Skip to content

K
kernel_linux

OpenHarmony / kernel_linux
上一次同步 4 年多

通知 15
Star 8
Fork 2
K
kernel_linux
切换分支/标签
  1. 05 11月, 2017 2 次提交
  3. 03 11月, 2017 3 次提交
    • C
      bpf: fix verifier NULL pointer dereference · 8c01c4f8
      由 Craig Gallek 提交于 
      do_check() can fail early without allocating env->cur_state under
memory pressure.  Syzkaller found the stack below on the linux-next
tree because of this.

  kasan: CONFIG_KASAN_INLINE enabled
  kasan: GPF could be caused by NULL-ptr deref or user memory access
  general protection fault: 0000 [#1] SMP KASAN
  Dumping ftrace buffer:
     (ftrace buffer empty)
  Modules linked in:
  CPU: 1 PID: 27062 Comm: syz-executor5 Not tainted 4.14.0-rc7+ #106
  Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
  task: ffff8801c2c74700 task.stack: ffff8801c3e28000
  RIP: 0010:free_verifier_state kernel/bpf/verifier.c:347 [inline]
  RIP: 0010:bpf_check+0xcf4/0x19c0 kernel/bpf/verifier.c:4533
  RSP: 0018:ffff8801c3e2f5c8 EFLAGS: 00010202
  RAX: dffffc0000000000 RBX: 00000000fffffff4 RCX: 0000000000000000
  RDX: 0000000000000070 RSI: ffffffff817d5aa9 RDI: 0000000000000380
  RBP: ffff8801c3e2f668 R08: 0000000000000000 R09: 1ffff100387c5d9f
  R10: 00000000218c4e80 R11: ffffffff85b34380 R12: ffff8801c4dc6a28
  R13: 0000000000000000 R14: ffff8801c4dc6a00 R15: ffff8801c4dc6a20
  FS:  00007f311079b700(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00000000004d4a24 CR3: 00000001cbcd0000 CR4: 00000000001406e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   bpf_prog_load+0xcbb/0x18e0 kernel/bpf/syscall.c:1166
   SYSC_bpf kernel/bpf/syscall.c:1690 [inline]
   SyS_bpf+0xae9/0x4620 kernel/bpf/syscall.c:1652
   entry_SYSCALL_64_fastpath+0x1f/0xbe
  RIP: 0033:0x452869
  RSP: 002b:00007f311079abe8 EFLAGS: 00000212 ORIG_RAX: 0000000000000141
  RAX: ffffffffffffffda RBX: 0000000000758020 RCX: 0000000000452869
  RDX: 0000000000000030 RSI: 0000000020168000 RDI: 0000000000000005
  RBP: 00007f311079aa20 R08: 0000000000000000 R09: 0000000000000000
  R10: 0000000000000000 R11: 0000000000000212 R12: 00000000004b7550
  R13: 00007f311079ab58 R14: 00000000004b7560 R15: 0000000000000000
  Code: df 48 c1 ea 03 80 3c 02 00 0f 85 e6 0b 00 00 4d 8b 6e 20 48 b8 00 00 00 00 00 fc ff df 49 8d bd 80 03 00 00 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 b6 0b 00 00 49 8b bd 80 03 00 00 e8 d6 0c 26
  RIP: free_verifier_state kernel/bpf/verifier.c:347 [inline] RSP: ffff8801c3e2f5c8
  RIP: bpf_check+0xcf4/0x19c0 kernel/bpf/verifier.c:4533 RSP: ffff8801c3e2f5c8
  ---[ end trace c8d37f339dc64004 ]---

Fixes: 638f5b90 ("bpf: reduce verifier memory consumption")
Fixes: 1969db47 ("bpf: fix verifier memory leaks")
Signed-off-by: NCraig Gallek <kraig@google.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8c01c4f8
    • A
      bpf: fix out-of-bounds access warning in bpf_check · eba0c929
      由 Arnd Bergmann 提交于 
      The bpf_verifer_ops array is generated dynamically and may be
empty depending on configuration, which then causes an out
of bounds access:

kernel/bpf/verifier.c: In function 'bpf_check':
kernel/bpf/verifier.c:4320:29: error: array subscript is above array bounds [-Werror=array-bounds]

This adds a check to the start of the function as a workaround.
I would assume that the function is never called in that configuration,
so the warning is probably harmless.

