Fix dev->stop shutdown bug where driver was stopping xmit queue and then
disabling intrs.  Fix is to disable intrs first and then stop the xmit
queue, otherwise an interrupt could cause the queue to be rewoken.  Also,
no need to explicitly do queue servicing because queues are cleaned and
reset back to initial state at end of dev->stop.  Servicing queues also
had the side-effect of also rewakening the xmit queue, which is not what
we want.
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provision for multiple Rx/Tx queues.  Max of 8 WQs and 8 RQs.  Max for
completion queue is 8+8=16 and max for interrupt resources is 8+8+2.

Add driver/firmware interface for setting up RSS secret key and indirection
table.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug fix: included MAC drops in rx_dropped netstat.  Also track Rx trunctations
stat at the MAC
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nic firmware can place resources (queues, intrs, etc) on multiple BARs, so
allow driver to discover/map resources beyond BAR0.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report all bad FCS errs as frames errs.  This includes frames with bad
FCS on wire detected by MAC and frames which may be truncated due to
ingress FIFO overruns.  No longer print a driver msg on bad FCS err.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return notify intr credits after notify intr from firmware.  This is
especially important for legacy PCI intr mode, where not returning
credits would cause PBA to remain asserted which would get us right
back into the ISR.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable ethtool support for get/set_flags so LRO can be turned on/off
by fwding drivers such as the bridge driver.  LRO is not compatible
with fwding drivers.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug fix: don't set netdev->name early before netdev registration.  Setting
netdev->name early with dev_alloc_name() would occasionally cause netdev
registration to fail returning error that device was already registered.
Since we're using netdev->name to name MSI-X vectors, we now need to
move the request_irq after netdev registartion, so move it to ->open.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fixes for review items from Ben Hutchings:
 - use netdev->net_stats rather than private net_stats
 - use ethtool op .get_sset_count rather than .get_stats_count
 - err out if setting Tx/Rx csum or TSO using ethtool and setting is
   not enabled for device.
 - pass in jiffies + constant to round_jiffies
 - return err if new MTU is out-of-bounds
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>