Most parts of the enable / disable API are no longer used and
can be removed.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Tested-by: NVenkatraman S <svenkatr@ti.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

To prevent I/O as soon as possible at card removal, a new detect work is
re-scheduled without a delay to let a rescan remove the card device as
soon as possible.

Additionally, MMC_CAP2_DETECT_ON_ERR can now be used to handle "slowly"
removed cards that a scheduled detect work did not detect as removed.
To prevent further I/O requests for these lingering removed cards,
check if card has been removed and then schedule a detect work to
properly remove it.
Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Support of PCI mode for the dw_mmc driver. This Patch adds the
support for the scenario where the Synopsys Designware IP
is present on the PCI bus. The patch adds the minimal modifications
necessary for the driver to work on PCI platform. Also added separate
files for PCI and PLATFORM modes of operation.
Signed-off-by: NShashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

MMC-4.5 data tag feature will be used to store the file system meta-data
in the tagged region of eMMC. This will improve the write and subsequent
read transfer time for the meta data.
Signed-off-by: NSaugata Das <saugata.das@linaro.org>
Tested-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Current PIO mode makes a kernel crash with CONFIG_HIGHMEM.
Highmem pages have a NULL from sg_virt(sg).
This patch fixes the following problem.

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP
Modules linked in:
CPU: 0    Not tainted  (3.0.15-01423-gdbf465f #589)
PC is at dw_mci_pull_data32+0x4c/0x9c
LR is at dw_mci_read_data_pio+0x54/0x1f0
pc : [<c0358824>]    lr : [<c035988c>]    psr: 20000193
sp : c0619d48  ip : c0619d70  fp : c0619d6c
r10: 00000000  r9 : 00000002  r8 : 00001000
r7 : 00000200  r6 : 00000000  r5 : e1dd3100  r4 : 00000000
r3 : 65622023  r2 : 0000007f  r1 : eeb96000  r0 : e1dd3100
Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment
xkernel
Control: 10c5387d  Table: 61e2004a  DAC: 00000015
Process swapper (pid: 0, stack limit = 0xc06182f0)
Stack: (0xc0619d48 to 0xc061a000)
9d40:                   e1dd3100 e1a4f000 00000000 e1dd3100 e1a4f000 00000200
9d60: c0619da4 c0619d70 c035988c c03587e4 c0619d9c e18158f4 e1dd3100 e1dd3100
9d80: 00000020 00000000 00000000 00000020 c06e8a84 00000000 c0619e04 c0619da8
9da0: c0359b24 c0359844 e18158f4 e1dd3164 e1dd3168 e1dd3150 3d02fc79 e1dd3154
9dc0: e1dd3178 00000000 00000020 00000000 e1dd3150 00000000 c10dd7e8 e1a84900
9de0: c061e7cc 00000000 00000000 0000008d c06e8a84 c061e780 c0619e4c c0619e08
9e00: c00c4738 c0359a34 3d02fc79 00000000 c0619e4c c05a1698 c05a1670 c05a165c
9e20: c04de8b0 c061e780 c061e7cc e1a84900 ffffed68 0000008d c0618000 00000000
9e40: c0619e6c c0619e50 c00c48b4 c00c46c8 c061e780 c00423ac c061e7cc ffffed68
9e60: c0619e8c c0619e70 c00c7358 c00c487c 0000008d ffffee38 c0618000 ffffed68
9e80: c0619ea4 c0619e90 c00c4258 c00c72b0 c00423ac ffffee38 c0619ecc c0619ea8
9ea0: c004241c c00c4234 ffffffff f8810000 0000006d 00000002 00000001 7fffffff
9ec0: c0619f44 c0619ed0 c0048bc0 c00423c4 220ae7a9 00000000 386f0d30 0005d3a4
9ee0: c00423ac c10dd0b8 c06f2cd8 c0618000 c0594778 c003a674 7fffffff c0619f44
9f00: 386f0d30 c0619f18 c00a6f94 c005be3c 80000013 ffffffff 386f0d30 0005d3a4
9f20: 386f0d30 0005d2d1 c10dd0a8 c10dd0b8 c06f2cd8 c0618000 c0619f74 c0619f48
9f40: c0345858 c005be00 c00a2440 c0618000 c0618000 c00410d8 c06c1944 c00410fc
9f60: c0594778 c003a674 c0619f9c c0619f78 c004a7e8 c03457b4 c0618000 c06c18f8
9f80: 00000000 c0039c70 c06c18d4 c003a674 c0619fb4 c0619fa0 c04ceafc c004a714
9fa0: c06287b4 c06c18f8 c0619ff4 c0619fb8 c0008b68 c04cea68 c0008578 00000000
9fc0: 00000000 c003a674 00000000 10c5387d c0628658 c003aa78 c062f1c4 4000406a
9fe0: 413fc090 00000000 00000000 c0619ff8 40008044 c0008858 00000000 00000000
Backtrace:
[<c03587d8>] (dw_mci_pull_data32+0x0/0x9c) from [<c035988c>] (dw_mci_read_data_pio+0x54/0x1f0)
 r6:00000200 r5:e1a4f000 r4:e1dd3100
 [<c0359838>] (dw_mci_read_data_pio+0x0/0x1f0) from [<c0359b24>] (dw_mci_interrupt+0xfc/0x4a4)
[<c0359a28>] (dw_mci_interrupt+0x0/0x4a4) from [<c00c4738>] (handle_irq_event_percpu+0x7c/0x1b4)
[<c00c46bc>] (handle_irq_event_percpu+0x0/0x1b4) from [<c00c48b4>] (handle_irq_event+0x44/0x64)
[<c00c4870>] (handle_irq_event+0x0/0x64) from [<c00c7358>] (handle_fasteoi_irq+0xb4/0x124)
 r7:ffffed68 r6:c061e7cc r5:c00423ac r4:c061e780
 [<c00c72a4>] (handle_fasteoi_irq+0x0/0x124) from [<c00c4258>] (generic_handle_irq+0x30/0x38)
 r7:ffffed68 r6:c0618000 r5:ffffee38 r4:0000008d
 [<c00c4228>] (generic_handle_irq+0x0/0x38) from [<c004241c>] (asm_do_IRQ+0x64/0xe0)
 r5:ffffee38 r4:c00423ac
 [<c00423b8>] (asm_do_IRQ+0x0/0xe0) from [<c0048bc0>] (__irq_svc+0x80/0x14c)
Exception stack(0xc0619ed0 to 0xc0619f18)
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Modified the mmc_poweroff to resume before sending the poweroff
notification command. In sleep mode only AWAKE and RESET commands are
allowed, so before sending the poweroff notification command resume from
sleep mode and then send the notification command.

