The PB1100/1500 are similar to their DB-cousins but with a few
more devices on the bus.

This patch adds PB1100/1500 support to the existing DB1100/1500
code.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: lnux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4338/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The PB1550 is more or less a DB1550 without the PCI IDE controller,
a more complicated (read: configurable) Flash setup and some other
minor changes.  Like the DB1550 it can be automatically detected by
reading the CPLD ID register bits.

This patch adds PB1550 detection and setup to the DB1550 code.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4337/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Combine support for the DB1200/PB1200, DB1300 and DB1550 boards into
a single kernel image.

defconfig-generated image verified on DB1200, DB1300 and DB1550.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4335/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

move contents to already existing platform.c file.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3287/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

These 3 boards are very similar; with this patch a single kernel image
which runs on all three can be built.

Tested on DB1500 and DB1100.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2872/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The PB1200 is basically a DB1200 with additional MMC and camera sockets
and different base addresses for external hardware (CPLD, IDE, Net, NAND).

This patch implements the missing PB1200 features in DB1200 support code
and runtime board detection.

Tested on DB1200 only.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2880/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2884/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2868/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2867/
Patchwork: https://patchwork.linux-mips.org/patch/2919/
Patchwork: https://patchwork.linux-mips.org/patch/2928/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

No test hardware and no (apparent) users.  These boards seem very
similar to the DB1500, so if required support can be brought back
again (I have datasheets) but then with dedicated board code, not
tacked on to DB1000 support.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2864/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Noone seems to have test hardware or care anymore.  Drop PB1000 support
and along with it the old Alchemy PCMCIA socket driver.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Cc: linux-pcmcia@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/2881/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

[Ralf: Remove a forgotten -Werror in Pb1200 Makefile.]
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1319/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Create own directory for DB1200 code and update it with new features.

- SPI support:
  - tmp121 temperature sensor
  - SPI flash on DB1200
- I2C support
  - NE1619 sensor
  - AT24 eeprom
- I2C/SPI can be selected at boot time via switch S6.8
- Carddetect IRQs for SD cards.
- gen_nand based NAND support.
- hexleds count sleep/wake transitions.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Warnings being suppressed, we can now turn on -Werror for boards which did
not have it already (devboards and xss1500).
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Register the PCMCIA driver on all boards supported by it,
get rid of now-unused pcmcia macros in the board headers
(and subsequently empty pb1100/pb1500 ones).
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

All Alchemy development boards have external CPLDs with a few registers
in them.  They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.

This patch
- adds a primitive facility to initialize and use these external
  registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
  functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
  headers in a central place.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Replace the current sysctl-based suspend interface with a new sysfs-
based one which also uses the Linux-2.6 suspend model.

To configure wakeup sources, a subtree for the demoboards is created
under /sys/power/db1x:

sys/
`-- power
    `-- db1x
        |-- gpio0
        |-- gpio1
        |-- gpio2
        |-- gpio3
        |-- gpio4
        |-- gpio5
        |-- gpio6
        |-- gpio7
        |-- timer
        |-- timer_timeout
        |-- wakemsk
        `-- wakesrc

The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register.  Writing '1'
enables a wakesource, 0 disables it.

The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.

The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.

For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:

echo 10 > /sys/power/db1x/timer_timeout
echo 1 > /sys/power/db1x/timer
echo mem > /sys/power/sleep

This patch also removes the homebrew CPU frequency switching code.  I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 create mode 100644 arch/mips/alchemy/devboards/pm.c

Share some code and merge small files:
- Extract the prom init code from all devboard files (they only differ in
  memory configuration).
- Merge the irq configuration into board setup code.
- Merge smaller files into board setup code.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 delete mode 100644 arch/mips/alchemy/devboards/db1x00/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1000/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1000/irqmap.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1100/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1100/irqmap.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1200/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1500/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1500/irqmap.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1550/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1550/irqmap.c
 create mode 100644 arch/mips/alchemy/devboards/prom.c

This should ease sharing of common devboard code.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>