This patch adds "#ifndef __<header>_H" for protecting header from double
inclusion.
Signed-off-by: NRayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the name of the macro used to mask the
mmc interrupt: erroneously it was used: MMC_DEFAUL_MASK.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Erroneously the DWMAC_CORE_3_40 was set to 34 instead of 0x34.
This can generate problems when run on old chips because
the driver assumes that there are the extra 16 regs available
for perfect filtering.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When getting clock, give a chance to the CPUs without DT support,
which use Common Clock Framework, such as Loongson1B.
Signed-off-by: NKelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

 - Use kcalloc() / vzalloc() instead of an extra bitmap_zero().
 - Add __GFP_NOWARN to kcalloc() since we'll try vzalloc() if it fails.
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix some issues around int variables used in data structures related
to memory registration.

Handle int overflow in mlx4_init_icm_table by using a u64 intermediate
variable and changing struct mlx4_icm_table num_obj field to be u32.

Change some more fields/variables to use u32 instead of int to prevent
a case where the variable becomes negative when bit 31 is set.

Also subtract log_mtts_per_seg from the exponent when computing
num_mtt, since its added later on in that very same code area.

This and the previous commit fixes some issues which actually prevent
commit db5a7a65 ("mlx4_core: Scale size of MTT table with system
RAM") from working.  Now, when the number of MTTs is scaled with the
size of the RAM we can map up to 8TB.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

mlx4_buddy_init uses kmalloc() to allocate bitmaps, which fails when
the required size is beyond the max supported value (or when memory is
too fragmented to handle a huge allocation).  Extend this to use use
vmalloc() if kmalloc() fails, and take that into account when freeing
the bitmaps as well.

This fixes a driver load failure when log num mtt is 26 or higher, and
is a step in the direction of allowing to register huge amounts of
memory on large memory systems.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Convert a 0 error return code to a negative one, as returned elsewhere in the
function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@

(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
    when != ret = e3
*if (x == NULL || ...)
{
  ... when != ret = e4
*  return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a 0 error return code to a negative one, as returned elsewhere in the
function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@

(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
    when != ret = e3
*if (x == NULL || ...)
{
  ... when != ret = e4
*  return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.

The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@

- T i = E->fld;
+ T i;
  ... when != E
      when != i
  if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following compiler warnings:

 - drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:2908:3: warning: comparison
   of distinct pointer types lacks a cast [enabled by default]
 - drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c:1709:7: warning: comparison
   of distinct pointer types lacks a cast [enabled by default]
Signed-off-by: NJoren Van Onder <joren.vanonder@gmail.com>
Acked-By: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds missing braces around the 10gig link check to include the check for  KR support.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Reported-by: NSascha Wildner <saw@online.de>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During probe, every function probed clears the recovery registers from
all functions on its path - thus signaling that given a future recovery
event, there will be no need to wait for those functions.

This is a flawed behaviour - each function should only be responsible
for its own bit.

Since this registers are handled during the load/unload routines,
this cleanup is removed altogether.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing previous driver unload flow is flawed, causing the probe of
functions reaching the 'uncommon fork' in flr-capable devices to fail.

This patch resolves this, as well as fixing the flow for hypervisors which
disable flr capabilities from functions as they pass them as PDA to VMs,
as we cannot base the flow on the pci configuration space.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It looks like the register defines for DCA were never updated after going from
82575 to 82576.  This change addresses that by updating the defines.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().

This patch avoids phys_to_virt() by using skb->data and the address of the
pages allocated for Rx.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().

This patch avoids phys_to_virt() by making using skb->data and the address
of the pages allocated for Rx.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

Driver probe functions are generally __devinit so they will be
discarded after initialization for non-hotplug kernels.
This was found by a new warning after patch 6a228452 "stmmac: Add
device-tree support" adds a new __devinit function that is called
from stmmac_pltfr_probe.

Without this patch, building socfpga_defconfig results in:

WARNING: drivers/net/ethernet/stmicro/stmmac/stmmac.o(.text+0x5d4c): Section mismatch in reference from the function stmmac_pltfr_probe() to the function .devinit.text:stmmac_probe_config_dt()
The function stmmac_pltfr_probe() references
the function __devinit stmmac_probe_config_dt().
This is often because stmmac_pltfr_probe lacks a __devinit
annotation or the annotation of stmmac_probe_config_dt is wrong.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: NStefan Roese <sr@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The #ifdefs regarding CONFIG_ARCH_LPC32XX_MII_SUPPORT and
CONFIG_ARCH_LPC32XX_IRAM_FOR_NET are obsolete since the symbols have been
removed from Kconfig and replaced by devicetree based configuration.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some 8086:10c9 NICs have a problem completing the ethtool loopback test.
The result looks like this:

ethtool -t eth1
The test result is FAIL
The test extra info:
Register test  (offline)         0
Eeprom test    (offline)         0
Interrupt test (offline)         0
Loopback test  (offline)         13
Link test   (on/offline)         0

A bisect clearly points to commit a95a0744.
However that seems to only trigger the bug. While adding some printk the
problem disappeared, so this might be a timing issue. After some trial and
error I discovered that adding a small delay just before igb_write_phy_reg()
in igb_integrated_phy_loopback() allows the loopback test to succeed.
I was unable to figure out the root cause so far but I expect it to be
somewhere in the following executing path
igb_integrated_phy_loopback
->igb_write_phy_reg_igp
  ->igb_write_phy_reg_mdic
    ->igb_acquire_phy_82575
      ->igb_acquire_swfw_sync_82575

The problem could only be observed on 8086:10c9 NICs so far and not all
of them show the behaviour. I did not restrict the workaround to this
type of NIC as it should do no harm to other igb NICs.