PowerOff Notify is tested on a Synopsis Designware Host Controller
(eMMC 4.5). The suspend to RAM and resume works fine.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Tested-by: NGirish K S <girish.shivananjappa@linaro.org>
Reviewed-by: NSaugata Das <saugata.das@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

There is an understood mismatch between the voltage the host controller is
set to and the voltage supplied to the card by a fixed voltage regulator.
Teaching the driver to accept the mismatch is overly complicated.  Instead
just accept the regulator's voltage.

This patch adds MMC_CAP2_BROKEN_VOLTAGE.

If the voltage didn't satisfy between min_uV and max_uV, try to change
the voltage in core.c.  When changing the voltage, maybe use
regulator_set_voltage().

In regulator_set_voltage(), check the below condition.

	/* sanity check */
	if (!rdev->desc->ops->set_voltage &&
	    !rdev->desc->ops->set_voltage_sel) {
		ret = -EINVAL;
		goto out;
	}

If some board should use the fixed-regulator, always return -EINVAL.
Then, eMMC didn't initialize always.

So if use a fixed-regulator, we need to add the MMC_CAP2_BROKEN_VOLTAGE.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Ensure clocks are always enabled before any interaction with the
host controller driver. This makes sure that there is no race
between host execution and the core layer turning off clocks
in different context with clock gating framework.
Signed-off-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NPer Forlin <per.forlin@stericsson.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

module_param(bool) used to counter-intuitively take an int.  In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option.  For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

This patch adds support for the HS200 mode on the host side.
Also enables the tuning feature required when the HS200 mode
is selected.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds the support of the HS200 bus speed for eMMC 4.5 devices.
The eMMC 4.5 devices have support for 200MHz bus speed. The function
prototype of the tuning function is modified to handle the tuning
command number which is different in sd and mmc case.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Host may now use MMC_CAP2_NO_SLEEP_CMD to disable the use
of eMMC sleep/awake command.

