Skip to content

K
kernel_linux

OpenHarmony / kernel_linux
上一次同步 4 年多

通知 15
Star 8
Fork 2
K
kernel_linux
切换分支/标签
  1. 26 6月, 2008 1 次提交
  3. 06 2月, 2008 1 次提交
  5. 21 7月, 2007 1 次提交
  7. 24 4月, 2007 1 次提交
  9. 24 1月, 2007 1 次提交
  11. 04 12月, 2006 2 次提交
    • A
      [POWERPC] ps3: multiplatform build fixes · e22ba7e3
      由 Arnd Bergmann 提交于 
      A few code paths need to check whether or not they are running
on the PS3's LV1 hypervisor before making hcalls. This introduces
a new firmware feature bit for this, FW_FEATURE_PS3_LV1.

Now when both PS3 and IBM_CELL_BLADE are enabled, but not PSERIES,
FW_FEATURE_PS3_LV1 and FW_FEATURE_LPAR get enabled at compile time,
which is a bug. The same problem can also happen for (PPC_ISERIES &&
!PPC_PSERIES && PPC_SOMETHING_ELSE). In order to solve this, I
introduce a new CONFIG_PPC_NATIVE option that is set when at least
one platform is selected that can run without a hypervisor and then
turns the firmware feature check into a run-time option.

The new cell oprofile support that was recently merged does not
work on hypervisor based platforms like the PS3, therefore make
it depend on PPC_CELL_NATIVE instead of PPC_CELL. This may change
if we get oprofile support for PS3.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
      e22ba7e3
    • M
      [POWERPC] cell: Add oprofile support · 18f2190d
      由 Maynard Johnson 提交于 
      Add PPU event-based and cycle-based profiling support to Oprofile for Cell.

Oprofile is expected to collect data on all CPUs simultaneously.
However, there is one set of performance counters per node.  There are
two hardware threads or virtual CPUs on each node.  Hence, OProfile must
multiplex in time the performance counter collection on the two virtual
CPUs.

The multiplexing of the performance counters is done by a virtual
counter routine.  Initially, the counters are configured to collect data
on the even CPUs in the system, one CPU per node.  In order to capture
the PC for the virtual CPU when the performance counter interrupt occurs
(the specified number of events between samples has occurred), the even
processors are configured to handle the performance counter interrupts
for their node.  The virtual counter routine is called via a kernel
timer after the virtual sample time.  The routine stops the counters,
saves the current counts, loads the last counts for the other virtual
CPU on the node, sets interrupts to be handled by the other virtual CPU
and restarts the counters, the virtual timer routine is scheduled to run
again.  The virtual sample time is kept relatively small to make sure
sampling occurs on both CPUs on the node with a relatively small
granularity.  Whenever the counters overflow, the performance counter
interrupt is called to collect the PC for the CPU where data is being
collected.

The oprofile driver relies on a firmware RTAS call to setup the debug bus
to route the desired signals to the performance counter hardware to be
counted.  The RTAS call must set the routing registers appropriately in
each of the islands to pass the signals down the debug bus as well as
routing the signals from a particular island onto the bus.  There is a
second firmware RTAS call to reset the debug bus to the non pass thru
state when the counters are not in use.
Signed-off-by: NCarl Love <carll@us.ibm.com>
Signed-off-by: NMaynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      18f2190d
  13. 01 11月, 2006 1 次提交
    • A
      [POWERPC] Fix oprofile support for e500 in arch/powerpc · dd6c89f6
      由 Andy Fleming 提交于 
      Fixed a compile error in building the 85xx support with oprofile, and in
the process cleaned up some issues with the fsl_booke performance monitor
code.

* Reorganized FSL Book-E performance monitoring code so that the 7450
  wouldn't be built if the e500 was, and cleaned it up so it was more
  self-contained.

* Added a cpu_setup function for FSL Book-E.  The original
  cpu_setup function prototype had no arguments, assuming that
  the reg_setup function would copy the required information into
  variables which represented the registers.  This was silly for
  e500, since it has 1 register per counter (rather than 3 for
  all counters), so the code has been restructured to have
  cpu_setup take the current counter config array as an argument,
  with op_powerpc_setup() invoking op_powerpc_cpu_setup() through
  on_each_cpu(), and op_powerpc_cpu_setup() invoking the
  model-specific cpu_setup function with an argument.  The
  argument is ignored on all other platforms at present.

* Fixed a confusing line where a trinary operator only had two
  arguments
Signed-off-by: NAndrew Fleming <afleming@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      dd6c89f6
  15. 27 6月, 2006 1 次提交
  17. 21 6月, 2006 1 次提交
  19. 22 4月, 2006 1 次提交
  21. 29 3月, 2006 2 次提交
  23. 14 1月, 2006 1 次提交
    • A
      [PATCH] powerpc: oprofile cpu type names clash with other code · 7a45fb19
      由 Andy Whitcroft 提交于 
      In 2.6.15-git6 a change was commited in the oprofile support in
the powerpc architecture.  It introduced the powerpc_oprofile_type
which contains the define G4.  This causes a name clash with the
existing wacom usb tablet driver.

      CC [M]  drivers/usb/input/wacom.o
    drivers/usb/input/wacom.c:98: error: conflicting types for `G4'
    include/asm/cputable.h:37: error: previous declaration of `G4'
      CC [M]  drivers/usb/mon/mon_text.o
    make[3]: *** [drivers/usb/input/wacom.o] Error 1
    make[2]: *** [drivers/usb/input] Error 2

The elements of an enum declared in global scope are effectivly
global identifiers themselves.  As such we need to ensure the names
are unique.  This patch updates the later oprofile support to use
unique names.
Signed-off-by: NAndy Whitcroft <apw@shadowen.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      7a45fb19
  25. 09 1月, 2006 2 次提交
  27. 20 10月, 2005 1 次提交
    • D
      [PATCH] powerpc: Merge ppc64 pmc.[ch] with ppc32 perfmon.[ch] · f7f6f4fe
      由 David Gibson 提交于 
      This patches the ppc32 and ppc64 versions of the headers and .c files
with helper functions for manipulating the performance counting
hardware.  As a side effect, it removes use of the term "perfmon" from
ppc32, thus avoiding confusion with the unrelated performance counter
interface from HP Labs also called "perfmon".

Built, but not booted, for g5, pSeries, iSeries, and 32-bit Powermac
with both ARCH=powerpc and ARCH=ppc{,64} as appropriate.
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      f7f6f4fe
  29. 28 9月, 2005 1 次提交
  31. 21 9月, 2005 3 次提交
  33. 06 9月, 2005 4 次提交
  35. 30 8月, 2005 1 次提交
  37. 17 4月, 2005 1 次提交
    • L
      Linux-2.6.12-rc2 · 1da177e4
      由 Linus Torvalds 提交于 
      Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
      1da177e4