Some Ricoh controllers only respect a full reset when there is no card in the
slot.  As we wait for the reset to complete, we must avoid even requesting
those resets on the buggy controllers.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Sprinkle some mmiowb() where needed (writeX() before unlock()).
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clarify my (Pierre's) position on which GPL versions apply.  The patch only
touches the source files where I am the only major author.  The people who
have made the minor commits to the files have been contacted and have no
issues with this change.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some MMC hosts can only handle log2 block sizes.  Unfortunately,
the MMC password support needs to be able to send non-log2 block
sizes.  Provide a capability so that the MMC password support can
decide whether it should use this support or not.

The unfortunate side effect of this host limitation is that any
MMC card protected by a password which is not a log2 block size
can not be accessed on a host which only allows a log2 block size.

This change just adds the flag.  The MMC password support code
needs updating to use it (if and when it is finally submitted.)
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add a capability flag for drivers to set when they can perform multi-
block transfers to cards _and_ correctly report the number of bytes
transferred should an error occur.

The last point is very important - if a driver reports more bytes than
were actually accepted by the card and an error occurs, there is the
possibility for data loss.

Pierre Ossman provided the patch for wbsd and sdhci.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

O2 Micro's controllers have a larger specification version value and are
therefore denied by the driver. When bypassing this check they seem to work
fine. This patch makes the code a bit more forgiving by changing the error
to a warning.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There was a writel() being used on a 16-bit register.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When there is remaining blocks untransferred, we get two error messages saying
almost the same thing.  Make sure at most one is shown.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Some controllers incorrectly report that the cannot do DMA.  Forcefully enable
it for those that we know it works fine on.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Some controllers fail to complete a reset unless you touch the clock register
first.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

New version number for sdhci driver.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As some specific controllers will have bugs, we need a way to map special
behaviour to certain hardware.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Properly test for controller interface to see if it's DMA capable.  As many
controllers are misconfigured in this regard, also add debug parameters to
force DMA support either way.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The specification states that the capabilities register might need a reset to
get correct values after boot up.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Check the interface version of the controller and bail out if it's an unknown
version.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Conform to the sdhci specification as to which inhibit bits should be checked
at different times.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The controller has an upper limit on the block size. Make sure we do not
cross it.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The sdhci controllers will issue an interrupt when a configurable number of
bytes have been transfered using DMA. The purpose is to handle multiple,
scattered memory pages.

Unfortunately, it requires that all transfers are completely aligned to
memory pages, which we cannot guarantee. So we just disable the function.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The sdhci controllers operate with blocks, not bytes. The PIO routines must
therefore make sure that the minimum unit transfered is a complete block.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The specification says that interrupts should be cleared before the source is
removed.  We should also not set unknown bits.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The sdhci specification states that some registers must be written to in a
specific order.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use the give timeout clock and calculate a proper timeout instead of using the
maximum at all times.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The reset register is automatically cleared when the reset has completed.
Hence, we should busy wait and not have a fixed delay.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The current timeout loop assume that jiffies are updated.  This might not be
the case depending on locks and if the kernel is compiled without preemption.
Change the system to use a counter and fixed delays.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The sdhci controllers can support up to three voltage levels.  Detect which
and report back to the MMC layer.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As sdhci is a generic driver, it is helpful to see some more specific
identification of the actual hardware in dmesg.  PCI vendor, device and
revision is sufficient in most cases.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

A base clock value of 0 means that the driver must get the base clock through
some other means.  As we have no other way of getting it, we must abort.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The MMC specification allows non-power of two block sizes.  As such,
we should not pass the log2 block size to host drivers, but instead
pass the byte size.

However, ARM MMCI can only work with log2 block size, so continue to
pass both the log2 block size and byte block size.  This means that
for the moment, the byte block size must remain a power of two, but
this is the first stage of removing this restriction for other hosts.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On 64-bit machines, we just lost the uppermost 32 bits.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than having every driver duplicate the set_ios debugging,
provide a single version in mmc.c which can be expanded as we
add additional functionality.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than each driver test MMC_DEBUG itself, and define DEBUG,
pass it in via the makefile instead.

Fix drivers to use pr_debug() where appropriate, and avoid defining
a DEBUG() macro.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Driver for the Secure Digital Host Controller Interface specification.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>