Skip to content

K
kernel_linux

OpenHarmony / kernel_linux
上一次同步 3 年多

通知 13
Star 8
Fork 2
K
kernel_linux
切换分支/标签
  1. 23 4月, 2012 1 次提交
  3. 22 4月, 2012 7 次提交
    • N
      tcp: move duplicate code from tcp_v4_init_sock()/tcp_v6_init_sock() · 900f65d3
      由 Neal Cardwell 提交于 
      This commit moves the (substantial) common code shared between
tcp_v4_init_sock() and tcp_v6_init_sock() to a new address-family
independent function, tcp_init_sock().

Centralizing this functionality should help avoid drift issues,
e.g. where the IPv4 side is updated without a corresponding update to
IPv6. There was already some drift: IPv4 initialized snd_cwnd to
TCP_INIT_CWND, while the IPv6 side was still initializing snd_cwnd to
2 (in this case it should not matter, since snd_cwnd is also
initialized in tcp_init_metrics(), but the general risks and
maintenance overhead remain).

When diffing the old and new code, note that new tcp_init_sock()
function uses the order of steps from the tcp_v4_init_sock()
implementation (the order is slightly different in
tcp_v6_init_sock()).
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      900f65d3
    • P
      tcp: Repair connection-time negotiated parameters · b139ba4e
      由 Pavel Emelyanov 提交于 
      There are options, which are set up on a socket while performing
TCP handshake. Need to resurrect them on a socket while repairing.
A new sockoption accepts a buffer and parses it. The buffer should
be CODE:VALUE sequence of bytes, where CODE is standard option
code and VALUE is the respective value.

Only 4 options should be handled on repaired socket.

To read 3 out of 4 of these options the TCP_INFO sockoption can be
used. An ability to get the last one (the mss_clamp) was added by
the previous patch.

Now the restore. Three of these options -- timestamp_ok, mss_clamp
and snd_wscale -- are just restored on a coket.

The sack_ok flags has 2 issues. First, whether or not to do sacks
at all. This flag is just read and set back. No other sack  info is
saved or restored, since according to the standart and the code
dropping all sack-ed segments is OK, the sender will resubmit them
again, so after the repair we will probably experience a pause in
connection. Next, the fack bit. It's just set back on a socket if
the respective sysctl is set. No collected stats about packets flow
is preserved. As far as I see (plz, correct me if I'm wrong) the
fack-based congestion algorithm survives dropping all of the stats
and repairs itself eventually, probably losing the performance for
that period.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b139ba4e
    • P
      tcp: Report mss_clamp with TCP_MAXSEG option in repair mode · 5e6a3ce6
      由 Pavel Emelyanov 提交于 
      The mss_clamp is the only connection-time negotiated option which
cannot be obtained from the user space. Make the TCP_MAXSEG sockopt
report one in the repair mode.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5e6a3ce6
    • P
      tcp: Repair socket queues · c0e88ff0
      由 Pavel Emelyanov 提交于 
      Reading queues under repair mode is done with recvmsg call.
The queue-under-repair set by TCP_REPAIR_QUEUE option is used
to determine which queue should be read. Thus both send and
receive queue can be read with this.

Caller must pass the MSG_PEEK flag.

Writing to queues is done with sendmsg call and yet again --
the repair-queue option can be used to push data into the
receive queue.

When putting an skb into receive queue a zero tcp header is
appented to its head to address the tcp_hdr(skb)->syn and
the ->fin checks by the (after repair) tcp_recvmsg. These
flags flags are both set to zero and that's why.

The fin cannot be met in the queue while reading the source
socket, since the repair only works for closed/established
sockets and queueing fin packet always changes its state.

The syn in the queue denotes that the respective skb's seq
is "off-by-one" as compared to the actual payload lenght. Thus,
at the rcv queue refill we can just drop this flag and set the
skb's sequences to precice values.

When the repair mode is turned off, the write queue seqs are
updated so that the whole queue is considered to be 'already sent,
waiting for ACKs' (write_seq = snd_nxt <= snd_una). From the
protocol POV the send queue looks like it was sent, but the data
between the write_seq and snd_nxt is lost in the network.

