pcim_iomap_regions() conversion missed BAR5.  Fix it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

With STANDBYDOWN tracking added, libata.spindown_compat isn't
necessary anymore.  If userspace shutdown(8) issues STANDBYNOW, libata
warns.  If userspace shutdown(8) doesn't issue STANDBYNOW, libata does
the right thing.  Userspace can tell whether kernel supports spindown
by testing whether sysfs node manage_start_stop exists as before.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As with all other drivers, sata_nv's hpriv is allocated with
devm_kzalloc() and there's no need to free it explicitly.  Kill
nv_remove_one() which incorrectly used kfree() instead of devm_kfree()
and use ata_pci_remove_one() directly.

Original fix is from Peer Chen.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Because nvidia SATA controllers onward base on AHCI, so wildcard in sata_nv
driver is unnecessary.  Also the wildcard sometimes cause sata_nv driver to
be loaded for AHCI controllers,which is not as expected.
Signed-off-by: NPeer Chen <pchen@nvidia.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

After a suspend/resume cycle, the UART may have been reset into
low-speed mode -- either because it's actually been reset, or because
the firmware pokes at the old-style divisor registers. If we detected it
as a NS16550A SuperIO chip in the first place and set baud_base to
921600, then we should do so again in the resume path.

This patch adds that code to serial8250_resume_port(), and also makes
serial8250_resume() actually call serial8250_resume_port() for each port
instead of just calling uart_resume_port() directly. And thus fixes
serial port operation after suspend/resume.

It also fixes a bogus comment where we write the EXCR2 register with a
comment saying /* EXCR1 */
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch add new sub-device-id to support new adapter and changed the
interrupt irq number for unsigned char to unsigned int.

[akpm@osdl.org: fix whitespace in device table]
Signed-off by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make drivers/rtc/Kconfig be clearer about what the various "interfaces"
actually mean, by showing path names.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix typo which breaks build.  How did that happen?
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Refine SCREEN_INFO sanity check for vgacon initialization.

Checking video mode field only to see whenever SCREEN_INFO is
initialized is not enougth, in some cases it is zero although
a vga card is present.  Lets additionally check cols and lines.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Alan <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Strip __cpuinit[data] from Node <-> PXM routines and supporting data
structures.  Also make pxm_to_node_map and node_to_pxm_map local to the
numa acpi module.

This fixes a bug triggered by the following conditions:
- boot on a machine with a SLIT table defined
- kernel is configured w/ CONFIG_HOTPLUG_CPU=n
- cat /sys/devices/system/node/node*/distance
This will cause an oops by calling into a freed memory section.

In particular, on x86_64, __node_distance calls node_to_pxm().
Signed-off-by: NAaron Durbin <adurbin@google.com>
Cc: Len Brown <lenb@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SLAB_CTOR_CONSTRUCTOR is always specified. No point in checking it.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@ucw.cz>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

alpha:

drivers/parport/parport_pc.c: In function 'parport_pc_fifo_write_block_dma':
drivers/parport/parport_pc.c:636: warning: implicit declaration of function 'dma_map_single'
drivers/parport/parport_pc.c:637: error: 'DMA_TO_DEVICE' undeclared (first use in this function)
drivers/parport/parport_pc.c:637: error: (Each undeclared identifier is reported only once
drivers/parport/parport_pc.c:637: error: for each function it appears in.)
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

find_first_zero_bit accepts number of bits, not longs.
Signed-off-by: NDomen Puncer <domen.puncer@telargo.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Our assumption that most distros issue STANDBYNOW seems wrong.  The
upstream sysvinit and thus many distros including gentoo and opensuse
don't take any action for libata disks on spindown.  We can skip
compat handling for these distros so that they don't need to update
anything to take advantage of kernel-side shutdown.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Unlocking ap->lock and ssleeping don't work because SCSI commands can
be issued from completion path without context.  Reimplement delayed
completion by allowing translation functions to override
qc->scsidone(), storing the original completion function to
scmd->scsi_done() and overriding qc->scsidone() with a function which
schedules delayed invocation of scmd->scsi_done().