This option can be used when your platform has a buggy
kernel crash dump software, which is supposed to store
the dump on the eMMC, but is not able to wake up the eMMC
from sleep state.

In particular, failures have been seen with u-boot; even if
it is fixed there, platforms will be slow to update their
bootloader binaries.
Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: NHanumath Prasad <hanumath.prasad@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Even if a driver provides separate card detection, an interrupt
is still needed to abort mmc requests that are in progress.
SDHCI_QUIRK2_OWN_CARD_DETECTION prevents that, so remove it.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add a means of getting platform data for the SDHCI PCI
devices.  The data is stored against the slot not the
device in order to support multi-slot devices.

The data allows platform-specific setup (such as getting
GPIO numbers from firmware or setting up wl12xx for SDIO)
to be done in platform support files instead of the
sdhci-pci driver.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds a primitive helper to support card hotplug detection on
platforms, where a GPIO, capable of producing interrupts, is used for
detection of card-insertion and -removal events.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

SD/MMC controllers provide different card insertion and removal detection
methods. On some of them the controller itself issues an interrupt, on
others polling is used, on yet others auxiliary means are used for this
purpose, e.g., a GPIO IRQ. Further, on some systems one of those methods
can be chosen at driver probing time and configured in software. E.g., on
some systems the SD/MMC controller card hot-plug detection pin can be
configured either as a respective controller functions, or an IRQ-capable
GPIO. To support such flexible configurations a card hot-plug context
is added by this patch.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds another capabilities field for MMC_CAPS2_XXX.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Enable boot partitions to be read-only locked until next power on via
a sysfs entry. There will be one sysfs entry for each boot partition:

/sys/block/mmcblkXbootY/ro_lock_until_next_power_on

Each boot partition is locked by writing 1 to its file.
Signed-off-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: NJohn Beckett <john.beckett@stericsson.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add a function mmc_detect_card_removed() which upper layers can use to
determine immediately if a card has been removed. This function should
be called after an I/O request fails so that all queued I/O requests
can be errored out immediately instead of waiting for the card device
to be removed.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds support for sdio UHS cards per the version 3.0
spec.

UHS mode is only enabled for version 3.0 cards when both the
host and the controller support UHS modes.

1.8v signaling support is removed if both the card and the
host do not support UHS.  This is done to maintain
compatibility and some system/card combinations break when
1.8v signaling is enabled when the host does not support UHS.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NAaron Lu <Aaron.lu@amd.com>
Reviewed-by: NArindam Nath <arindam.nath@amd.com>
Tested-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Current clock gating framework disables the MCI clock as soon as the
request is completed and enables it when a request arrives. This aggressive
clock gating framework, when enabled, cause following issues:

When there are back-to-back requests from the Queue layer, we unnecessarily
end up disabling and enabling the clocks between these requests since 8MCLK
clock cycles is a very short duration compared to the time delay between
back to back requests reaching the MMC layer. This overhead can effect the
overall performance depending on how long the clock enable and disable
calls take which is platform dependent. For example on some platforms we
can have clock control not on the local processor, but on a different
subsystem and the time taken to perform the clock enable/disable can add
significant overhead.

Also if the host controller driver decides to disable the host clock too
when mmc_set_ios function is called with ios.clock=0, it adds additional
delay and it is highly possible that the next request had already arrived
and unnecessarily blocked in enabling the clocks. This is seen frequently
when the processor is executing at high speeds and in multi-core platforms
thus reduces the overall throughput compared to if clock gating is
disabled.

Fix this by delaying turning off the clocks by posting request on
delayed workqueue. Also cancel the unscheduled pending work, if any,
when there is access to card.

sysfs entry is provided to tune the delay as needed, default
value set to 200ms.
Signed-off-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch is to expose the actual SDCLK frequency in
/sys/kernel/debug/mmcX/ios entry.

For example, if the max clk for a normal speed card is 20MHz this
is reported in /sys/kernel/debug/mmcX/ios.  Unfortunately the actual
SDCLK frequency (i.e. Baseclock / divisor) is not reported at all:
for example, in that case, on Arasan HC, it should be 48/4=12 (MHz).
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add new macros for the high speed 50MHz case, rather than having
a confusing reuse of the value for UHS SDR50, which is 100MHz.
Reported-by: NAaron Lu <aaron.lu@amd.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Adds a quirk that sets the data read timeout to a fixed value instead
of relying on the information in the CSD. The timeout value chosen
is 300ms since that has proven enough for the problematic cards found,
but could be increased if other cards require this.