This helps to avoid another sockoption for setting the snd_nxt
sequence. Leaving the whole queue in a 'not yet sent' state (as
it will be after sendmsg-s) will not allow to receive any acks
from the peer since the ack_seq will be after the snd_nxt. Thus
even the ack for the window probe will be dropped and the
connection will be 'locked' with the zero peer window.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c0e88ff0
    • P
      tcp: Initial repair mode · ee995283
      由 Pavel Emelyanov 提交于 
      This includes (according the the previous description):

* TCP_REPAIR sockoption

This one just puts the socket in/out of the repair mode.
Allowed for CAP_NET_ADMIN and for closed/establised sockets only.
When repair mode is turned off and the socket happens to be in
the established state the window probe is sent to the peer to
'unlock' the connection.

* TCP_REPAIR_QUEUE sockoption

This one sets the queue which we're about to repair. The
'no-queue' is set by default.

* TCP_QUEUE_SEQ socoption

Sets the write_seq/rcv_nxt of a selected repaired queue.
Allowed for TCP_CLOSE-d sockets only. When the socket changes
its state the other seq-s are changed by the kernel according
to the protocol rules (most of the existing code is actually
reused).

* Ability to forcibly bind a socket to a port

The sk->sk_reuse is set to SK_FORCE_REUSE.

* Immediate connect modification

The connect syscall initializes the connection, then directly jumps
to the code which finalizes it.

* Silent close modification

The close just aborts the connection (similar to SO_LINGER with 0
time) but without sending any FIN/RST-s to peer.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ee995283
    • P
      tcp: Move code around · 370816ae
      由 Pavel Emelyanov 提交于 
      This is just the preparation patch, which makes the needed for
TCP repair code ready for use.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      370816ae
    • P
      sock: Introduce named constants for sk_reuse · 4a17fd52
      由 Pavel Emelyanov 提交于 
      Name them in a "backward compatible" manner, i.e. reuse or not
are still 1 and 0 respectively. The reuse value of 2 means that
the socket with it will forcibly reuse everyone else's port.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4a17fd52
  5. 21 4月, 2012 7 次提交
  7. 20 4月, 2012 1 次提交
  9. 19 4月, 2012 1 次提交
  11. 18 4月, 2012 1 次提交
  13. 16 4月, 2012 2 次提交
  15. 15 4月, 2012 5 次提交
  17. 14 4月, 2012 1 次提交
    • E
      udp: intoduce udp_encap_needed static_key · 447167bf
      由 Eric Dumazet 提交于 
      Most machines dont use UDP encapsulation (L2TP)

Adds a static_key so that udp_queue_rcv_skb() doesnt have to perform a
test if L2TP never setup the encap_rcv on a socket.

Idea of this patch came after Simon Horman proposal to add a hook on TCP
as well.

If static_key is not yet enabled, the fast path does a single JMP .

When static_key is enabled, JMP destination is patched to reach the real
encap_type/encap_rcv logic, possibly adding cache misses.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: dev@openvswitch.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      447167bf
  19. 11 4月, 2012 3 次提交
    • E
      tcp: avoid order-1 allocations on wifi and tx path · a21d4572
      由 Eric Dumazet 提交于 
      Marc Merlin reported many order-1 allocations failures in TX path on its
wireless setup, that dont make any sense with MTU=1500 network, and non
SG capable hardware.

After investigation, it turns out TCP uses sk_stream_alloc_skb() and
used as a convention skb_tailroom(skb) to know how many bytes of data
payload could be put in this skb (for non SG capable devices)

Note : these skb used kmalloc-4096 (MTU=1500 + MAX_HEADER +
sizeof(struct skb_shared_info) being above 2048)

Later, mac80211 layer need to add some bytes at the tail of skb
(IEEE80211_ENCRYPT_TAILROOM = 18 bytes) and since no more tailroom is
available has to call pskb_expand_head() and request order-1
allocations.

This patch changes sk_stream_alloc_skb() so that only
sk->sk_prot->max_header bytes of headroom are reserved, and use a new
skb field, avail_size to hold the data payload limit.

