The workaround which toggles the LANPHYPC (LAN PHY Power Control) value bit
to force the MAC-Phy interconnect into PCIe mode from SMBus mode during
driver load and resume should always be done except if PHY resets are
blocked by the Manageability Engine (ME).  Previously, the toggle was done
only if PHY resets are blocked and the ME was disabled.

The rest of the patch is just indentation changes as a consequence of the
updated workaround.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Internal stress testing with jumbo frames shows the reliability of ICH9 and
ICH10D devices is improved in certain corner cases by disabling the Early
Receive feature. To reduce the performance impact caused by disabling this
feature, the packet buffer sizes and relevant flow control settings are
modified accordingly.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Suggested by YOSHIFUJI Hideaki.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Otherwise (on sparc64):

drivers/net/ethernet/intel/e1000e/ethtool.c:657:3: error: implicit declaration of function 'vmalloc' [-Werror=implicit-function-declaration]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only semantic difference is that we now hold a reference to the
neighbour and thus have to release it.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the future the ipv4/ipv6 route gateway will take on two types
of values:

1) INADDR_ANY/IN6ADDR_ANY, for local network routes, and in this case
   the neighbour must be obtained using the destination address in
   ipv4/ipv6 header as the lookup key.

2) Everything else, the actual nexthop route address.

So if the gateway is not inaddr-any we use it, otherwise we must use
the packet's destination address.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It might be useful to get a counter of failed tcp_retransmit_skb()
calls.
Reported-by: NSatoru Moriya <satoru.moriya@hds.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocation of 64 bytes in skb headroom is not enough if we have to pull
ethernet + ipv6 + tcp headers, and/or extra tunneling header.

Its currently not noticed because netdev_alloc_skb_ip_align(64) give us
more room, thanks to power-of-two kmalloc() roundups.

Make sure we ask for 128 bytes so that side effects of upcoming patches
from Ian Campbell dont decrease benet rx performance, because of extra
skb head reallocations.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Cc: Vasundhara Volam <vasundhara.volam@emulex.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add statistics for tracking parity errors from which we successfully
recovered and those which were deemed unrecoverable.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Sample mcp pulse and mcp sequence in nic load instead of in init_one
as they may change by the time we want to use them.

2. Allow cnic to access device during nic load (by adding a new "LOADING" state
to recovery flow). This prevents the unnecessary cnic timeout which resulted
by cnic attempting to access because nic is loading, but being blocked because
of the Recovery state.

3. Issue 'fake' driver load command to mcp when last driver unloads to prevent
mcp from taking ownership. When recovery is complete unload fake driver to
allow mcp to initialize the hardware before first driver loads.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recovery register (to which a hardware lock has been added in previous
patch) is used amongst other things to track the active PFs. The old
implementation which used a per path counter is not viable in a virtualized
environment where a pf may increment the counter and then have the kernel
crash around it preventing the counter from ever reaching zero.
In the new implementation the scenario described will result in the PF timing
out against the mcp, which will clear the PF's bit in the bitmask allowing
recovery process to proceed.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use hardware locks to protect resources common to several Physical Functions. In
a virtualized environment the RTNL lock only protects a PF's driver against
the PFs sharing it's VMs with regard to device resources. Other PFs may reside
in other VMs under other OSs, and are not subject to the lock. Such resources
which were previously protected implicitly by the RTNL lock must now be
protected explicitly with dedicated HW locks.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a virtualized environment it is possible for a loading driver to discover
that Firmware is already loaded to the device, and that this FW does not match
its own. This can happen for example if different Physical Functions are
Assigned to different VMs in which different driver versions are loaded. The
code in this patch ensures that only drivers with matching FW are loaded over
the device, and that in the case described above where the Firmware version
doesn't match the driver load is aborted.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Fix bug where return value is ignored
2. Improve printouts
3. Fix typos
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BDF was obtained from kernel but since in virtualized environment
(e.g. physical device assigment in KVM) the function number may
not be the real one, the info must be obtained from the device.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In virtualized environments indirect access to the device may not be supported
(depending on the Hypervisor type). Indirect device access was used since in
some harware contexts (i.e. certain chipset and BIOS) every access the driver
makes across the pci is followed by a BIOS initiated Zero Length Read to the
same address. When accessing widebus registers this zero length read corrupts
the serialization of the read/write sequence resulting with errors. To avoid
this problem widebus registers are always accessed via the DMAE or the indirect
interface. However, the 57712x and 578xx devices intercept the zero length read
and so using the indirect interface with these devices is not necessary. Since
PDA is only supported for 57712x and 578xx the indirect access to device was
restricted to 57710 and 57711x.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the use of up to three hardware queues for transmission. The queues
are always dequed round robin (i.e. strict priority, PFC and ETS are not
supported). This does allow the allocation of a seperate HW queue for low
volume, high priority traffic which will be serviced more promptly.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 82574/82583, there is a hardware bug which might cause a Tx hang when
the internal buffer is full.  Setting this bit enables a hardware fix to
work around the issue.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This code snippet is simply writing default values to the register which is
unnecessary since the values are programmed into the register by default.
There is a special case for 80003es2lan needing the Retransmit on Late
Collision bit set but that is also done in e1000_init_hw_80003es2lan().
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the default hardware values for TIPG except for 80003es2lan(*).  The
code that is removed in this patch is either unnecessarily writing the TIPG
register with the hardware default values for some devices (82571/2/3/4) or
writing the wrong value for others (ICH/PCH LOMs).  The only change in
functionality is setting the correct default TIPG for the latter devices.

