The interrupts have already been cleared, so we don't need to clear them
again. Also, we could miss interrupts if they are cleared, but we don't
process the packet.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The standard readl/writel accessors involve a spinlock and cache sync
operation on ARM platforms with an outer cache. Only DMA triggering
accesses need this, so use the raw variants instead in the critical paths.

The relaxed variants would be more appropriate, but don't exist on all
arches.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New received frames will trigger the rx DMA to poll the DMA descriptors,
so there is no need to tell the h/w to poll. We also want to enable
dropping frames from the fifo when there is no buffer.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the tx dma to start reading the next frame while sending the current
frame.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 56b765b7 (htb: improved accuracy at high rates)
introduced two bugs :

1) one bstats_update() was inadvertently removed from
   htb_dequeue_tree(), breaking statistics/rate estimation.

2) Missing qdisc_put_rtab() calls in htb_change_class(),
   leaking kernel memory, now struct htb_class no longer
   retains pointers to qdisc_rate_table structs.

   Since only rate is used, dont use qdisc_get_rtab() calls
   copying data we ignore anyway.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Vimalkumar <j.vimal@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

instead of making separate tg3_napi_disable() and netif_tx_disable() calls.

Update version to 3.126.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for 5717C0 which is a 5720A0 with special bonds-out option.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed some coding style issues.
Signed-off-by: NKumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

checkpatch.pl throws error message for the current code. This patch fixes
this coding style issue.
Signed-off-by: NKumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: NJitendra Kalsaria <Jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a follow-up for patch "net: filter: add vlan tag access"
to support the new VLAN_TAG/VLAN_TAG_PRESENT accessors in BPF JIT.
Signed-off-by: NDaniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following chips need to enable internal settings to let ASPM
and clock request work.

RTL8111E-VL, RTL8111F, RTL8411, RTL8111G
RTL8105, RTL8402, RTL8106
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of issuing (0) statements when !CONFIG_SYSFS which will cause
'warning: ', we'll use inline statements instead. This will effectively
do the same thing, but suppress any unnecessary warnings.

Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: bridge@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use WARN rather than printk followed by WARN_ON(1), for conciseness.

A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression list es;
@@

-printk(
+WARN(1,
  es);
-WARN_ON(1);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Building atp.o triggers this GCC warning:
    drivers/net/ethernet/realtek/atp.c: In function ‘set_rx_mode’:
    drivers/net/ethernet/realtek/atp.c:871:26: warning: ‘mc_filter[0]’ may be used uninitialized in this function [-Wuninitialized]

GCC is correct. In promiscuous mode 'mc_filter' will be used
uninitialized in set_rx_mode_8012(), which is apparently inlined into
set_rx_mode().

But it turns out set_rx_mode_8012() will never be called, since
net_local.chip_type will always be RTL8002. So we can just remove
set_rx_mode_8012() and do some related cleanups.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CPSW driver remaps two different IO regions, but fails to unmap them
both. This patch fixes the issue by calling iounmap in the appropriate
places.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code mixes up the CPSW_SS and the CPSW_WR register naming. This patch
changes the names to conform to the published Technical Reference Manual
from TI, in order to make working on the code less confusing.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bridge notify hook rtnl_bridge_notify() was not handling the
case where the master flags was set or with both flags set. First
flags are not being passed correctly and second the logic to parse
them is broken.

This patch passes the original flags value and fixes the
logic.
Reported-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When underlying phy driver restores its state very fast after being brought
down and up so that macb driver function macb_handle_link_change() was never
called with link state "down", driver's internal representation of phy speed
and duplex (bp->speed and bp->duplex) didn't change. So, macb driver sees no
reason to perform actual write to the NCFGR register, although the speed and
duplex settings in that register were reset when interface was brought down
and up. In that case actual phy speed and duplex differ from NCFGR settings.
The patch fixes that by keeping internal driver representation of speed and
duplex in sync with actual content of NCFGR.
Signed-off-by: NVitalii Demianets <vitas@nppfactor.kiev.ua>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ben Hutchings recently came up with a better way to handle the kconfig
dependencies for the PTP hardware clocks. This patch converts one new and
one older driver to the new scheme.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current HTB (and TBF) uses rate table computed by the "tc"
userspace program, which has the following issue:

The rate table has 256 entries to map packet lengths
to token (time units).  With TSO sized packets, the
256 entry granularity leads to loss/gain of rate,
making the token bucket inaccurate.

Thus, instead of relying on rate table, this patch
explicitly computes the time and accounts for packet
transmission times with nanosecond granularity.

This greatly improves accuracy of HTB with a wide
range of packet sizes.

Example:

tc qdisc add dev $dev root handle 1: \
        htb default 1

tc class add dev $dev classid 1:1 parent 1: \
        rate 5Gbit mtu 64k

Here is an example of inaccuracy:

$ iperf -c host -t 10 -i 1

With old htb:
eth4:   34.76 Mb/s In  5827.98 Mb/s Out -  65836.0 p/s In  481273.0 p/s Out
[SUM]  9.0-10.0 sec   669 MBytes  5.61 Gbits/sec
[SUM]  0.0-10.0 sec  6.50 GBytes  5.58 Gbits/sec

With new htb:
eth4:   28.36 Mb/s In  5208.06 Mb/s Out -  53704.0 p/s In  430076.0 p/s Out
[SUM]  9.0-10.0 sec   594 MBytes  4.98 Gbits/sec
[SUM]  0.0-10.0 sec  5.80 GBytes  4.98 Gbits/sec

The bits per second on the wire is still 5200Mb/s with new HTB
because qdisc accounts for packet length using skb->len, which
is smaller than total bytes on the wire if GSO is used.  But
that is for another patch regardless of how time is accounted.