This isn't pretty at all but all the ugly parts are thankfully
contained in the stop translation path where the compat feature is
implemented.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Whether a controller needs IDE or SATA ACPI hierarchy is determined by
the programming interface of the controller not by whether the
controller is SATA or PATA, or it supports slave device or not.  This
patch adds ATA_FLAG_ACPI_SATA port flags which tells libata-acpi that
the port needs SATA ACPI nodes, and sets the flag for ahci and
sata_sil24.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Device might be resized during ata_dev_configure() due to HPA or
(later) ACPI _GTF.  Currently it's worked around by caching n_sectors
before turning off HPA.  The cached original size is overwritten if
the device is reconfigured without being hardreset - which always
happens after configuring trasnfer mode.  If the device gets hardreset
for some reason after that, revalidation fails with -ENODEV.

This patch makes size checking more robust by moving n_sectors check
from ata_dev_reread_id() to ata_dev_revalidate() after the device is
fully configured.  No matter what happens during configuration, a
device must have the same n_sectors after fully configured to be
treated as the same device.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Separate out ata_dev_reread_id() from ata_dev_revalidate().
ata_dev_reread_id() reads IDENTIFY page and determines whether the
same device is still there.  ata_dev_revalidate() reconfigures after
reread completes.  This will be used by ACPI update.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Hypervisor interfaces need to be negotiated in order to use
some API calls reliably.  So add a small set of interfaces
to request API versions and query current settings.

This allows us to fix some bugs in the hypervisor console:

1) If we can negotiate API group CORE of at least major 1
   minor 1 we can use con_read and con_write which can improve
   console performance quite a bit.

2) When we do a console write request, we should hold the
   spinlock around the whole request, not a byte at a time.
   What would happen is that it's easy for output from
   different cpus to get mixed with each other.

3) Use consistent udelay() based polling, udelay(1) each
   loop with a limit of 1000 polls to handle stuck hypervisor
   console.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

.. because video-buf.c requires PCI, and VIDEO_EM28XX selects it.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NJeff Garzik <jeff@garzik.org>
Acked-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

stuff that does select USB should depend on USB_ARCH_HAS_HCD, or we'll
end up with unbuildable configs.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

need it for page_private(), not all targets have it pulled indirectly
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Not sure how this one got missed in the great purge some time ago but it did.
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_use_dma() duplicates a lot of ide_max_dma_mode() functionality
and as all users of ide_use_dma() were converted to use ide_tune_dma()
now it is possible to add missing checks to ide_tune_dma() and remove
ide_use_dma() completely, so do it.

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Check validity of identify words 62 and 63 before using them in
ide_get_mode_mask().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add the speedproc() method for setting transfer modes, modify config_for_dma()
to call it and use ide_max_dma_mode() to select the best DMA mode.
Add support for the multiword DMA modes 0 and 1, using the upper half of the
'drive_data' field to store the DMA timings to program into the drive control
register when DMA is turned on for real.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* add {cs5530,sc1200}_tunepio() for programming PIO timings

* add {cs5530,sc1200}_tune_chipset() (->speedproc method) for setting
  transfer mode and convert {cs5530,sc1200}_config_dma() to use it

* bump driver version
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

sc1200.c:

* remove open-coded variant of ide_dma_host_off() (== ->dma_host_off),
  it is not needed because ->dma_off_quietly calls ->dma_host_off

* use ->dma_host_on (== ide_dma_host_on() for this driver) instead of
  open-coded variant, call it from the users of sc1200_config_dma2()

  [ there is no need to call ->dma_host_on in sc1200_config_dma() because
    core code takes care of calling ->ide_dma_on on successful execution
    of ->ide_dma_check ]

* add comment about ->tuneproc interface abuse

cs5530.c/sc1200.c:

* core code takes care of calling ->dma_off_quietly before calling
  ->ide_dma_check so there is no need to call it in ->ide_dma_check methods

* bump driver version
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use ide_tune_dma() in ide-cris/it821x/pdc202xx_old/serverworks drivers.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

CS5530/SC1200 specifies that two drives on the same cable cannot mix
UDMA/MDMA.  Add {cs5530,sc1200}_udma_filter() to handle this.  This also
makes it possible to remove open-coded best DMA mode selection and use
standard ide_use_dma()/ide_max_dma_mode() helpers.  While at it bump
version numbers.