This patch also enables this quirk for certain Micron cards known to
have this problem.
Signed-off-by: NStefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

'DISK_NAME_LEN' is undeclared when CONFIG_BLOCK is disabled; its use was
introduced via genhd.h by the general purpose partition patch.

To fix, we just add our own MAX_MMC_PART_NAME_LEN macro instead of using
DISK_NAME_LEN.
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NNamjae Jeon <linkinjeon@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Acked-by: NAndrei Warkentin <andreiw@vmware.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Due to hardware bugs, some MMC host controllers don't support
multiple-block reads[1].  To resolve, add a new MMC capability flag,
MMC_CAP2_NO_MULTI_READ, which can be set by affected host controller
drivers.  When this capability is set, all reads will be issued one
sector at a time.

1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read
Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
Revision F (October 2010) (SPRZ278F), available from
http://focus.ti.com/lit/er/sprz278f/sprz278f.pdfSigned-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: NSteve Sakoman <sakoman@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Table 6-2: CCCR bit Definitions, address 00h.  Part E1 SDIO Simplified
Specification Version 3.00, Feb. 25, 2011.

This patch has been tested with Marvell WLAN device SD8797.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

HPI command is defined in eMMC4.41.
This feature is important for eMMC4.5 devices.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds cache feature of eMMC4.5 Spec.
If device supports cache capability, host can utilize some specific
operations.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

MMC v4.5 supports the DISCARD feature (CMD38).  It's different from
trim and there's no check bit.  Currently it's only supported at v4.5.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In the v4.5, there's no secure erase & trim support.
Instead it supports the sanitize feature.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In dw_mmc 2.40a spec, Data register's offset is changed.
Before we used Data register offset 0x100. but if somebody uses a
2.40a controller, we must use 0x200 for Data register.

This patch adds a version-id checking point and uses SDMMC_DATA(x)
instead of SDMMC_DATA.  It assumes 2.40a is the latest version.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).

For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

EXT_CSD[248] includes the default maximum timeout for CMD6.
This field is added at eMMC4.5 Spec. And it can be used for default
timeout except for some operations which don't define the timeout
(i.e. background operation, sanitize, flush cache) in eMMC4.5 Spec.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Ths patch allows runtime PM for sdhci-pci, runtime suspending after
inactivity of 50ms and ensuring runtime resume before SDHC registers
are accessed.  During runtime suspend, interrupts are masked.
The host controller state is restored at runtime resume.

For Medfield, the host controller's card detect mechanism is
supplanted by an always-on GPIO which provides for card detect wake-up.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

It allows gerneral purpose partitions in MMC Device.  And I try to simply
make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei
Warkentin.  After patching, we see general purpose partitions like this:
> cat /proc/partitions
          179 0 847872 mmcblk0
          179 192 4096 mmcblk0gp3
          179 160 4096 mmcblk0gp2
          179 128 4096 mmcblk0gp1
          179 96  1052672 mmcblk0gp0
          179 64  1024 mmcblk0boot1
          179 32  1024 mmcblk0boot0
Signed-off-by: NNamjae Jeon <linkinjeon@gmail.com>
Acked-by: NAndrei Warkentin <awarkentin@vmware.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Intel Medfield platform blocks access to eMMC boot partitions which
results in switch errors.  Since there is no access, mmcboot0/1
devices should not be created.  Add a host capability to reflect that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds the power class selection feature available for mmc
versions 4.0 and above.  During the enumeration stage before switching
to the lower data bus, check if the power class is supported for the
current bus width. If the power class is available then switch to the
power class and use the higher data bus. If power class is not supported
then switch to the lower data bus in a worst case.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Provide platforms with a simplified way to specify MMCIF DMA slave IDs in
a way, similar to SDHI and other sh_dma clients.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

eMMC's may have a hardware reset line.  This patch provides a
host controller operation to implement hardware reset and
a function to reset and reinitialize the card.  Also, for MMC,
the reset is always performed before initialization.

The host must set the new host capability MMC_CAP_HW_RESET
to enable hardware reset.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>