This patch includes support for the Intra-Site Automatic Tunnel
Addressing Protocol (ISATAP) per RFC4214. It uses the SIT
module, and is configured using extensions to the "iproute2"
utility. The diffs are specific to the Linux 2.6.24-rc2 kernel
distribution.

This version includes the diff for ./include/linux/if.h which was
missing in the v2.4 submission and is needed to make the
patch compile. The patch has been installed, compiled and
tested in a clean 2.6.24-rc2 kernel build area.
Signed-off-by: NFred L. Templin <fred.l.templin@boeing.com>
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sock_wake_async() performs a bit different actions
depending on "how" argument. Unfortunately this argument
ony has numerical magic values.

I propose to give names to their constants to help people
reading this function callers understand what's going on
without looking into this function all the time.

I suppose this is 2.6.25 material, but if it's not (or the
naming seems poor/bad/awful), I can rework it against the
current net-2.6 tree.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I keep getting this build error and couldn't find anyone fixing
it in archives. ...Maybe all net developers except me build
just SMP kernels :-).

In file included from include/net/sock.h:50,
                 from ipc/mqueue.c:35:
include/linux/pcounter.h: In function 'pcounter_add':
include/linux/pcounter.h:87: error: 'struct pcounter' has no
member named 'value'
make[1]: *** [ipc/mqueue.o] Error 1
make: *** [ipc] Error 2
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This decouples PARTOPEN from TCP-specific stream-states.

It thus addresses the FIXME.

The code has been checked with regard to dependency on PARTOPEN and FIN_WAIT1
states (to which PARTOPEN previously was mapped): there is no difference, as
PARTOPEN is always referred to directly (i.e. not via the mapping to TCP
state).
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This just generalises what was introduced by Eric Dumazet for the struct proto
inuse field in 286ab3d4:

    [NET]: Define infrastructure to keep 'inuse' changes in an efficent SMP/NUMA way.

Please look at the comment in there to see the rationale.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds several structs and definitions to ieee80211.h
to support 802.11n draft specifications.
As 802.11n depends on and extends the 802.11e standard in several issues,
there are also several definitions that belong to 802.11e.
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After this patch none of the netlink callback support anything
except the initial network namespace but the rtnetlink infrastructure
now handles multiple network namespaces.

Changes from v2:
- IPv6 addrlabel processing

Changes from v1:
- no need for special rtnl_unlock handling
- fixed IPv6 ndisc
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds IEEE80211_MAX_FRAME_LEN which is useful for drivers trying
to determine how much to allocate for their RX buffers.

It also updates the comment on IEEE80211_MAX_DATA_LEN based on revisions
in 802.11e.

IEEE80211_MAX_FRAG_THRESHOLD and IEEE80211_MAX_RTS_THRESHOLD are also
revised due to the new maximum frame size.
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rx_flags variable is redundant. Turning rx on/off is done
via setting the rx_np pointer.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The local_mac is managed by the network device, no need to keep a
spare copy and all the management problems that could cause.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the missing Kbuild entries and the missing Kbuild file
in include/linux/can for the CAN subsystem.
Signed-off-by: NOliver Hartkopp <oliver@hartkopp.net>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the use of plain integers instead of __u32 in a struct
that is visible from kernel space and user space.

Thanks to Sam Ravnborg for pointing out the wrong plain int usage.
Signed-off-by: NOliver Hartkopp <oliver@hartkopp.net>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the CAN broadcast manager (bcm) protocol.
Signed-off-by: NOliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: NUrs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the CAN raw protocol.
Signed-off-by: NOliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: NUrs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the CAN core functionality but no protocols or drivers.
No protocol implementations are included here.  They come as separate
patches.  Protocol numbers are already in include/linux/can.h.
Signed-off-by: NOliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: NUrs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a protocol/address family number, ARP hardware type,
ethernet packet type, and a line discipline number for the SocketCAN
implementation.
Signed-off-by: NOliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: NUrs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Key points of this patch are:

  - In case new SACK information is advance only type, no skb
    processing below previously discovered highest point is done
  - Optimize cases below highest point too since there's no need
    to always go up to highest point (which is very likely still
    present in that SACK), this is not entirely true though
    because I'm dropping the fastpath_skb_hint which could
    previously optimize those cases even better. Whether that's
    significant, I'm not too sure.

