS is enabled. Currently we try to
avoid the problems by lying to the system agent about the deadlines
and setting the FIFO watermarks to 8 cachelines. This however leads to
bad memory self refresh residency.

So in order to satosfy everyone we'll just give up on the deadline
scheme and program the watermarks old school based on the worst case
memory latency.

I've modelled this a bit on the ILK+ approach where we compute multiple
sets of watermarks for each pipe (PM2,PM5,DDR DVFS) and when merge thet
appropriate one later with the watermarks from other pipes. There isn't
too much to merge actually since each pipe has a totally independent
FIFO (well apart from the mess with the partially shared DSPARB
registers), but still decopuling the pipes from each other seems like a
good idea.

Eventually we'll want to perform the watermark update in two phases
around the plane update to avoid underruns due to the single buffered
watermark registers. But that's still in limbo for ILK+ too, so I've not
gone that far yet for VLV/CHV either.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NClint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Read out the current watermark settings from the hardware at driver init
time. This will allow us to compare the newly calculated values against
the currrent ones and potentially avoid needless WM updates.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NClint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Try to update the watermarks on the right side of the plane update. This
is just a temporary hack until we get the proper two part update into
place. However in the meantime this might have some chance of at least
working.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NClint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We cannot let IPS enabled with no plane on the pipe:

BSpec: "IPS cannot be enabled until after at least one plane has
been enabled for at least one vertical blank." and "IPS must be
disabled while there is still at least one plane enabled on the
same pipe as IPS." This restriction apply to HSW and BDW.

However a shortcut path on update primary plane function
to make primary plane invisible by setting DSPCTRL to 0
was leting IPS enabled while there was no
other plane enabled on the pipe causing flickerings that we were
believing that it was caused by that other restriction where
ips cannot be used when pixel rate is greater than 95% of cdclok.

v2: Don't mess with Atomic path as pointed out by Ville.

v3: Rebase after a long time and atomic path changes.
    Accept Ville suggestion of not check !fb

v4: Re-factore on dinq

Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85583
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NKenneth Graunke <kenneth@whitecape.org>
[danvet: Make it compile]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently we don't have any real indication when a pipe gets
enabled/disabled. Add some.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Avoid some 'switch (plane->type)' by storing the fronbuffer_bits in
intel_plane.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: use singular frontbuffer_bits in intel_plane since a plan can
only ever have one bit. Discussed with Ville on irc.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The registers and process differ from other platforms. If the hardware
was programmed incorrectly, this will return invalid cdclk values, which
should then cause reprogramming of the hardware.

v2(Matt): Return 19.2 MHz when DE PLL is disabled (Ville)
v3: Make less assumptions about the hardware state (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NBob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This way data is available as soon as the view is passed into the call chain.

v2: Store size in bytes instead of pages under the appropriate name. (Chris Wilson)

v3: Use uint64_t instead of size_t. (Daniel Vetter)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v2)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the new DRRS code it kinda sticks out, and we never managed to
get this to work well enough without causing issues. Time to wave
goodbye.

I've decided to keep the logic for programming the reduced clocks
intact, but everything else is gone. If anyone ever wants to resurrect
this we need to redo it all anyway on top of the frontbuffer tracking.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This typo lead to the crtc scaler getting enabled incorrectly and an
evantual state checker mismatch about the scaler_id.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I was momentarily confused until I've double-checked that these
functions really only compute state and don't update the hardware
state. They once did that, but since Ander's rework of the dpll
computation flow that's no longer the case.

Rename them to avoid further confusion.

Note that the ilk code already follows the compute_dpll naming scheme
for computing the actual register value. DDI code goes with _calc_,
but that is close enough.

Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

As there is no OLR to check, the check_olr() function is now a no-op and can be
removed.

For: VIZ-5115
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Reviewed-by: NTomas Elf <tomas.elf@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that everything above has been converted to use requests, intel_ring_begin()
can be updated to take a request instead of a ring. This also means that it no
longer needs to lazily allocate a request if no-one happens to have done it
earlier.

For: VIZ-5115
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Reviewed-by: NTomas Elf <tomas.elf@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Updated intel_ring_cacheline_align() to take a request instead of a ring.

For: VIZ-5115
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Reviewed-by: NTomas Elf <tomas.elf@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that all callers of i915_add_request() have a request pointer to hand, it is
possible to update the add request function to take a request pointer rather
than pulling it out of the OLR.

