Based on a patch by Jon Mason (see URL below).

All users of pcie_bus_configure_settings() pass arguments of the form
"bus, bus->self->pcie_mpss".  The "mpss" argument is redundant since we
can easily look it up internally.  In addition, all callers check
"bus->self" for NULL, which we can also do internally.

This patch simplifies the interface and the callers.  No functional change.

Reference: http://lkml.kernel.org/r/1317048850-30728-2-git-send-email-mason@myri.comSigned-off-by: NBjorn Helgaas <bhelgaas@google.com>

When EEH error happens to one specific PE, the device drivers
of its attached EEH devices (PCI devices) are checked to see
the further action: reset with complete hotplug, or reset without
hotplug. However, that's not enough for those PCI devices whose
drivers can't support EEH, or those PCI devices without driver.
So we need do so-called "partial hotplug" on basis of PCI devices.
In the situation, part of PCI devices of the specific PE are
unplugged and plugged again after PE reset.

The patch changes pcibios_add_pci_devices() so that it can support
full hotplug and so-called "partial" hotplug based on device-tree
or real hardware. It's notable that pci_of_scan.c has been changed
for a bit in order to support the "partial" hotplug based on dev-tree.

Most of the generic code already supports that, we just need to
plumb it properly on our side.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 37f02195 (powerpc/pci: fix PCI-e devices rescan issue on powerpc
platform) fixes a problem with interrupt and DMA initialization on hot
plugged devices. With this commit, interrupt and DMA initialization for
hot plugged devices is handled in the pci device enable function.

This approach has a couple of drawbacks. First, it creates two code paths
for device initialization, one for hot plugged devices and another for devices
known during the initial PCI scan. Second, the initialization code for hot
plugged devices is only called when the device is enabled, ie typically
in the probe function. Also, the platform specific setup code is called each
time pci_enable_device() is called, not only once during device discovery,
meaning it is actually called multiple times, once for devices discovered
during the initial scan and again each time a driver is re-loaded.

The visible result is that interrupt pins are only assigned to hot plugged
devices when the device driver is loaded. Effectively this changes the PCI
probe API, since pci_dev->irq and the device's dma configuration will now
only be valid after pci_enable() was called at least once. A more subtle
change is that platform specific PCI device setup is moved from device
discovery into the driver's probe function, more specifically into the
pci_enable_device() call.

To fix the inconsistencies, add new function pcibios_add_device.
Call pcibios_setup_device from pcibios_setup_bus_devices if device setup
is not complete, and from pcibios_add_device if bus setup is complete.

With this change, device setup code is moved back into device initialization,
and called exactly once for both static and hot plugged devices.

[ This also fixes a regression introduced by the above patch which
  causes dev->irq to be overwritten under some cirumstances after
  MSIs have been enabled for the device which leads to crashes due
  to the MSI core "hijacking" dev->irq to store the base MSI number
  and not the LSI. --BenH
]

Cc: Yuanquan Chen <Yuanquan.Chen@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hiroo Matsumoto <matsumoto.hiroo@jp.fujitsu.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If a BAR has the value of 0, we would assume that it is unset yet and
then mark the resource as unset and would reassign it later. But after
commit 6c5705fe (powerpc/PCI: get rid of device resource fixups)
the pcibios_fixup_resources is invoked after the bus address was
translated to linux resource. So the value of res->start is resource
address. And since the resource and bus address may be different, we
should translate it to the bus address before doing the check.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The codes which ever used these two variables have gone. Throw away
them too.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

These comments already don't apply to the current code. So just remove
them.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The message is only meant to be displayed if resource 0 is empty,
but was displayed if any is.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The PCI core supports an offset per aperture nowadays but our arch
code still has a single offset per host bridge representing the
difference betwen CPU memory addresses and PCI MMIO addresses.

This is a problem as new machines and hypervisor versions are
coming out where the 64-bit windows will have a different offset
(basically mapped 1:1) from the 32-bit windows.

This fixes it by using separate offsets. In the long run, we probably
want to get rid of that intermediary struct pci_controller and have
those directly stored into the pci_host_bridge as they are parsed
but this will be a more invasive change.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When converting to use the new pci_add_resource_offset() we didn't
properly account for empty resources (0 flags) and add those bogons
to the PHBs. The result is some annoying messages in the log.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On pseries machines the detection for max_bus_speed should be done
through an OpenFirmware property. This patch adds a function to perform
this detection and a hook to perform dynamic adding of the function only
for pseries. This is done by overwriting the weak
pcibios_root_bridge_prepare function which is called by
pci_create_root_bus().