Fixes: 00176a34 ("bpf: remove the verifier ops from program structure")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      eba0c929
    • A
      bpf: fix link error without CONFIG_NET · 7cce782e
      由 Arnd Bergmann 提交于 
      I ran into this link error with the latest net-next plus linux-next
trees when networking is disabled:

kernel/bpf/verifier.o:(.rodata+0x2958): undefined reference to `tc_cls_act_analyzer_ops'
kernel/bpf/verifier.o:(.rodata+0x2970): undefined reference to `xdp_analyzer_ops'

It seems that the code was written to deal with varying contents of
the arrray, but the actual #ifdef was missing. Both tc_cls_act_analyzer_ops
and xdp_analyzer_ops are defined in the core networking code, so adding
a check for CONFIG_NET seems appropriate here, and I've verified this with
many randconfig builds

Fixes: 4f9218aa ("bpf: move knowledge about post-translation offsets out of verifier")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7cce782e
  5. 02 11月, 2017 2 次提交
  7. 01 11月, 2017 2 次提交
  9. 22 10月, 2017 2 次提交
  11. 18 10月, 2017 6 次提交
    • J
      bpf: move knowledge about post-translation offsets out of verifier · 4f9218aa
      由 Jakub Kicinski 提交于 
      Use the fact that verifier ops are now separate from program
ops to define a separate set of callbacks for verification of
already translated programs.

Since we expect the analyzer ops to be defined only for
a small subset of all program types initialize their array
by hand (don't use linux/bpf_types.h).
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4f9218aa
    • J
      bpf: remove the verifier ops from program structure · 00176a34
      由 Jakub Kicinski 提交于 
      Since the verifier ops don't have to be associated with
the program for its entire lifetime we can move it to
verifier's struct bpf_verifier_env.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      00176a34
    • J
      bpf: split verifier and program ops · 7de16e3a
      由 Jakub Kicinski 提交于 
      struct bpf_verifier_ops contains both verifier ops and operations
used later during program's lifetime (test_run).  Split the runtime
ops into a different structure.

BPF_PROG_TYPE() will now append ## _prog_ops or ## _verifier_ops
to the names.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7de16e3a
    • J
      bpf: disallow arithmetic operations on context pointer · 28e33f9d
      由 Jakub Kicinski 提交于 
      Commit f1174f77 ("bpf/verifier: rework value tracking")
removed the crafty selection of which pointer types are
allowed to be modified.  This is OK for most pointer types
since adjust_ptr_min_max_vals() will catch operations on
immutable pointers.  One exception is PTR_TO_CTX which is
now allowed to be offseted freely.

The intent of aforementioned commit was to allow context
access via modified registers.  The offset passed to
->is_valid_access() verifier callback has been adjusted
by the value of the variable offset.

What is missing, however, is taking the variable offset
into account when the context register is used.  Or in terms
of the code adding the offset to the value passed to the
->convert_ctx_access() callback.  This leads to the following
eBPF user code:

     r1 += 68
     r0 = *(u32 *)(r1 + 8)
     exit

being translated to this in kernel space:

   0: (07) r1 += 68
   1: (61) r0 = *(u32 *)(r1 +180)
   2: (95) exit

Offset 8 is corresponding to 180 in the kernel, but offset
76 is valid too.  Verifier will "accept" access to offset
68+8=76 but then "convert" access to offset 8 as 180.
Effective access to offset 248 is beyond the kernel context.
(This is a __sk_buff example on a debug-heavy kernel -
packet mark is 8 -> 180, 76 would be data.)

Dereferencing the modified context pointer is not as easy
as dereferencing other types, because we have to translate
the access to reading a field in kernel structures which is
usually at a different offset and often of a different size.
To allow modifying the pointer we would have to make sure
that given eBPF instruction will always access the same
field or the fields accessed are "compatible" in terms of
offset and size...

Disallow dereferencing modified context pointers and add
to selftests the test case described here.

