Try to detect that the AP is not using aggregation even when there's
enough traffic to make it worthwhile; if this is the case and U-APSD
is enabled then assume the AP is broken (like so many) and doesn't
enable aggregation when U-APSD is used. In this case, disconnect from
the AP and blacklist U-APSD for a potential new connection to it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Traffic condition monitor gathers data about the traffic load and
other conditions and can be used to make decisions regarding latency,
throughput etc.  This patch introduces the code and data structures to
collect this data for future use.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Update the scan command API with support for adaptive dwell.  Adaptive
dwell is a type of scan that dynamically changes the time it remains
on each channel listening for beacons or probe responses.
Signed-off-by: NRoee Zamir <roee.zamir@intel.com>
Signed-off-by: NBeni Lev <beni.lev@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Tx BA session should be started according to the current throughput
without any dependence on the internal rate scaling state. The criteria
for opening a BA session will be 10 frames per second.

Sending frequent del BAs can cause inter-op issues with some APs. We'll
not close a BA session until we receive an explicit del BA from the
peer.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The corunning block was supposed to help in coex scenarios.
It required the driver to configure the firmware based on
the coupling between the two antennas of the devices.
This was never in use and the configuration sent by the
driver has always been blank.
Remove all that code.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For testing purposes, we may want to disable EBS scans at compile time.
Signed-off-by: NRoee Zamir <roee.zamir@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add configuration for allowing driver's nvm parsing and
bypassing the new host command, for debugging.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add a constant to allow disabling checksum. This will enable easier
debugging in early phases.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This allows to disable uapsd for BSS only, or P2P client
separately. Remove the now unneeded
IWL_MVM_P2P_UAPSD_STANDALONE constant.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Slow platforms may have issues with dumping data upon
firmware assert. Make it easier to disable it for those
platform.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enable snoozing and U-APSD on P2P client. The firwmare will
support this only if the BSS vif is not associated.
Make this configurable by a constant variable and disable
it by default.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow to configure the driver to pretend to have TX CSUM
offload support. This will be useful to test the TSO flows
that will come in further patches.
This configuration is disabled by default.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Those timeouts are used for AM-to-PSM transition.
We already have those pairs defined for default and WOWLAN use cases.
We expect that by using shorter threshold for low latency P2P,
e.g. for Miracast video scenario, we might save a considerable amount of power.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove an old workaround that's no longer needed and
enable MIMO on P2P interfaces.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is a tweak which has been shown to improve performance when
moving away from the AP while working in 80Mhz.
When RS decides to go down to 80MHz SISO MCS0 instead switch to 20MHz MCS4.
Go back to 80MHz MCS1 if RS can sustain 20MHz MCS5.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

ToF is a time based method for measurement of the WiFi device
location within a WiFi environment. The driver functionality provided
by this patch is the interface for communication with FW and receiving
location related updates from the FW. The interface provided by this
patch is via debugfs.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The quota threshold should be reduced to 4 to update the
firmware more frequently.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allow to better preserve the BT performance while
WiFi is running.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is to work around interoperability bugs with devices
that don't hanle MIMO properly.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Repeating the legacy rates avoids degrading quickly to
lower rates due to collisions which is common when doing
TCP Tx traffic in legacy.
This slightly improves TCP Tx throughput while working
in legacy in different scenarios.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Organize and cleanup the consts used by rs.
This is part of making some of these configurable.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This impacts the partition between BT and Wifi.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The TTC and RRC features are supported by the newer
firmwares. It allows to reach better overall WiFi and BT
performance. When the RRC is enabled, we don't need to force
the AP to send SISO frames, but it can keeps sending MIMO
frames.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This makes it easier to tune the values during the testing.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The MVM_FW_BCAST_FILTER_PASS_ALL option defined in iwl-dbg-cfg.ini
configuration file allows to enable/disable FW broadcast filtering.

If MVM_FW_BCAST_FILTER_PASS_ALL is not defined in iwl-dbg-cfg.ini or
its value is 0, the mvm broadcast filtering is enabled.

Setting MVM_FW_BCAST_FILTER_PASS_ALL=1 in iwl-dbg-cfg.ini blocks sending
of BCAST_FILTER_CMD to FW.
Signed-off-by: NMax Stepanov <Max.Stepanov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is were it really needs to be.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The current TLC isn't optimized for low latency and some devices
have issues with MIMO. This kind of combo creates latency issues.
Allow to temporarily disable MIMO for tests in order to solve
the latency issues without the added complexity of MIMO.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The tables still contain dummy values.

Cc: <stable@vger.kernel.org> [3.15+]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Improve the initial tx rate and antenna selection to be based on
the rssi of the last rx. This avoids starting at the lowest legacy
rate always and requiring more tx traffic to "climb" up the rates.
Since this option might cause trouble in certain setups, allow to
disable it by default.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When updating quota in the firmware, it has to reset quite a bit
of internal state, which apparently can have an adverse impact on
its operation.

Avoid that by only updating the quota command when there are any
signification changes, i.e. added/removed bindings or changes in
quota that are bigger than 8 TU within a binding.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add MVM_FW_MCAST_FILTER_PASS_ALL option to iwl-dbg-cfg.ini configuration file
to enable/disable FW multicast filtering.
Signed-off-by: NMax Stepanov <Max.Stepanov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.

For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This really belongs to the constants file.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware decided to not implement this API in this way,
so for now remove setting the field completely. This will
allow the firmware to change how to use this field later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to debug the firmware, we need to be able to set
the BT priority of WiFi packets. This priority is set based
on the type of the packet (control frames, EAPOL etc...).
For debugging purposes, allow to override this priority by
a debugfs controlled value.
Enable this feature that needs this priority to be able to
test it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

7265 features a new calibration which is called antenna
coupling. The purpose of this calibration (which isn't
really a calibration), is to measure the isolation between
the antennas and that can give us useful information for
the Coex modules.

With this information, we can tune the LookUpTables (LUTs)
that define the BT / WiFi contention policy.

The LUTs currently contain dummy values - but they will be
updated soon.

While at it, change the current code to stop duplicate the
host command while sending. This was needed back then, when
the command was short enough to be allocated on the stack.
Since then, the command grew a lot and is now allocated on
the heap - hence we can use the NOCOPY option instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>