- 27 8月, 2006 1 次提交
-
-
由 Hans de Goede 提交于
This patch contains 2 sets of fixes for the abituguru: 1) Much improved timeout handling, drasticly reducing the amount of timeout errors on some motherboards 2) Fix the exit paths in the bank1 sensor type detect code to always restore the original settings even on an error. Without this our special test settings could remain seriously confusing the system BIOS's setup menu. Both are very much related and are must haves, to avoid messing up the uguru CMOS settings. Detailed changes: - Much improved timeout / wait for status handling. Many thanks to Sunil Kumar, for all his testing, ideas and patches! The code now first busy waits, polling the uguru for the expected status as this usually succeeds pretty quickly (within 90 reads). To avoid unnecessary CPU burn in timeout conditions, the amount of busy waiting has been halved from previous versions (120 tries instead of 250). This is not a problem, because this version goes to sleep after 120 attemps for 1 jiffy and then tries again, it does this sleep and try again 5 times before finally giving up. This (almost?) completly removes the timeout errors some people have seen regulary. Apparently some older uguru versions sometimes are distracted for a (relatively) long time. This solves this. - These timeout errors not only occur in the sending address part of reading the uguru but also in the wait for read state, so errors in this state are now handled as retryable just like send address state errors and are only logged and reported to userspace if 3 executive tries fail. - Fix a very nasty bug in the bank1 sensor type detection code, where it would not restore the original settings in any of the error paths! - Since not successfully restoring the original settings can seriously confuse the system BIOS (hang when entering the relevant setup menu), we now try restoring them 3 times before giving up. Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 13 7月, 2006 1 次提交
-
-
由 Hans de Goede 提交于
Now that the abituguru driver is seeing some more widespread testing it has turned out that one the first generation of Abit uGuru motherboards, with uGuru revision 1, the autodetect bank1 sensor type code doesn't (always) work. This patch adds a module param to override the autodetect, and it adds validity checks for the value of the 2 other autodetection override module params. An example of howto use the new param can be found here: http://lm-sensors.org/wiki/Configurations/Abit/AN7Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 01 7月, 2006 1 次提交
-
-
由 Jörn Engel 提交于
Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
- 27 6月, 2006 1 次提交
-
-
由 Andreas Mohr 提交于
acquired (aquired) contiguous (contigious) successful (succesful, succesfull) surprise (suprise) whether (weather) some other misspellings Signed-off-by: NAndreas Mohr <andi@lisas.de> Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
- 23 6月, 2006 18 次提交
-
-
由 Rudolf Marek 提交于
This patch adds support for two new VID codes, supporting Intel mobile Core processors and new Conroe based platforms. Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Kaiwan N Billimoria 提交于
This driver implements support for the National Semiconductor LM70 temperature sensor. The LM70 temperature sensor chip supports a single temperature sensor. It communicates with a host processor (or microcontroller) via an SPI/Microwire Bus interface. Communication with the LM70 is simple: when the temperature is to be sensed, the driver accesses the LM70 using SPI communication: 16 SCLK cycles comprise the MOSI/MISO loop. At the end of the transfer, the 11-bit 2's complement digital temperature (sent via the SIO line), is available in the driver for interpretation. This driver makes use of the kernel's in-core SPI support. Signed-off-by: NKaiwan N Billimoria <kaiwan@designergraphix.com> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jean Delvare 提交于
Hardware monitoring chips don't have to be on the I2C bus. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Hans de Goede 提交于
One of my testers had a problem where the driver only saw 2 of the 4 fan sensors his uGuru has, this fixes this. -accept 0x40 (bit 6) being high as a valid fan sensor setting for all fans not just fan 1, I have a feeling this bit indicates whether or not a fan is actually connected . Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Hans de Goede 提交于
Fixes to the Abit uGuru driver as requested in review by Jean Delvare: - exactly calculate the sysfs_names array length using macro - use snprintf when generating names to double check that the sysfs_names array does not overflow. - use ARRAY_SIZE and / or defines to determine number of loops in for loops instead of using hardcoded values. - In abituguru_probe(), refactor the error path leaving a single call to kfree Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Hans de Goede 提交于
New hardware monitoring driver for the Abit uGuru Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Yuan Mu 提交于
Add missing data lock in w83792d driver to avoid unexpected data change. Signed-off-by: NYuan Mu <ymu@winbond.com.tw> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Yuan Mu 提交于
W83792D use pwm register low 4 bits to store PWM/DC value, bit 7 is used to store fan PWM/DC mode. The store_pwm function did not convert the pwm input correctly, so it may change the fan mode when new value is set. This fix the problem. Change the "index" value of pwm*_mode and pwm* SENSOR_ATTR to simplify code. Signed-off-by: NYuan Mu <ymu@winbond.com.tw> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jean Delvare 提交于
Fix a typo in the hdaps driver. Signed-off-by: NJean Delvare <khali@linux-fr.org> Acked-by: NRobert Love <rml@novell.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Rudolf Marek 提交于
Following patch trims the VID value to correct number of bits for each VRM. Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jean Delvare 提交于
Improve the help text for CONFIG_HWMON to let the users know how they pick the right hardware monitoring driver(s) for their system. Also fix a couple typos in the related documentation file and improve some parts a bit. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Charles Spirakis 提交于
Add support for the w83791d sensor chip. The w83791d hardware is somewhere between the w83781d and the w83792d and this driver code is derived from the code that supports those chips. Signed-off-by: NCharles Spirakis <bezaur@gmail.com> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jean Delvare 提交于
