FCoE license info must be initialized at probe(), but
iSCSI at open().
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FW includes the following fixes:
  1. (iSCSI) Arrival of un-solicited ASYNC message causes
     firmware to abort the connection with RST.
  2. (FCoE) There is a probability that truncated FCoE packet on
     RX path won't get detected which might lead to FW assert.
  3. (iSCSI) Arrival of target-initiated NOP-IN during intense
     ISCSI traffic might lead to FW assert.
  4. (iSCSI) Chip hangs when in case of retransmission not aligned
     to 4-bytes from the beginning of iSCSI PDU.
  5. (FCoE) Arrival of packets beyond task IO size can lead to crash.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a problem in which the host stops receiving data after
restarting the interface. This issue is caused by combination of incorrect
data path tap closure, along with missing MAC reset.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fix solves a problem of no link on 578xx-KR by retrying to link up to
four timer using the periodic function.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust blink rate on 578xx to fit its clock rate.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x allocates a full page per fragment.

We must account in skb->truesize, the size of the fragment, not the used
part of it.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.

Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This code is after the break statement so it never gets used.  The
"vlan_mac_obj" variable does get initialized properly, so we can just
delete this.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct the description of ethtool_rxnfc::rule_locs; it is an array
of currently used locations, not all possible valid locations.

Add note that drivers must not use ethtool_rxnfc::rule_locs.

The rule_locs argument to ethtool_ops::get_rxnfc is either NULL or a
pointer to an array of u32, so change the parameter type accordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Mon, 2011-08-29 at 13:28 -0700, Randy Dunlap wrote:
> (on i386 or x86_64)
>
> drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:10148: error: 'bnx2x_fcoe_get_wwn' undeclared here (not in a function)

This should sync #define structures between definition and declaration
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BCM54616 PHY is very similar to the 54618SE, only without EEE support, which will not be activated due to querying the actual PHY type.
This check is already done by reading a dedicated PHY register.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x used to be able to set rxhash, but this was lost in the conversion
to hw_features (commit 66371c44).
Restore it and enable it by default.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
CC: Vladislav Zolotarov <vladz@broadcom.com>
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Dmitry Kravkov <dmitry@broadcom.com>
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are valid configurations where Max BW is configured to zero for
some VNs.
Print the message only if debugging is enabled and do not call the
configuration "illegal".

[v2: use DP(), not BNX2X_DBG_ERR(); recommended by Eilon Greenstein.]
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use IFF_UNICAST_FTL to find out if driver handles unicast address
filtering. In case it does not, promisc mode is entered.

Patch also fixes following drivers:
stmmac, niu: support uc filtering and yet it propagated
	ndo_set_multicast_list
bna, benet, pxa168_eth, ks8851, ks8851_mll, ksz884x : has set
	ndo_set_rx_mode but do not support uc filtering
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add pr_fmt(fmt) KBUILD_MODNAME ": " to prefix messages with "bnx2x: ".
Remove #define DP_LEVEL and use pr_notice.
Repeating KERN_<LEVEL> isn't necessary in multi-line printks.
printk macro neatening, use fmt and ##__VA_ARGS__.
Coalesce long formats.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Uses of pr_cont should be avoided where reasonably possible
because they can be interleaved by other threads and processes.

Coalesce pr_cont uses.

Fix typos, duplicated words and spacing in DP uses caused
by split multi-line formats.  Coalesce some of these
split formats.  Add missing terminating newlines to DP uses.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use %pM and mac address directly instead.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the drivers for Broadcom devices into
drivers/net/ethernet/broadcom/ and the necessary Kconfig and Makefile
changes.

CC: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Gary Zambrano <zambrano@broadcom.com>
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>