Another remnant of the previous key locking scheme
needs to be removed -- this causes a warning
otherwise as ieee80211_set_default_mgmt_key will
acquire a mutex.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The intent was to free "msp->ratelist" here.  "msp->sample_table" is
always NULL at this point.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"It's not problematic if minstrel gets feedback for rates that it
doesn't have in its list, it should just ignore it. - Felix"
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Cc: Felix Fietkau <nbd@openwrt.org>

If sta is NULL, we will have problems long before we get here...
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Cc: Felix Fietkau <nbd@openwrt.org>

IBSS has never had locking, instead relying on some
memory barriers etc. That's hard to get right, and
I think we had it wrong too until the previous patch.
Since this is not performance sensitive, it doesn't
make sense to have the maintenance overhead of that,
so add proper locking.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bob reported a lockdep complaint originating in
the mac80211 IBSS code due to the common work
struct patch. The reason is that the IBSS and
station mode code have different locking orders
for the cfg80211 wdev lock and the work struct
(where "locking" implies running/canceling).

Fix this by simply not canceling the work in
the IBSS code, it is not necessary since when
the REQ_RUN bit is cleared, the work will run
without effect if it runs. When the interface
is set down, it is flushed anyway, so there's
no concern about it running after memory has
been invalidated either.

This fixes
https://bugzilla.kernel.org/show_bug.cgi?id=16419

Additionally, looking into this I noticed that
there's a small window while the IBSS is torn
down in which the work may be rescheduled and
the REQ_RUN bit be set again after leave() has
cleared it when a scan finishes at exactly the
same time. Avoid that by setting the ssid_len
to zero before clearing REQ_RUN which signals
to the scan finish code that this interface is
not active.
Reported-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When WEP is not available, we should reject shared
key authentication because it could never succeed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a station interface is reused as monitor interface it is possible that
the carrier is still set to off. This breaks packet injection on that
monitor interface.
Force the carrier on in monitor interface initialisation like it is also done
for other interface types (e.g. adhoc, mesh point, ap).
Signed-off-by: NDavid Gnedt <david.gnedt@davizone.at>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ever since

commit e1b3ec1a
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date:   Mon Mar 29 12:18:34 2010 +0200

    mac80211: explicitly disable/enable QoS

mac80211 is telling drivers, in particular
iwlwifi, whether QoS is enabled or not.

However, this is only relevant for station mode,
since only then will any device send nullfunc
frames and need to know whether they should be
QoS frames or not. In other modes, there are
(currently) no frames the device is supposed to
send.

When you now consider virtual interfaces, it
becomes apparent that the current mechanism is
inadequate since it enables/disables QoS on a
global scale, where for nullfunc frames it has
to be on a per-interface scale.

Due to the above considerations, we can change
the way mac80211 advertises the QoS state to
drivers to only ever advertise it as "off" in
station mode, and make it a per-BSS setting.
Tested-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When aggregation related action frames are enqueued for further work,
and they originate from a STA that is part of an AP VLAN, they are
currently enqueued for the AP interface. This breaks the sta_info_get()
lookup in the actual work function, and because of that, aggregation
sessions are not established for this STA.

Fix this by replacing the sta_info_get call with a call to
sta_info_get_bss.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do this by poisoning the values of wep_tx_tfm and wep_rx_tfm if either
crypto allocation fails.
Reported-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch will also fix the odd freeze which occurred
when minstrel_ht connects to an 802.11n network with
legacy hardware.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current mac80211 code assumes that WEP is always available.  If WEP
fails to initialize, ieee80211_register_hw will always fail.

In some cases (e.g. FIPS certification), the cryptography used by WEP is
unavailable.  However, in such cases there is no good reason why CCMP
encryption (or even no link level encryption) cannot be used.  So, this
patch removes mac80211's assumption that WEP (and TKIP) will always be
available for use.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The check should be against current top2 rate, instead of
current top rate.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The throughput should be considered when updating rate
with best probability.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow selection of minstrel_ht as default rate control algorithm. At
the moment minstrel_ht can only be requested by the driver code but
not selected as default in make menuconfig. Fix this by using
minstrel_ht when minstrel was selected as default and minstrel_ht
is available.

This change won't affect legacy devices as minstrel_ht falls back to
minstrel in that case.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This check is duplicated in drv_get_survey.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Because of an ambiguity in the for_each_sta_info macro, it can
currently only be used if the third parameter is set to 'sta'.
Fix this by renaming the parameter to '_sta'.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This avoids the extra queueing from calling netif_rx.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This avoids the extra queueing from calling netif_rx.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In preparation for a TX power setting interface in the nl80211, change the
.set_tx_power function to use mBm units instead of dBm for greater accuracy and
smaller power levels.