Update the list of systems supported by the hdaps driver: * Add the "ThinkPad Z60m" entry, reported by Arkadiusz Miskiewicz. * Add the "ThinkPad H" entry, reported by Frank Gevaerts for some ThinkPad R52 models (1846AQG). * Drop the "ThinkPad X41 Tablet" entry, which looks redundant to me. And a comment update for good measure. Signed-off-by: NJean Delvare <khali@linux-fr.org> Cc: Arkadiusz Miskiewicz <arekm@maven.pl> Cc: Frank Gevaerts <frank@gevaerts.be> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jean Delvare 提交于
The F71805F I/O resource structure needs not be a global variable, as the platform core allocs its own copy of it anyway. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Hartmut Rick 提交于
New driver (smsc47m192) which supports voltage and temperature measurement features of SMSC LPC47M192 and LPC47M997 chips. Signed-off-by: NHartmut Rick <linux@rick.claranet.de> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jean Delvare 提交于
Add alarms support for the W83627EHF/EHG hardware monitoring chip. This is based on an earlier patch from Rudolf Marek. Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Rudolf Marek 提交于
Add the voltage measuring support to W83627EHF. The code is based on the patch provided by Yuan Mu from Winbond. Signed-off-by: NYuan Mu <Ymu@winbond.com.tw> Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jordan Crouse 提交于
Add LM82 temperature sensor support (similar to the LM83, but less featureful). Signed-off-by: NJordan Crouse <jordan.crouse@amd.com> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 15 4月, 2006 1 次提交
-
-
由 Jean Delvare 提交于
Make the w83792d driver keep quiet when misdetecting a chip. This can happen, and the user doesn't need to know. Also renumber the messages, and add one, for consistency. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 11 4月, 2006 3 次提交
-
-
由 Andrew Morton 提交于
Use ENODEV when the hdaps hardware isn't there, not ENXIO. Cc: Jean Delvare <khali@linux-fr.org> Cc: Robert Love <rml@novell.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Robert Love 提交于
Add support for forthcoming Lenovo-branded machines to the HDAPS driver. Signed-off-by: NRobert Love <rml@novell.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: Dmitry Torokhov <dtor_core@ameritech.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Frank Gevaerts 提交于
This adds support for my Thinkpad R52, which for some reason is not matched by the "ThinkPad R52" line. Signed-off-by: NFrank Gevaerts <frank@gevaerts.be> Cc: Robert Love <rml@novell.com> Cc: Dmitry Torokhov <dtor_core@ameritech.net> Cc: Greg KH <greg@kroah.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 03 4月, 2006 1 次提交
-
-
由 Arjan van de Ven 提交于
This reverts the mutex conversion that was recently done to the hdaps driver; this coversion was buggy because the hdaps driver started using this semaphore in IRQ context, which mutexes do not allow. Easiest solution for now is to just revert the patch (the patch was part of a bigger GIT commit, 9a61bf63 but this only reverts this one file) Signed-off-by: NArjan van de Ven <arjan@linux.intel.com> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 24 3月, 2006 13 次提交
-
-
由 Alexey Dobriyan 提交于
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Mark M. Hoffman 提交于
Add required locking around idr_ routines, retry the idr_pre_get/idr_get_new pair properly, and sprinkle in some likely/unlikely for good measure. (Lack of idr locking didn't hurt when all callers were I2C clients, as the i2c-core serialized for us anyway. Now that we have non I2C hwmon drivers, this is truly necessary.) Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Darren Jenkins 提交于
"register" is a reserved keyword so using it as a parameter name can confuse some compilers, most notably ICC. The patch below just renames all occurences to reg which fits the actual function declarations. Signed-off-by: NDarren Jenkins <darrenrjenkins@gmail.com> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jean Delvare 提交于
Stop resetting the chip on load by default, so as to preserve the BIOS initializations. Same was done in the w83627hf driver some times ago for the same reasons. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Yuan Mu 提交于
Use dynamic sysfs callbacks and array of attributes to reduce the w83627ehf driver size. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jean Delvare 提交于
Add support for the Intel Pentium M series to the hwmon-vid driver. Signed-off-by: NJean Delvare <khali@linux-fr.org> Cc: Rudolf Marek <r.marek@sh.cvut.cz> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jean Delvare 提交于
Add support for the Winbond W83687THF chip to the w83627hf hardware monitoring driver. This new chip is almost similar to the already supported W83627THF chip, except for VID and a few other minor changes. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jean Delvare 提交于
Convert the new f71805f hardware monitoring driver to use mutexes instead of semaphores. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Ingo Molnar 提交于
convert drivers/hwmon/*.c semaphore use to mutexes. the conversion was generated via scripts, and the result was validated automatically via a script as well. all affected hwmon drivers were build-tested. Signed-off-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jean Delvare 提交于
Drop 3 useless macros in the w83792d hardware monitoring driver. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Yuan Mu 提交于
Use arrays of attributes in the w83792d driver. Signed-off-by: NJim Cromie <jim.cromie@gmail.com> Signed-off-by: NYuan Mu <ymu@winbond.com.tw> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jean Delvare 提交于
Convert the f71805f driver to use arrays of attributes. This shrinks the compiled module from 12.0 kB to 9.6 kB. We certainly should do the same for as many hardware monitoring drivers as possible. This, together with a nice chip design by Fintek, makes this driver very small, both in terms of number of lines of code and memory consumption. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jim Cromie 提交于
Convert individual sensors to sensor-attr arrays by each sensor type, and initialize them in loops instead of long blocks of individual calls. Signed-off-by: NJim Cromie <jim.cromie@gmail.com> Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-