Fixes: f1174f77 ("bpf/verifier: rework value tracking")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      28e33f9d
    • J
      bpf: XDP_REDIRECT enable use of cpumap · 9c270af3
      由 Jesper Dangaard Brouer 提交于 
      This patch connects cpumap to the xdp_do_redirect_map infrastructure.

Still no SKB allocation are done yet.  The XDP frames are transferred
to the other CPU, but they are simply refcnt decremented on the remote
CPU.  This served as a good benchmark for measuring the overhead of
remote refcnt decrement.  If driver page recycle cache is not
efficient then this, exposes a bottleneck in the page allocator.

A shout-out to MST's ptr_ring, which is the secret behind is being so
efficient to transfer memory pointers between CPUs, without constantly
bouncing cache-lines between CPUs.

V3: Handle !CONFIG_BPF_SYSCALL pointed out by kbuild test robot.

V4: Make Generic-XDP aware of cpumap type, but don't allow redirect yet,
 as implementation require a separate upstream discussion.

V5:
 - Fix a maybe-uninitialized pointed out by kbuild test robot.
 - Restrict bpf-prog side access to cpumap, open when use-cases appear
 - Implement cpu_map_enqueue() as a more simple void pointer enqueue

V6:
 - Allow cpumap type for usage in helper bpf_redirect_map,
   general bpf-prog side restriction moved to earlier patch.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9c270af3
    • J
      bpf: introduce new bpf cpu map type BPF_MAP_TYPE_CPUMAP · 6710e112
      由 Jesper Dangaard Brouer 提交于 
      The 'cpumap' is primarily used as a backend map for XDP BPF helper
call bpf_redirect_map() and XDP_REDIRECT action, like 'devmap'.

This patch implement the main part of the map.  It is not connected to
the XDP redirect system yet, and no SKB allocation are done yet.

The main concern in this patch is to ensure the datapath can run
without any locking.  This adds complexity to the setup and tear-down
procedure, which assumptions are extra carefully documented in the
code comments.

V2:
 - make sure array isn't larger than NR_CPUS
 - make sure CPUs added is a valid possible CPU

V3: fix nitpicks from Jakub Kicinski <kubakici@wp.pl>

V5:
 - Restrict map allocation to root / CAP_SYS_ADMIN
 - WARN_ON_ONCE if queue is not empty on tear-down
 - Return -EPERM on memlock limit instead of -ENOMEM
 - Error code in __cpu_map_entry_alloc() also handle ptr_ring_cleanup()
 - Moved cpu_map_enqueue() to next patch

V6: all notice by Daniel Borkmann
 - Fix err return code in cpu_map_alloc() introduced in V5
 - Move cpu_possible() check after max_entries boundary check
 - Forbid usage initially in check_map_func_compatibility()

V7:
 - Fix alloc error path spotted by Daniel Borkmann
 - Did stress test adding+removing CPUs from the map concurrently
 - Fixed refcnt issue on cpu_map_entry, kthread started too soon
 - Make sure packets are flushed during tear-down, involved use of
   rcu_barrier() and kthread_run only exit after queue is empty
 - Fix alloc error path in __cpu_map_entry_alloc() for ptr_ring

V8:
 - Nitpicking comments and gramma by Edward Cree
 - Fix missing semi-colon introduced in V7 due to rebasing
 - Move struct bpf_cpu_map_entry members cpu+map_id to tracepoint patch
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6710e112
  13. 15 10月, 2017 1 次提交
  15. 11 10月, 2017 4 次提交
  17. 08 10月, 2017 2 次提交
    • A
      bpf: fix liveness marking · 8fe2d6cc
      由 Alexei Starovoitov 提交于 
      while processing Rx = Ry instruction the verifier does
regs[insn->dst_reg] = regs[insn->src_reg]
which often clears write mark (when Ry doesn't have it)
that was just set by check_reg_arg(Rx) prior to the assignment.
That causes mark_reg_read() to keep marking Rx in this block as
REG_LIVE_READ (since the logic incorrectly misses that it's
screened by the write) and in many of its parents (until lucky
write into the same Rx or beginning of the program).
That causes is_state_visited() logic to miss many pruning opportunities.