With the patch below the loopback test succeeded 500 times in a row
using a NIC that would otherwise fail.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

A bus trace shows that while executing e1000e_down, TCTL is cleared except
for the PSP bit.  This occurs while in the middle of fetching a TSO packet
since the Tx packet buffer is full at that point. Before the device is
reset, the e1000_watchdog_task starts to run from the middle (it was
apparently pre-empted earlier, although that is not in the trace) and sets
TCTL.EN.  At that point, 82571 transmits the corrupted packet, apparently
because TCTL.MULR was cleared in the middle of fetching a packet, which is
forbidden.

Driver should just clear TCTL.EN in e1000_reset_hw_82571 instead of
clearing the entire register, so as not to change any settings in the
middle of fetching a packet.
Signed-off-by: NTushar Dave <tushar.n.dave@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

Found that commit d478eb44 was a bad commit.
If the link partner is transmitting codeword (even if NULL codeword),
then the RXCW.C bit will be set so check for RXCW.CW is unnecessary.
Ref: RH BZ 840642
Reported-by: NFabio Futigami <ffutigam@redhat.com>
Signed-off-by: NTushar Dave <tushar.n.dave@intel.com>
CC: Marcelo Ricardo Leitner <mleitner@redhat.com>
CC: stable <stable@vger.kernel.org> [2.6.38+]
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

When building with ixp4xx_eth and ptp_ixp46x as module, one is getting the
following error:

ERROR: "ixp46x_phc_index" [drivers/ptp/ptp_ixp46x.ko] undefined!

This has been introduced by commit 509a7c25.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even when they go beyond 80 characters, user visible strings should be
on one line to make them easy to grep for.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

In the original code
...
 	if ((adapter->hw.mac.type == e1000_i210)
		|| (adapter->hw.mac.type == e1000_i210)) {
...
the second check of 'adapter->hw.mac.type' is pointless since it tests
for the exact same value as the first.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

Move nvm invalid size check to before size assigned by mac_type for
82575 and later parts in get_invariants function.  This fixes a problem
found on some 82576 devices where the part will not initialize because
the nvm_read function pointer ends up getting assigned to the incorrect
function.

Reported By: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

Port1=Eth, Port2=IB restriction is no longer required.
Having RoCE, there will always rdma port initialized over ConnectX
physical port, no matter whether the link layer is IB or Ethernet.
So we always have dual port IB device.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing the ring->blocked flag, it is redundant and leads to a race:

We close the TX queue and then set the "blocked" flag.
Between those 2 operations the completion function can check the "blocked"
flag, sees that it is 0, and wouldn't open the TX queue.

Using netif_tx_queue_stopped to check the state of the queue to avoid this race.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Should NOT check SMAC=DMAC when:
1. loopback is turned on
2. validate_loopback is true.

Fixed it accordingly.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Missing a CR in printk causes 2 messages printed in one line.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnx2x_mcast_enqueue_cmd() we'll leak the memory allocated to
'new_cmd' if we hit the deafault case of the 'switch (cmd)'.
Add a 'kfree(new_cmd)' to that case to avoid the leak.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently an skb requiring TSO may not fit within a minimum-size TX
queue.  The TX queue selected for the skb may stall and trigger the TX
watchdog repeatedly (since the problem skb will be retried after the
TX reset).  This issue is designated as CVE-2012-3412.

Set the maximum number of TSO segments for our devices to 100.  This
should make no difference to behaviour unless the actual MSS is less
than about 700.  Increase the minimum TX queue size accordingly to
allow for 2 worst-case skbs, so that there will definitely be space
to add an skb after we wake a queue.

To avoid invalidating existing configurations, change
efx_ethtool_set_ringparam() to fix up values that are too small rather
than returning -EINVAL.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The skb->pfmemalloc flag gets set to true iff during the slab allocation
of data in __alloc_skb that the the PFMEMALLOC reserves were used.  If
page splitting is used, it is possible that pages will be allocated from
the PFMEMALLOC reserve without propagating this information to the skb.
This patch propagates page->pfmemalloc from pages allocated for fragments
to the skb.

It works by reintroducing and expanding the skb_alloc_page() API to take
an skb.  If the page was allocated from pfmemalloc reserves, it is
automatically copied.  If the driver allocates the page before the skb, it
should call skb_propagate_pfmemalloc() after the skb is allocated to
ensure the flag is copied properly.

Failure to do so is not critical.  The resulting driver may perform slower
if it is used for swap-over-NBD or swap-over-NFS but it should not result
in failure.

[davem@davemloft.net: API rename and consistency]
Signed-off-by: NMel Gorman <mgorman@suse.de>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in
clk.h, there is no need to have clk code enclosed in #ifdef
CONFIG_HAVE_CLK, #endif macros.

This also fixes error paths of probe(), as a goto is required in this
patch.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Spinlock should be taken before checking for tp->hw_stats.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After Power-on-reset, the 5719's TX DMA length registers may contain
uninitialized values and cause TX DMA to stall.  Check for invalid
values and set a register bit to flush the TX channels.  The bit
needs to be turned off after the DMA channels have been flushed.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The workaround was mis-applied to all 5719 and 5720 chips.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

to prevent PHY access conflict with APE firmware.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>