Currently it will provide skipping by walking. Combined with
RB-tree, all skipping would become fast too regardless of window
size (can be done incrementally later).

Previously a number of cases in TCP SACK processing fails to
take advantage of costly stored information in sack_recv_cache,
most importantly, expected events such as cumulative ACK and new
hole ACKs. Processing on such ACKs result in rather long walks
building up latencies (which easily gets nasty when window is
huge). Those latencies are often completely unnecessary
compared with the amount of _new_ information received, usually
for cumulative ACK there's no new information at all, yet TCP
walks whole queue unnecessary potentially taking a number of
costly cache misses on the way, etc.!

Since the inclusion of highest_sack, there's a lot information
that is very likely redundant (SACK fastpath hint stuff,
fackets_out, highest_sack), though there's no ultimate guarantee
that they'll remain the same whole the time (in all unearthly
scenarios). Take advantage of this knowledge here and drop
fastpath hint and use direct access to highest SACKed skb as
a replacement.

Effectively "special cased" fastpath is dropped. This change
adds some complexity to introduce better coveraged "fastpath",
though the added complexity should make TCP behave more cache
friendly.

The current ACK's SACK blocks are compared against each cached
block individially and only ranges that are new are then scanned
by the high constant walk. For other parts of write queue, even
when in previously known part of the SACK blocks, a faster skip
function is used (if necessary at all). In addition, whenever
possible, TCP fast-forwards to highest_sack skb that was made
available by an earlier patch. In typical case, no other things
but this fast-forward and mandatory markings after that occur
making the access pattern quite similar to the former fastpath
"special case".

DSACKs are special case that must always be walked.

The local to recv_sack_cache copying could be more intelligent
w.r.t DSACKs which are likely to be there only once but that
is left to a separate patch.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is going to replace the sack fastpath hint quite soon... :-)
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Policy table is implemented as an RCU linear list since we do not expect
large list nor frequent updates.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IPv4 and IPv6 hook values are identical, yet some code tries to figure
out the "correct" value by looking at the address family. Introduce NF_INET_*
values for both IPv4 and IPv6. The old values are kept in a #ifndef __KERNEL__
section for userspace compatibility.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support for network splice receive.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow caller to pass in a release function, there might be
other resources that need releasing as well. Needed for
network receive.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Samsung USB remotes (0419:0001) are rejected by kernel 2.6.23, because the
report descriptor from the remote contains a 48 bit HID report field. HID 1.11
states: Fields may span at most 4 bytes.

This patch, based on 2.6.23, fixes this by modifying the internal report
descriptor in hid-quirks.c. Additional user space support (e.g. LIRC) is
required to fetch the information from the hiddev interface.

The burden to reconstruct the data is moved into userspace (lirc through hiddev).
There is no need to set HID_QUIRK_HIDDEV quirk, as the device has also output
applications, which trigger the creation of hiddev device automatically.
Signed-off-by: NRobert Schedel <r.schedel@yahoo.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix a panic, by changing
	hidinput_mapping_quirks(,, unsigned long *bit,)
to
	hidinput_mapping_quirks(,, unsigned long **bit,)

The `bit' in this function is an out parameter.
Signed-off-by: NFengguang Wu <wfg@mail.ustc.edu.cn>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This removes ugly macros IS_* to distinguish devices that
need special handling in hid-input, and establish proper
quirks for them.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

BTC 8193 keyboard handles its scrollwheel in very non-standard way.
It produces two non-standard usages for scrolling up and down, in
both cases with postive value equaling to 1. We handle this by temporary
mapping, which we then catch in quirk event handler, and remap to
negative HWHEEL even in order to introduce correct behavior.