Furthermore mark_reg_read() logic propagates the read mark
for BPF_REG_FP as well (though it's readonly) which causes
harmless but unnecssary work during is_state_visited().
Note that do_propagate_liveness() skips FP correctly,
so do the same in mark_reg_read() as well.
It saves 0.2 seconds for the test below

program               before  after
bpf_lb-DLB_L3.o       2604    2304
bpf_lb-DLB_L4.o       11159   3723
bpf_lb-DUNKNOWN.o     1116    1110
bpf_lxc-DDROP_ALL.o   34566   28004
bpf_lxc-DUNKNOWN.o    53267   39026
bpf_netdev.o          17843   16943
bpf_overlay.o         8672    7929
time                  ~11 sec  ~4 sec

Fixes: dc503a8a ("bpf/verifier: track liveness for pruning")
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NEdward Cree <ecree@solarflare.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8fe2d6cc
    • Y
      bpf: add helper bpf_perf_event_read_value for perf event array map · 908432ca
      由 Yonghong Song 提交于 
      Hardware pmu counters are limited resources. When there are more
pmu based perf events opened than available counters, kernel will
multiplex these events so each event gets certain percentage
(but not 100%) of the pmu time. In case that multiplexing happens,
the number of samples or counter value will not reflect the
case compared to no multiplexing. This makes comparison between
different runs difficult.

Typically, the number of samples or counter value should be
normalized before comparing to other experiments. The typical
normalization is done like:
  normalized_num_samples = num_samples * time_enabled / time_running
  normalized_counter_value = counter_value * time_enabled / time_running
where time_enabled is the time enabled for event and time_running is
the time running for event since last normalization.

This patch adds helper bpf_perf_event_read_value for kprobed based perf
event array map, to read perf counter and enabled/running time.
The enabled/running time is accumulated since the perf event open.
To achieve scaling factor between two bpf invocations, users
can can use cpu_id as the key (which is typical for perf array usage model)
to remember the previous value and do the calculation inside the
bpf program.
Signed-off-by: NYonghong Song <yhs@fb.com>
Acked-by: NAlexei Starovoitov <ast@fb.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      908432ca
  19. 05 10月, 2017 1 次提交
  21. 29 9月, 2017 2 次提交
  23. 27 9月, 2017 1 次提交
    • D
      bpf: add meta pointer for direct access · de8f3a83
      由 Daniel Borkmann 提交于 
      This work enables generic transfer of metadata from XDP into skb. The
basic idea is that we can make use of the fact that the resulting skb
must be linear and already comes with a larger headroom for supporting
bpf_xdp_adjust_head(), which mangles xdp->data. Here, we base our work
on a similar principle and introduce a small helper bpf_xdp_adjust_meta()
for adjusting a new pointer called xdp->data_meta. Thus, the packet has
a flexible and programmable room for meta data, followed by the actual
packet data. struct xdp_buff is therefore laid out that we first point
to data_hard_start, then data_meta directly prepended to data followed
by data_end marking the end of packet. bpf_xdp_adjust_head() takes into
account whether we have meta data already prepended and if so, memmove()s
this along with the given offset provided there's enough room.

xdp->data_meta is optional and programs are not required to use it. The
rationale is that when we process the packet in XDP (e.g. as DoS filter),
we can push further meta data along with it for the XDP_PASS case, and
give the guarantee that a clsact ingress BPF program on the same device
can pick this up for further post-processing. Since we work with skb
there, we can also set skb->mark, skb->priority or other skb meta data
out of BPF, thus having this scratch space generic and programmable
allows for more flexibility than defining a direct 1:1 transfer of
potentially new XDP members into skb (it's also more efficient as we
don't need to initialize/handle each of such new members). The facility
also works together with GRO aggregation. The scratch space at the head
of the packet can be multiple of 4 byte up to 32 byte large. Drivers not
yet supporting xdp->data_meta can simply be set up with xdp->data_meta
as xdp->data + 1 as bpf_xdp_adjust_meta() will detect this and bail out,
such that the subsequent match against xdp->data for later access is
guaranteed to fail.