Many thanks to Eric Dumazet for review and feedback.
Signed-off-by: NVimalkumar <j.vimal@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"ip link add ... type vxlan ... ttl X" allows a user to set the TTL
used by a VXLAN for encapsulation. The provided value was ignored by
vxlan module and the default value of 1 was used when encapsulating
multicast packets.
Signed-off-by: NVincent Bernat <bernat@luffy.cx>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for wol wakeup on unicast, broadcast,
multicast and arp frames.
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Ethertype 0x4305 (not an officially registered id).
This Ethertype is used by every frame generated by B.A.T.M.A.N.-Advanced. Its
definition is currently batman-adv local only and since it is not officially
registered it is better to make its definition kernel-wide so that we avoid
collisions given by future unofficial uses of the same Ethertype.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After d58d46b5 (r8169: jumbo fixes.) max frame len is stored in
rtl_chip_infos[].jumbo_max for each chip and SafeMtu should be gone.
Signed-off-by: NKirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As suggested by Eric, we could introduce a helper function
for ipv6 too, to avoid checking if rt is NULL before
dst_release().

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can save a test in ip_rt_put(), considering dst_release() accepts
a NULL parameter, and dst is first element in rtable.

Add a BUILD_BUG_ON() to catch any change that could break this
assertion.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Cong Wang <amwang@redhat.com>
Acked-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lots of points in the sctp_cmd_interpreter function treat the sctp_cmd_t arg as
a void pointer, even though they are written as various other types.  Theres no
need for this as doing so just leads to possible type-punning issues that could
cause crashes, and if we remain type-consistent we can actually just remove the
void * member of the union entirely.

Change Notes:

v2)
	* Dropped chunk that modified SCTP_NULL to create a marker pattern
	 should anyone try to use a SCTP_NULL() assigned sctp_arg_t, Assigning
	 to .zero provides the same effect and should be faster, per Vlad Y.

v3)
	* Reverted part of V2, opting to use memset instead of .zero, so that
	 the entire union is initalized thus avoiding the i164 speculative load
	 problems previously encountered, per Dave M..  Also rewrote
	 SCTP_[NO]FORCE so as to use common infrastructure a little more

Signed-off-by: Neil Horman <nhorman@tuxdriver.com
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-sctp@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In dev_forward_change(), it is useless to check if idev->dev
is NULL, it is always non-NULL here.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some years ago, the ktime_t helper functions ktime_now() and ktime_lt()
have been introduced. Instead of defining them inside pktgen.c, they
should either use ktime_t library functions or, if not available, they
should be defined in ktime.h, so that also others can benefit from them.
ktime_compare() is introduced with a similar notion as in timespec_compare().
Signed-off-by: NDaniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For passive TCP connections using TCP_DEFER_ACCEPT facility,
we incorrectly increment req->retrans each time timeout triggers
while no SYNACK is sent.

SYNACK are not sent for TCP_DEFER_ACCEPT that were established (for
which we received the ACK from client). Only the last SYNACK is sent
so that we can receive again an ACK from client, to move the req into
accept queue. We plan to change this later to avoid the useless
retransmit (and potential problem as this SYNACK could be lost)

TCP_INFO later gives wrong information to user, claiming imaginary
retransmits.

Decouple req->retrans field into two independent fields :

num_retrans : number of retransmit
num_timeout : number of timeouts

num_timeout is the counter that is incremented at each timeout,
regardless of actual SYNACK being sent or not, and used to
compute the exponential timeout.

Introduce inet_rtx_syn_ack() helper to increment num_retrans
only if ->rtx_syn_ack() succeeded.

Use inet_rtx_syn_ack() from tcp_check_req() to increment num_retrans
when we re-send a SYNACK in answer to a (retransmitted) SYN.
Prior to this patch, we were not counting these retransmits.

Change tcp_v[46]_rtx_synack() to increment TCP_MIB_RETRANSSEGS
only if a synack packet was successfully queued.
Reported-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Vijay Subramanian <subramanian.vijay@gmail.com>
Cc: Elliott Hughes <enh@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e5a55a89 ('net: create generic
bridge ops') broke the handling of a non-zero starting index in
rtnl_bridge_getlink() (based on the old br_dump_ifinfo()).

When the starting index is non-zero, we need to increment the current
index for each entry that we are skipping.  Also, we need to check the
index before both cases, since we may previously have stopped
iteration between getting information about a device from its master
and from itself.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Tested-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fib6_add_rt2node() will reject the nexthop if this flag is set, so
we perform the check only for the first nexthop.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since this array is no longer part of the bridge driver, it should
have an 'eth' prefix not 'br'.

We also assume that either it's 16-bit-aligned or the architecture has
efficient unaligned access.  Ensure the first of these is true by
explicitly aligning it.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function name should include '_ether_addr'.
Return type should be bool.
Parameter name should be 'addr' not 'dest' (also matching kernel-doc).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Parse the string into an array of bytes rather than ints, so we can
use is_link_local() rather than reimplementing it.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was missed in commit a24006ed
('ptp: Enable clock drivers along with associated net/PHY drivers')
which enabled sfc's clock driver unconditionally.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>