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_start_power_step() and set_using_dma() were missing ->dma_off_quietly
call (comment in probe_hwif() states that DMA should be always cleared before
tuning is attempted).  Fix it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* remove code enabling IORDY and prefetch from config_chipset_for_dma(),
  as the comment states it has no real effect because these settings are
  overriden when the PIO mode is set (and for this driver ->autotune == 1
  so PIO mode is always programmed)

* use ide_tune_dma() in pdcnew_config_drive_xfer_rate() and remove no longer
  needed config_chipset_for_dma()

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use ide_tune_dma() in ali15x3_config_drive_for_dma() and remove all the open
coded DMA tuning code and also config_chipset_for_dma().  Set ->atapi_dma flag
correctly in init_hwif_common_ali15x3() so ide_tune_dma() can take care of
checking if ATAPI DMA is allowed and remove open coded ATAPI DMA check from
ali15x3_config_drive_for_dma().

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
  to program PIO5 by config_art_rwp_pio() could result in incorrect PIO
  timings being programmed and possibly the data corruption (for < ATA100
  family chipsets PIO0 timings were used, for ATA100 and ATA100a - the random
  content of test1 variable was used, for ATA133 - MWDMA0 timings were used)

* BUG() in sis5513_tune_chipset() if somebody tries to force unsupported PIO5,
  also cleanup this function a bit while at it

* add comment about PIO0 timings for < ATA100 family chipsets

* remove open-coded best PIO mode selection from config_art_rwp_pio(),
  it contained numerous bugs:

  - it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
    before using them

  - it tried to found out maximum PIO mode basing on minimum IORDY cycle time
    (moreover wrong cycle times were used for PIO1/5)

  - it was overriding PIO blacklist and conservative PIO "downgrade" done
    by ide_get_best_pio_mode()

* use sis5513_tune_drive() instead of config_art_rwp_pio()
  in sis5513_config_xfer_rate() so the correct PIO mode is also set
  on drive even if the device is not IORDY/DMA capable

* config_art_rwp_pio() was always setting the best possible mode and not
  the wanted one - fix it and move ide_get_best_pio_mode() call to
  config_chipset_for_pio()

* don't use ide_find_best_mode() in config_chipset_for_pio(), it was being
  overriden by config_art_rwp_pio() for the host timings anyway + we need to
  set the same PIO mode on the device and the host

* pass correct "pio" argument (255 instead of 5) to sis5513_tune_drive() call
  in sis5513_config_xfer_rate() so the best PIO mode is set on the drive
  and not PIO4

* rename sis5513_tune_drive() to sis5513_tuneproc()
  and config_chipset_for_pio() to sis5513_tune_driver()

* bump driver version
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
  to program PIO5 by svwks_tune_chipset() could result in incorrect PIO
  timings being programmed and possibly the data corruption (it seems that
  the minimum possible values were used but I lack the datasheets to be sure)

* select best PIO mode in svwks_tune_drive() and not in svwks_tune_chipset()
  when doing PIO autotuning (pio == 255)

* don't try to tune PIO in config_chipset_for_dma() as ide_dma_enable() could
  return 1 if DMA was previously enabled (svwks_config_drive_xfer_rate()
  takes care of PIO tuning if no suitable DMA mode is found)

* remove config_chipset_for_pio() and use svwks_tune_drive() instead,
  config_chipset_for_pio() contained numerous bugs when selecting PIO mode
  (luckily it was only used for devices limited to PIO by capabilities/BIOS):

  - it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
    before using them

  - it tried to found out maximum PIO mode basing on minimum IORDY cycle time
    (moreover wrong cycle times were used for PIO0/1/5)

  - it was overriding PIO blacklist and conservative PIO "downgrade" done
    by ide_get_best_pio_mode()

  - if the max drive PIO was PIO5 then XFER_PIO_0/XFER_PIO_SLOW was selected
    (XFER_PIO_SLOW is not supported by svwks_tune_chipset() so the result
     was the same as if using XFER_PIO_5 => wrong PIO timings were set)

  - it was overriding drive->current_speed

* bump driver version
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>