(*) The correct value for 80003es2lan is already set properly in
e1000_init_hw_80003es2lan() and e1000_cfg_kmrn_{10_100|1000}_80003es2lan(),
and the unused flag FLAG_TIPG_MEDIUM_FOR_80003ESLAN is removed.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When connected to certain switches, the 82579 PHY might drop link
unexpectedly.  Work around the issue by setting the Mean Square Error
higher than the hardware default.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware erratum workaround where the TXDCTL register must be the same
setting for both queues should always be done.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a patch from Prabhakar Kushwaha <prabhakar@freescale.com>, set
appropriate default interrupt mode dependent on whether CONFIG_PCI_MSI
is enabled in the kernel configuration and if the hardware supports
MSI-X.  Set the module parameter log message accordingly.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make it more like how igb does it, with some additional error checking.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For ring-specific functions, pass a pointer to the ring struct instead of a
pointer to the adapter struct.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Tx/Rx head and tail registers and itr_register are always at known
addresses based on the __iomem address at which the PCI region (from BAR 0)
is mapped and known offsets within the region for each of these registers.
Store and use the full address rather than just the region offset to reduce
unnecessary address calculations.  Also, change current u8 __iomem pointers
to void __iomem pointers.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable RPS by default.  Disallow jumbo frames when both receive checksum
and receive hashing are enabled because the hardware cannot do both IP
payload checksum (enabled when receive checksum is enabled when using
packet split which is used for jumbo frames) and provide RSS hash at the
same time.

v2: added ethtool command to query flow hashing behavior per Ben Hutchings
    and changed the type of rsskey to cleanup the setting of the register
    array and avoid unnecessary casts (as pointed out by Joe Perches).
    The long error messages are not changed since there is nothing in
    the kernel ./Documentation that suggests the preferred method for
    dealing with long messages other than to never break strings; leaving
    them as-is for now.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

1) cleanup whitespace in e1000_rx_checksum() function header comment
2) do not check hardware checksum when Rx checksum is disabled
3) reduce duplicated calls to le16_to_cpu() by just using it within
   e1000_rx_checksum() instead of in each call to the function

v2: use swab16 instead of le16_to_cpu & htons and corrected type for the
passed-in csum
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some WWAN LTE/3G devices based on chipsets from Qualcomm provide
near standard CDC ECM interfaces in addition to the usual serial
interfaces.   The Huawei E392/E398 are examples of such devices.

These typically cannot be fully configured using AT commands
over a serial interface.  It is necessary to speak the proprietary
Qualcomm MSM Interface (QMI) protocol to the device to enable the
ethernet proxy functionality.

The devices embed the QMI protocol in CDC on the control interface,
using standard CDC commands and notifications. The do not otherwise
use CDC commands for the ethernet function.  This driver does
therefore not need access to any other aspects of the control
interface than the descriptors attached to it.

Another driver, cdc-wdm, will provide userspace access to the
QMI protocol independently of this driver.  To facilitate this,
this driver avoids binding to the control interface, and uses
only the associated data interface after parsing the common CDC
functional descriptors on the control interface.

You will want both the cdc-wdm and option drivers as companions to
this driver, to have full access to all interfaces and protocols
exported by the device.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver adds support for Xilinx 10/100/1000 AXI Ethernet.

It can be used, for instance, on Xilinx boards with a Microblaze
architecture like the ML605.

The patch is against the latest net-next tree and checkpatch clean.
Signed-off-by: NAriane Keller <ariane.keller@tik.ee.ethz.ch>
Signed-off-by: NDaniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We introduced a new return here but forgot to drop the lock.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use existing helpers to clarify skb headers manipulation.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using module_platform_driver can make the code smaller.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add polling interface to xen-netfront device to support netconsole

This patch also alters the spin_lock usage to use irqsave variant.
Documentation/networking/netdevices.txt states that start_xmit
can be called with interrupts disabled by netconsole and therefore using
the irqsave/restore locking in this function is looks correct.
Signed-off-by: NTina.Yang <tina.yang@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: NZhenzhong.Duan <zhenzhong.duan@oracle.com>
Tested-by: Ngurudas.pai <gurudas.pai@oracle.com>
[v1: Copy-n-pasted Ian Campbell comments]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>