From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Add a PCI quirk for VGA devices on Power to set the default VGA device.
Ensures a default VGA is always set if a graphics adapter is present,
even if firmware did not initialize it. If more than one graphics
adapter is present, ensure the one initialized by firmware is set
as the default VGA device. This ensures that X autoconfiguration
will work.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>

Powerpc initializes the DMA and IRQ information in pci_scan_child_bus()->
pcibios_fixup_bus()->pcibios_setup_bus_devices(). But for the devices
which are hotpluged, bus->is added has been set for the first scan of the
PCI-e bus, so the initialization code won't be called. Then the hotpluged
devices' driver will fail to load.

For example :
The PCI-e device 0001:03:00.0 is the Intel PCI-e e1000e network card, remove
it from the system:

    # echo 1 > /sys/bus/pci/devices/0001\:03\:00.0/remove
    # e1000e 0001:03:00.0 eth0: removed PHC

Rescan it from it's bus:

    # echo 1 > /sys/bus/pci/devices/0001\:02\:00.0/rescan
    ...
    e1000e 0001:03:00.0: Disabling ASPM L0s L1
    e1000e 0001:03:00.0: No usable DMA configuration, aborting
    e1000e: probe of 0001:03:00.0 failed with error -5

So we move the DMA & IRQ initialization code from pcibios_setup_devices() and
construct a new function pcibios_enable_device. We call this function in
pcibios_enable_device, which will be called by PCI-e rescan code. At the
meanwhile, we avoid the the impact on cardbus. I also validate this patch with
silicon's PCIe-sata which encounters the IRQ issue.
Signed-off-by: NYuanquan Chen <Yuanquan.Chen@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hiroo Matsumoto <matsumoto.hiroo@jp.fujitsu.com>
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>

The DDW code uses a eeh_dev struct from the pci_dev. However, this is
not set until eeh_add_device_late is called.

Since pci_bus_add_devices is called before eeh_add_device_late, the PCI
devices are added to the bus, making drivers' probe hooks to be called.
These will call set_dma_mask, which will call the DDW code, which will
require the eeh_dev struct from pci_dev. This would result in a crash,
due to a NULL dereference.

Calling eeh_add_device_late after pci_bus_add_devices would make the
system BUG, because device files shouldn't be added to devices there
were not added to the system. So, a new function is needed to add such
files only after pci_bus_add_devices have been called.

Cc: stable@vger.kernel.org
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

CONFIG_HOTPLUG is going away as an option.  As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove conditional code based on CONFIG_HOTPLUG being false.  It's
always on now in preparation of it going away as an option.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch implements pcibios_window_alignment() so powerpc platforms can
force P2P bridge windows to be at larger alignments than the PCI spec
requires.

[bhelgaas: changelog]
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

When PCI probe flag PCI_REASSIGN_ALL_RSRC has been passed into PCI
core, it's hoped that all resources to be reassigned by PCI core.
As to particular P2P (PCI-to-PCI) bridge, the size of the corresponding
BAR (I/O, MMIO, prefetchable MMIO) is calculated by the resources
required by the PCI devices behind the P2P bridge. That means that
the information like start/end address retrieved from the hardware
registers of the P2P bridge is meainingless in the case. However,
we still count that in and the BARs might have been configured by
firmware with non-zero size. That leads to space waste.

The patch explicitly sets the size of P2P bridge BARs to zero in
case that resource reassignment is expected with PCI probe flag
PCI_REASSIGN_ALL_RSRC. In the result, it will save overall resource
required by the system without waste.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The pattern (np ? np->full_name : "<none>") is rather common in the
kernel, but can also make for quite long lines.  This patch adds a new
inline function, of_node_full_name() so that the test for a valid node
pointer doesn't need to be open coded at all call sites.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

The PCI core provides a generic pcibios_setup() routine.  Drop this
architecture-specific version in favor of that.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMyron Stowe <myron.stowe@redhat.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

While creating the PCI root bus through function pci_create_root_bus()
of PCI core, it should have assigned the secondary bus number for the
newly created PCI root bus. Thus we needn't do the explicit assignment
for the secondary bus number again in pcibios_scan_phb().
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The pattern (np ? np->full_name : "<none>") is rather common in the
kernel, but can also make for quite long lines.  This patch adds a new
inline function, of_node_full_name() so that the test for a valid node
pointer doesn't need to be open coded at all call sites.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>

Add the host bridge bus number aperture to the resource list.
Like the MMIO and I/O port apertures, this is used when assigning
resources to hot-added devices or in the case of conflicts.