Also, already in advance move the tx_power_setting enumeration to nl80211.

This change affects the .tx_set_power function prototype. As a result, the
corresponding changes are needed to modules using it. These are mac80211,
iwmc3200wifi and rndis_wlan.

Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Acked-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While mesh_rx_plink_frame holds sta->lock...

mesh_rx_plink_frame ->
	mesh_plink_inc_estab_count ->
		ieee80211_bss_info_change_notify

...but ieee80211_bss_info_change_notify is allowed to sleep.  A driver
taking advantage of that allowance can cause a scheduling while
atomic bug.  Similar paths exist for mesh_plink_dec_estab_count,
so work around those as well.

http://bugzilla.kernel.org/show_bug.cgi?id=16099

Also, correct a minor kerneldoc comment error (mismatched function names).
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>

net/mac80211/rc80211_minstrel_ht.c:440:46: warning: incorrect type in argument 2 (different signedness)
net/mac80211/rc80211_minstrel_ht.c:440:46:    expected int *idx
net/mac80211/rc80211_minstrel_ht.c:440:46:    got unsigned int *<noident>
net/mac80211/rc80211_minstrel_ht.c:446:46: warning: incorrect type in argument 2 (different signedness)
net/mac80211/rc80211_minstrel_ht.c:446:46:    expected int *idx
net/mac80211/rc80211_minstrel_ht.c:446:46:    got unsigned int *<noident>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>

net/mac80211/rx.c:2059:39: warning: symbol 'mgmt' shadows an earlier one
net/mac80211/rx.c:1916:31: originally declared here
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This mechanism introduced in this patch applies (at least) for hardware
designs using a single shared antenna for both WLAN and BT. In these designs,
the antenna must be toggled between WLAN and BT.

In those hardware, managing WLAN co-existence with Bluetooth requires WLAN
full power save whenever there is Bluetooth activity in order for WLAN to be
able to periodically relinquish the antenna to be used for BT. This is because
BT can only access the shared antenna when WLAN is idle or asleep.

Some hardware, for instance the wl1271, are able to indicate to the host
whenever there is BT traffic. In essence, the hardware will send an indication
to the host whenever there is, for example, SCO traffic or A2DP traffic, and
will send another indication when the traffic is over.

The hardware gets information of Bluetooth traffic via hardware co-existence
control lines - these lines are used to negotiate the shared antenna
ownership. The hardware will give the antenna to BT whenever WLAN is sleeping.

This patch adds the interface to mac80211 to facilitate temporarily disabling
of dynamic power save as per request of the WLAN driver. This interface will
immediately force WLAN to full powersave, hence allowing BT coexistence as
described above.

In these kind of shared antenna desings, when WLAN powersave is fully disabled,
Bluetooth will not work simultaneously with WLAN at all. This patch does not
address that problem. This interface will not change PSM state, so if PSM is
disabled it will remain so. Solving this problem requires knowledge about BT
state, and is best done in user-space.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the following compile warning:

CC [M]  net/mac80211/scan.o
net/mac80211/scan.c: In function 'ieee80211_request_internal_scan':
net/mac80211/scan.c:749:23: warning: comparison between 'enum nl80211_band' and 'enum ieee80211_band'

caused by the local variable band not being of the proper 'ieee80211_band' type.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, detection in hwsim and ath9k can
detect that two sw scans are in flight at the
same time, which isn't really true. It is
caused by a race condition, because the scan
complete callback is called too late, after
the lock has been dropped, so that a new scan
can be started before it is called.

It is also called too early semantically, as
it is currently called _after_ the return to
the operating channel -- it should be before
so that drivers know this is the operating
channel again.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

regression introduced by b8d92c9c

In function ‘ieee80211_work_rx_queued_mgmt’:
warning: ‘rma’ may be used uninitialized in this function

this re-adds default value WORK_ACT_NONE back to rma
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When management frame protection (IEEE 802.11w) is used, we must use a
separate counter for tracking received CCMP packet number for the
management frames. The previously used NUM_RX_DATA_QUEUESth queue was
shared with data frames when QoS was not used and that can cause
problems in detecting replays incorrectly for robust management frames.
Add a new counter just for robust management frames to avoid this issue.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When management frame protection (IEEE 802.11w) is used,
Deauthentication frame needs to be protected when the pairwise key is
configured. mac80211 was removing the station entry (and its keys)
before actually sending out the Deauthentication frame. Fix this by
reordering the code to send the frame before the station entry gets
removed. This matches an earlier change that handled the Disassociation
frame processing, but missed Deauthentication frames.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ps-qos latency handling is broken. It uses predetermined latency values
to select specific dynamic PS timeouts. With common AP configurations, these
values overlap with beacon interval and are therefore essentially useless
(for network latencies less than the beacon interval, PSM is disabled.)