Also the button requires special mapping, as it triggers standard-violating
usage code.

Reported in kernel.org bugzilla #9385
Reported-by: NKir Kolyshkin <kir@sacred.ru>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch separates also the hid-input quirks that have to be
applied at the time the event occurs, so that the generic code
handling HUT-compliant devices is not messed up by them too much.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Currently, the handling of mapping between hid and input for devices
that don't conform to HUT 1.12 specification is very messy -- no per-device
handling, no blacklists, conditions on idVendor and idProduct placed
all over the code.

This patch moves all the device-specific input mapping to a separate
file, and introduces a blacklist-style handling for non-standard
device-specific mappings.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Genius KB-29E has broken report descriptor, which causes some of the
Consumer usages to appear incorrectly as Button usages. We fix it by
fixing the report descriptor before it is being parsed.

Also a few of the keys violate the HUT standard, so they need a special
handling. They currently fall into "Reserved" range as per HUT 1.12.
Reported-by: NSzekeres Istvan <szekeres@iii.hu>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This mouse distinguishes horizontal wheel from vertical by a special "pseudo
event" GenericDesktop.00b8, with values of 0 for vertical and 8 for horizontal
wheel. Because this event is supplied by the parser too late, we need to delay
a wheel event, wait for this one and send either REL_WHEEL or REL_HWHEEL to
input depending on the event value.
Signed-off-by: NPavel Troller <patrol@sinus.cz>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Preserve identifiers exposed in build and run time configuration though in
order not to break existing configurations.

This is in preparation for adding support for Apple aluminum USB keyboards.
Signed-off-by: NMichel Daenzer <michel@tungstengraphics.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

SCSI sg table allocation has a maximum size (of SCSI_MAX_SG_SEGMENTS,
currently 128) and this will cause a BUG_ON() in SCSI if something
tries an allocation over it.  This patch adds a size limit to the
chaining allocator to allow the specification of the maximum
allocation size for chaining, so we always chain in units of the
maximum SCSI allocation size.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

These DMA drain buffer implementations in drivers are pretty horrible
to do in terms of manipulating the scatterlist.  Plus they're being
done at least in drivers/ide and drivers/ata, so we now have code
duplication.

The one use case for this, as I understand it is AHCI controllers doing
PIO mode to mmc devices but translating this to DMA at the controller
level.

So, what about adding a callback to the block layer that permits the
adding of the drain buffer for the problem devices.  The idea is that
you'd do this in slave_configure after you find one of these devices.

The beauty of doing it in the block layer is that it quietly adds the
drain buffer to the end of the sg list, so it automatically gets mapped
(and unmapped) without anything unusual having to be done to the
scatterlist in driver/scsi or drivers/ata and without any alteration to
the transfer length.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

syslets (or other threads/processes that want io context sharing) can
set this to enforce sharing of io context.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

The io context sharing introduced a per-ioc spinlock, that would protect
the cfq io context lookup. That is a regression from the original, since
we never needed any locking there because the ioc/cic were process private.

The cic lookup is changed from an rbtree construct to a radix tree, which
we can then use RCU to make the reader side lockless. That is the performance
critical path, modifying the radix tree is only done on process creation
(when that process first does IO, actually) and on process exit (if that
process has done IO).

As it so happens, radix trees are also much faster for this type of
lookup where the key is a pointer. It's a very sparse tree.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Detach task state from ioc, instead keep track of how many processes
are accessing the ioc.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This is where it belongs and then it doesn't take up space for a
process that doesn't do IO.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch converts 'uptodate' arguments of no longer exported
interfaces, end_that_request_first/last, to 'error', and removes
internal conversions for it in blk_end_request interfaces.

Also, this patch removes no longer needed end_io_error().

Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NKiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>