[bhelgaas: changelog]
CC: Paul Mackerras <paulus@samba.org>
CC: linuxppc-dev@lists.ozlabs.org
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Replace the struct pci_bus secondary/subordinate members with the
struct resource busn_res.  Later we'll build a resource tree of these
bus numbers.

[bhelgaas: changelog]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

This is no longer selectable, so just remove all the dependent code.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Make sure we compute CPU addresses (resource start/end) the same way both
when we set up the I/O aperture (hose->io_resource) and when we use
pcibios_bus_to_resource() to convert BAR values into resources.

This fixes a build failure ("cast from pointer to integer of different
size" in configs where resource_size_t is 64 bits but pointers are 32 bits)
I introduced in 6c5705fe.
Acked-By: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.

CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

We already use pci_flags, so this just sets pci_flags directly and removes
the intermediate step of figuring out pci_probe_only, then using it to set
pci_flags.

The PCI core provides a pci_flags definition (currently __weak), so drop
the powerpc definitions in favor of that.

CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Convert from pci_create_bus() to pci_create_root_bus().  This way the root
bus resources are correct immediately.  This patch doesn't fix a problem
because powerpc fixed the resources before scanning the bus, but it makes
powerpc more consistent with other architectures.

v2: fix build error with resource pointer passing

CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch converts PowerPC's architecture-specific
'pcibios_set_master()' routine to a non-inlined function.  This will
allow follow on patches to create a generic 'pcibios_set_master()'
function using the '__weak' attribute which can be used by all
architectures as a default which, if necessary, can then be over-
ridden by architecture-specific code.

Converting 'pci_bios_set_master()' to a non-inlined function will
allow PowerPC's 'pcibios_set_master()' implementation to remain
architecture-specific after the generic version is introduced and
thus, not change current behavior.

No functional change.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMyron Stowe <myron.stowe@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

It's only used inside the same file where it's defined. There's
also no point exporting it anymore.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When PCI_REASSIGN_ALL_RSRC is set, we used to clear all bus resources
at the beginning of survey and re-allocate them later.

This changes it so instead, during early fixup, we mark all resources
as IORESOURCE_UNSET and move them down to be 0-based.

Later, if bus resources are still unset at the beginning of the survey,
then we clear them.

This shouldn't impact the re-assignment case on 4xx, but will enable
us to have the platform do some custom resource assignment before the
survey, by clearing individual resources IORESOURCE_UNSET bit.

Also limits the clutter in the kernel log from fixup when re-assigning
since we don't care about the offset applied to the BAR values in this
case.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Some platforms need to perform resource allocation using a custom algorithm
due to HW constraints, or may want to tweak things globally below a host
bridge. For example OPAL support for IODA will need to perform a
resource allocation pass that applies IODA specific segmentation
constraints to MMIO which cannot be done simply using the kernel generic
resource management code.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Current pci/pcie init code will hide the pci/pcie host resource.
But did not judge it is host/RC or agent/EP. If configured as
agent/EP, we should avoid hiding its resource in the host side.

In PCI system, the Programing Interface can be used to judge the
host/agent status:
Programing Interface = 0: host
Programing Interface = 1: Agent

In PCIE system, both the Programing Interface and Header type can
be used to judge the RC/EP status.
Header Type = 0: EP
Header Type = 1: RC
Signed-off-by: NJason Jin <Jason.jin@freescale.com>
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NJia Hongtao <B38951@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

We don't want to configure PCI Express Max Payload Size or
Max Read Request Size on systems that set that flag. The
firmware will have done it for us, and under hypervisors such
as pHyp we don't even see the parent switches and bridges and
thus can make no assumption on what values are safe to use.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This new function is used to properly setup the PCI Express Max Payload Size
(and in some circumstances Max Read Request Size).

Some systems will not operate properly if these aren't set correctly and
the firmware doesn't always do it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This renames pci flags functions and enums in preparation for creating
generic version in asm-generic/pci-bridge.h. The following search and
replace is done:

s/ppc_pci_/pci_/
s/PPC_PCI_/PCI_/

Direct accesses to ppc_pci_flag variable are replaced with helper
functions.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>

We need the FSL specific header fixup code on both 32-bit and 64-bit
platforms so just move the code into pci-common.c.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>