This way, order-0 allocations done by TCP stack can leave more than 2 KB
of tailroom and no more allocation is performed in mac80211 layer (or
any layer needing some tailroom)

avail_size is unioned with mark/dropcount, since mark will be set later
in IP stack for output packets. Therefore, skb size is unchanged.
Reported-by: NMarc MERLIN <marc@merlins.org>
Tested-by: NMarc MERLIN <marc@merlins.org>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a21d4572
    • N
      tcp: fix tcp_rcv_rtt_update() use of an unscaled RTT sample · 18a223e0
      由 Neal Cardwell 提交于 
      Fix a code path in tcp_rcv_rtt_update() that was comparing scaled and
unscaled RTT samples.

The intent in the code was to only use the 'm' measurement if it was a
new minimum.  However, since 'm' had not yet been shifted left 3 bits
but 'new_sample' had, this comparison would nearly always succeed,
leading us to erroneously set our receive-side RTT estimate to the 'm'
sample when that sample could be nearly 8x too high to use.

The overall effect is to often cause the receive-side RTT estimate to
be significantly too large (up to 40% too large for brief periods in
my tests).
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      18a223e0
    • E
      tcp: restore correct limit · 5fb84b14
      由 Eric Dumazet 提交于 
      Commit c43b874d (tcp: properly initialize tcp memory limits) tried
to fix a regression added in commits 4acb4190 & 3dc43e3e,
but still get it wrong.

Result is machines with low amount of memory have too small tcp_rmem[2]
value and slow tcp receives : Per socket limit being 1/1024 of memory
instead of 1/128 in old kernels, so rcv window is capped to small
values.

Fix this to match comment and previous behavior.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5fb84b14
  21. 10 4月, 2012 2 次提交
  23. 06 4月, 2012 2 次提交
  25. 05 4月, 2012 2 次提交
  27. 04 4月, 2012 1 次提交
    • E
      tcp: allow splice() to build full TSO packets · 2f533844
      由 Eric Dumazet 提交于 
      vmsplice()/splice(pipe, socket) call do_tcp_sendpages() one page at a
time, adding at most 4096 bytes to an skb. (assuming PAGE_SIZE=4096)

The call to tcp_push() at the end of do_tcp_sendpages() forces an
immediate xmit when pipe is not already filled, and tso_fragment() try
to split these skb to MSS multiples.

4096 bytes are usually split in a skb with 2 MSS, and a remaining
sub-mss skb (assuming MTU=1500)

This makes slow start suboptimal because many small frames are sent to
qdisc/driver layers instead of big ones (constrained by cwnd and packets
in flight of course)

In fact, applications using sendmsg() (adding an additional memory copy)
instead of vmsplice()/splice()/sendfile() are a bit faster because of
this anomaly, especially if serving small files in environments with
large initial [c]wnd.

Call tcp_push() only if MSG_MORE is not set in the flags parameter.

This bit is automatically provided by splice() internals but for the
last page, or on all pages if user specified SPLICE_F_MORE splice()
flag.

In some workloads, this can reduce number of sent logical packets by an
order of magnitude, making zero-copy TCP actually faster than
one-copy :)
Reported-by: NTom Herbert <therbert@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail&gt;com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2f533844
  29. 02 4月, 2012 2 次提交
  31. 29 3月, 2012 1 次提交
  33. 28 3月, 2012 1 次提交
    • B
      net/ipv4: fix IPv4 multicast over network namespaces · 4e7b2f14
      由 Benjamin LaHaise 提交于 
      When using multicast over a local bridge feeding a number of LXC guests
using veth, the LXC guests are unable to get a response from other guests
when pinging 224.0.0.1.  Multicast packets did not appear to be getting
delivered to the network namespaces of the guest hosts, and further
inspection showed that the incoming route was pointing to the loopback
device of the host, not the guest.  This lead to the wrong network namespace
being picked up by sockets (like ICMP).  Fix this by using the correct
network namespace when creating the inbound route entry.
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4e7b2f14