This patch remedies the problem by replacing the predetermined network latency
values with one high value (1900ms) which is used to go trigger full psm. For
backwards compatibility, the value 2000ms is still mapped to a dynamic ps
timeout of 100ms.

Currently also the mac80211 internal value for storing user space configured
dynamic PSM values is incorrectly in the driver visible ieee80211_conf struct.
Move it to the ieee80211_local struct.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a circular locking dependency when configuring the
hardware ARP filters on association, occurring when flushing the mac80211
workqueue. This is what happens:

[   92.026800] =======================================================
[   92.030507] [ INFO: possible circular locking dependency detected ]
[   92.030507] 2.6.34-04781-g2b2c009e #85
[   92.030507] -------------------------------------------------------
[   92.030507] modprobe/5225 is trying to acquire lock:
[   92.030507]  ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8105b5c0>] flush_workq
ueue+0x0/0xb0
[   92.030507]
[   92.030507] but task is already holding lock:
[   92.030507]  (rtnl_mutex){+.+.+.}, at: [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[   92.030507]
[   92.030507] which lock already depends on the new lock.
[   92.030507]
[   92.030507]
[   92.030507] the existing dependency chain (in reverse order) is:
[   92.030507]
[   92.030507] -> #2 (rtnl_mutex){+.+.+.}:
[   92.030507]        [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[   92.030507]        [<ffffffff81341754>] mutex_lock_nested+0x44/0x300
[   92.030507]        [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[   92.030507]        [<ffffffffa022d47c>] ieee80211_assoc_done+0x6c/0xe0 [mac80211]
[   92.030507]        [<ffffffffa022f2ad>] ieee80211_work_work+0x31d/0x1280 [mac80211]

[   92.030507] -> #1 ((&local->work_work)){+.+.+.}:
[   92.030507]        [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[   92.030507]        [<ffffffff8105a51a>] worker_thread+0x22a/0x370
[   92.030507]        [<ffffffff8105ecc6>] kthread+0x96/0xb0
[   92.030507]        [<ffffffff81003a94>] kernel_thread_helper+0x4/0x10
[   92.030507]
[   92.030507] -> #0 ((wiphy_name(local->hw.wiphy))){+.+.+.}:
[   92.030507]        [<ffffffff81075fdc>] __lock_acquire+0x1c0c/0x1d50
[   92.030507]        [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[   92.030507]        [<ffffffff8105b60e>] flush_workqueue+0x4e/0xb0
[   92.030507]        [<ffffffffa023ff7b>] ieee80211_stop_device+0x2b/0xb0 [mac80211]
[   92.030507]        [<ffffffffa0231635>] ieee80211_stop+0x3e5/0x680 [mac80211]

The locking in this case is quite complex. Fix the problem by rewriting the
way the hardware ARP filter list is handled - i.e. make a copy of the address
list to the bss_conf struct, and provide that list to the hardware driver
when needed.

The current patch will enable filtering also in promiscuous mode. This may need
to be changed in the future.
Reported-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove BSS from cfg80211 BSS list if we are only member in IBSS when
leaving it.
Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add changed basic rates flag to bss_changed while joinig ibss network.

This patch is split from the patch containing support for setting basic
rates when creating ibss network. Original patch was posted by Johannes
Berg on the linux-wireless posting list.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support to nl80211 and mac80211 to set basic rates when
joining/creating ibss network.

Original patch was posted by Johannes Berg on the linux-wireless posting list.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, driver tracing is sometimes invoked
after and sometimes before the actual driver
callback. This is fine as long as the driver
has no tracing itself, but as soon as it does
it gets confusing.

To make traces containing such information
easier to read, introduce a return tracer in
mac80211 that essentially brackets any driver
tracing, and invoke the real trace before the
driver's callback, only showing the return
value, if any, afterwards.

Since tracing records the process, there's no
problem with overlapping calls if that should
happen.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The recent change to processing action frames from
the management frame queue had already broken action
frame accounting, and my rework didn't help either.
So add back accounting and simplify the code with a
label rather than duplicating it, and also add
accounting for management frames.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Even before the recent changes, the documentation
for TX aggregation was somewhat out of date. Update
it and also add documentation for the RX side.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>