The verifier treats xdp->data_meta/xdp->data the same way as we treat
xdp->data/xdp->data_end pointer comparisons. The requirement for doing
the compare against xdp->data is that it hasn't been modified from it's
original address we got from ctx access. It may have a range marking
already from prior successful xdp->data/xdp->data_end pointer comparisons
though.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      de8f3a83
  25. 20 9月, 2017 1 次提交
    • D
      bpf: fix ri->map_owner pointer on bpf_prog_realloc · 7c300131
      由 Daniel Borkmann 提交于 
      Commit 109980b8 ("bpf: don't select potentially stale
ri->map from buggy xdp progs") passed the pointer to the prog
itself to be loaded into r4 prior on bpf_redirect_map() helper
call, so that we can store the owner into ri->map_owner out of
the helper.

Issue with that is that the actual address of the prog is still
subject to change when subsequent rewrites occur that require
slow path in bpf_prog_realloc() to alloc more memory, e.g. from
patching inlining helper functions or constant blinding. Thus,
we really need to take prog->aux as the address we're holding,
which also works with prog clones as they share the same aux
object.

Instead of then fetching aux->prog during runtime, which could
potentially incur cache misses due to false sharing, we are
going to just use aux for comparison on the map owner. This
will also keep the patchlet of the same size, and later check
in xdp_map_invalid() only accesses read-only aux pointer from
the prog, it's also in the same cacheline already from prior
access when calling bpf_func.

Fixes: 109980b8 ("bpf: don't select potentially stale ri->map from buggy xdp progs")
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7c300131
  27. 16 9月, 2017 1 次提交
  29. 09 9月, 2017 1 次提交
    • D
      bpf: don't select potentially stale ri->map from buggy xdp progs · 109980b8
      由 Daniel Borkmann 提交于 
      We can potentially run into a couple of issues with the XDP
bpf_redirect_map() helper. The ri->map in the per CPU storage
can become stale in several ways, mostly due to misuse, where
we can then trigger a use after free on the map:

i) prog A is calling bpf_redirect_map(), returning XDP_REDIRECT
and running on a driver not supporting XDP_REDIRECT yet. The
ri->map on that CPU becomes stale when the XDP program is unloaded
on the driver, and a prog B loaded on a different driver which
supports XDP_REDIRECT return code. prog B would have to omit
calling to bpf_redirect_map() and just return XDP_REDIRECT, which
would then access the freed map in xdp_do_redirect() since not
cleared for that CPU.

ii) prog A is calling bpf_redirect_map(), returning a code other
than XDP_REDIRECT. prog A is then detached, which triggers release
of the map. prog B is attached which, similarly as in i), would
just return XDP_REDIRECT without having called bpf_redirect_map()
and thus be accessing the freed map in xdp_do_redirect() since
not cleared for that CPU.

iii) prog A is attached to generic XDP, calling the bpf_redirect_map()
helper and returning XDP_REDIRECT. xdp_do_generic_redirect() is
currently not handling ri->map (will be fixed by Jesper), so it's
not being reset. Later loading a e.g. native prog B which would,
say, call bpf_xdp_redirect() and then returns XDP_REDIRECT would
find in xdp_do_redirect() that a map was set and uses that causing
use after free on map access.

Fix thus needs to avoid accessing stale ri->map pointers, naive
way would be to call a BPF function from drivers that just resets
it to NULL for all XDP return codes but XDP_REDIRECT and including
XDP_REDIRECT for drivers not supporting it yet (and let ri->map
being handled in xdp_do_generic_redirect()). There is a less
intrusive way w/o letting drivers call a reset for each BPF run.

The verifier knows we're calling into bpf_xdp_redirect_map()
helper, so it can do a small insn rewrite transparent to the prog
itself in the sense that it fills R4 with a pointer to the own
bpf_prog. We have that pointer at verification time anyway and
R4 is allowed to be used as per calling convention we scratch
R0 to R5 anyway, so they become inaccessible and program cannot
read them prior to a write. Then, the helper would store the prog
pointer in the current CPUs struct redirect_info. Later in
xdp_do_*_redirect() we check whether the redirect_info's prog
pointer is the same as passed xdp_prog pointer, and if that's
the case then all good, since the prog holds a ref on the map
anyway, so it is always valid at that point in time and must
have a reference count of at least 1. If in the unlikely case
they are not equal, it means we got a stale pointer, so we clear
and bail out right there. Also do reset map and the owning prog
in bpf_xdp_redirect(), so that bpf_xdp_redirect_map() and
bpf_xdp_redirect() won't get mixed up, only the last call should
take precedence. A tc bpf_redirect() doesn't use map anywhere
yet, so no need to clear it there since never accessed in that
layer.