For: VIZ-5115
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Reviewed-by: NTomas Elf <tomas.elf@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Updated the display page flip code to do explicit request creation and
submission rather than relying on the OLR and just hoping that the request
actually gets submitted at some random point.

The sequence is now to create a request, queue the work to the ring, assign the
known request to the flip queue work item then actually submit the work and post
the request.

Note that every single flip function used to finish with
'__intel_ring_advance(ring);'. However, immediately after they return there is
now an add request call which will do the advance anyway. Thus the many
duplicate advance calls have been removed.

v2: Updated commit message with comment about advance removal.

v3: The request can now be allocated by the _sync() code earlier on. Thus the
page flip path does not necessarily need to allocate a new request, it may be
able to re-use one.

For: VIZ-5115
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Reviewed-by: NTomas Elf <tomas.elf@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The plan is to pass requests around as the basic submission tracking structure
rather than rings and contexts. This patch updates the i915_gem_object_sync()
code path.

v2: Much more complex patch to share a single request between the sync and the
page flip. The _sync() function now supports lazy allocation of the request
structure. That is, if one is passed in then that will be used. If one is not,
then a request will be allocated and passed back out. Note that the _sync() code
does not necessarily require a request. Thus one will only be created until
certain situations. The reason the lazy allocation must be done within the
_sync() code itself is because the decision to need one or not is not really
something that code above can second guess (except in the case where one is
definitely not required because no ring is passed in).

The call chains above _sync() now support passing a request through which most
callers passing in NULL and assuming that no request will be required (because
they also pass in NULL for the ring and therefore can't be generating any ring
code).

The exeception is intel_crtc_page_flip() which now supports having a request
returned from _sync(). If one is, then that request is shared by the page flip
(if the page flip is of a type to need a request). If _sync() does not generate
a request but the page flip does need one, then the page flip path will create
its own request.

v3: Updated comment description to be clearer about 'to_req' parameter (Tomas
Elf review request). Rebased onto newer tree that significantly changed the
synchronisation code.

v4: Updated comments from review feedback (Tomas Elf)

For: VIZ-5115
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Reviewed-by: NTomas Elf <tomas.elf@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The same dpll p2 divider selection is repeated three times in the
gen2-4 .find_dpll() functions. Factor it out.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The skylake scalers depend on the cdclk freq, but that frequency can
change during a modeset. So when a modeset happens calculate the new
cdclk in the atomic state. With the transitional helpers gone the
cached value can be used in the scaler, and committed after all
crtc's are disabled.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90874Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By making color key atomic there are no more transitional helpers.
The plane check function will reject the color key when a scaler is
active.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No need to repeatedly call update_watermarks, or update_fbc.
Down to a single call to update_watermarks in .crtc_enable
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that all planes are added during a modeset we can use the
calculated changes before disabling a plane, and then either commit
or force disable a plane before disabling the crtc.

The code is shared with atomic_begin/flush, except watermark updating
and vblank evasion are not used.

This is needed for proper atomic suspend/resume support.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Read out the initial state, and add a quirk to force add all planes
to crtc_state->plane_mask during initial commit. This will disable
all planes during the initial modeset.

The initial plane quirk is temporary, and will go away when hardware
readout is fully atomic, and the watermark updates in intel_sprite.c
are removed.

Changes since v1:
- Unset state->visible on !primary planes.
- Do not rely on the plane->crtc pointer in intel_atomic_plane,
  instead assume planes are invisible until modeset.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

All the checks in intel_modeset_checks are only useful when a modeset
occurs, because there is nothing to update otherwise.

Same for power/cdclk changes, if there is no modeset they are noops.

Unfortunately intel_modeset_pipe_config still gets called without
modeset, because atomic hw readout isn't done yet.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To allow them to be used in intel_set_mode.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is probably intended to be be done during vblank evasion.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The idea was good, but planes can have a fb even though
they're disabled. This makes the force argument useless
and always true, because only the commit function updates
state.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By passing crtc_state to the check_plane functions a lot of duplicated
code can be removed. There are still some transitional helper calls,
they will be removed later.

Changes since v1:
- Revert state->visible changes.
- Use plane->state->crtc instead of plane->crtc.
- Use drm_atomic_get_existing_crtc_state.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>