Note that in case the prog is released, and thus the map as
well we're still under RCU read critical section at that time
and have preemption disabled as well. Once we commit with the
__dev_map_insert_ctx() from xdp_do_redirect_map() and set the
map to ri->map_to_flush, we still wait for a xdp_do_flush_map()
to finish in devmap dismantle time once flush_needed bit is set,
so that is fine.

Fixes: 97f91a7c ("bpf: add bpf_redirect_map helper routine")
Reported-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      109980b8
  31. 24 8月, 2017 3 次提交
  33. 20 8月, 2017 1 次提交
  35. 19 8月, 2017 1 次提交
  37. 18 8月, 2017 1 次提交
  39. 17 8月, 2017 2 次提交
    • J
      bpf: add access to sock fields and pkt data from sk_skb programs · 8a31db56
      由 John Fastabend 提交于 
      Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8a31db56
    • J
      bpf: sockmap with sk redirect support · 174a79ff
      由 John Fastabend 提交于 
      Recently we added a new map type called dev map used to forward XDP
packets between ports (6093ec2d). This patches introduces a
similar notion for sockets.

A sockmap allows users to add participating sockets to a map. When
sockets are added to the map enough context is stored with the
map entry to use the entry with a new helper

  bpf_sk_redirect_map(map, key, flags)

This helper (analogous to bpf_redirect_map in XDP) is given the map
and an entry in the map. When called from a sockmap program, discussed
below, the skb will be sent on the socket using skb_send_sock().

With the above we need a bpf program to call the helper from that will
then implement the send logic. The initial site implemented in this
series is the recv_sock hook. For this to work we implemented a map
attach command to add attributes to a map. In sockmap we add two
programs a parse program and a verdict program. The parse program
uses strparser to build messages and pass them to the verdict program.
The parse programs use the normal strparser semantics. The verdict
program is of type SK_SKB.

The verdict program returns a verdict SK_DROP, or  SK_REDIRECT for
now. Additional actions may be added later. When SK_REDIRECT is
returned, expected when bpf program uses bpf_sk_redirect_map(), the
sockmap logic will consult per cpu variables set by the helper routine
and pull the sock entry out of the sock map. This pattern follows the
existing redirect logic in cls and xdp programs.

This gives the flow,

 recv_sock -> str_parser (parse_prog) -> verdict_prog -> skb_send_sock
                                                     \
                                                      -> kfree_skb

As an example use case a message based load balancer may use specific
logic in the verdict program to select the sock to send on.

Sample programs are provided in future patches that hopefully illustrate
the user interfaces. Also selftests are in follow-on patches.
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      174a79ff
  41. 16 8月, 2017 1 次提交
    • E
      bpf/verifier: track liveness for pruning · dc503a8a
      由 Edward Cree 提交于 
      State of a register doesn't matter if it wasn't read in reaching an exit;
 a write screens off all reads downstream of it from all explored_states
 upstream of it.
This allows us to prune many more branches; here are some processed insn
 counts for some Cilium programs:
Program                  before  after
bpf_lb_opt_-DLB_L3.o       6515   3361
bpf_lb_opt_-DLB_L4.o       8976   5176
bpf_lb_opt_-DUNKNOWN.o     2960   1137
bpf_lxc_opt_-DDROP_ALL.o  95412  48537
bpf_lxc_opt_-DUNKNOWN.o  141706  78718
bpf_netdev.o              24251  17995
bpf_overlay.o             10999   9385

The runtime is also improved; here are 'time' results in ms:
Program                  before  after
bpf_lb_opt_-DLB_L3.o         24      6
bpf_lb_opt_-DLB_L4.o         26     11
bpf_lb_opt_-DUNKNOWN.o       11      2
bpf_lxc_opt_-DDROP_ALL.o   1288    139
bpf_lxc_opt_-DUNKNOWN.o    1768    234
bpf_netdev.o                 62     31
bpf_overlay.o                15     13
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      dc503a8a