Add support for the hwmon part of the Fintek F71858FG superio IC to the
f71882fg driver. Many thanks to Jelle de Jong for lending me a motherboard 
with this superio on it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add support for the new incarnation of the Winbond/Nuvoton W83627DHG
chip known as W83627DHG-P. It is basically the same as the original
W83627DHG with an additional automatic can speed control mode (not
supported by the driver yet.)
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NMadhu <madhu.chinakonda@gmail.com>

Documentation for the tmp401 driver.

The documentation describes the tmp401 driver and the supported Texas
Instruments TMP401 and TMP411 temperature sensor chips.

Further documentation for new sysfs attributes supported by this
driver is added to Documentation/hwmon/sysfs-interface.
Signed-off-by: NAndre Prendel <andre.prendel@gmx.de>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Enable auto-probing for the HC10 blade and amend the supported system
list.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add fan_max description.

Add fan limit alarm 'max_alarm' to the alarm section.
Signed-off-by: NChristian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This controller can be found on the D-Link DNS-323 for instance, where
it is to be configured via static i2c_board_info in the board-specific
mach-orion/dns323-setup.c; this driver supports only the new-style
driver model.
Tested-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NHerbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: NMatthew Palmer <mpalmer@debian.org>
Signed-off-by: NLaurie Bradshaw <bradshaw.laurie@googlemail.com>
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add Linux support for the Linear Technology LTC4215 Hot Swap controller
I2C monitoring interface.

I have tested the driver with my board, and it appears to work fine.  With
the power supplies disabled, it reads 11.93V input, 1.93V output, no
current and no power.  With the supplies enabled, it reads 11.93V input,
11.98V output, no current, no power.  I'm not drawing any current at the
moment, so this is reasonable.  The value in the sense register never
reads anything except 0, so I expect to get zero from the current and
power calculations.

I didn't attempt to support changing any of the chip's settings or
enabling the FET.  I'm not sure even how to do that and still fit within
the hwmon framework.  :)
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix english in Documentation, add "how to test" description.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Vladimir Botka <vbotka@suse.cz>
Cc: <Quoc.Pham@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Define a standard interface for the chassis intrusion detection feature
some hardware monitoring chips have. Some drivers have custom sysfs
entries for it, but a standard interface would allow integration with
user-space (namely libsensors.)
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: NMatt Roberds <mattroberds@cox.net>

Directory drivers/i2c/chips is going away, so drivers there must find
new homes. For the pcf8591 driver, the best choice seems to be the
hwmon subsystem. While the Philips PCF8591 device isn't a typical
hardware monitoring chip, its DAC interface is compatible with the
hwmon one, so it fits somewhat.

If a better subsystem is ever created for ADC/DAC chips, the driver
could be moved there.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>

Add initial support for the Nuvoton W83667HG chip to the w83627ehf
driver. It has been tested on ASUS P5QL PRO by Gong Jun.

At the moment there is still a usability issue which is that only in6
or temp3 can be present on the W83667HG, so the driver shouldn't
expose both. This will be addressed later.
Signed-off-by: NGong Jun <JGong@nuvoton.com>
Acked-by: NDavid Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

* The alarms sysfs file is deprecated, and individual alarm files are
  self-explanatory.
* The driver doesn't implement high-reslution temperature readings so
  don't document that.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>

Update documentation to prevent further confusion/duplication.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This adds freefall handling to hp_accel driver.  According to HP, it
should just work, without us having to set the chip up by hand.

hpfall.c is example .c program that parks the disk when accelerometer
detects free fall.  It should work; for now, it uses fixed 20seconds
protection period.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix lis3 documentation to fit into 80 columns.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Hwmon driver for the ADT7475 chip.
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

When I review ocfs2 code, find there are 2 typos to "successfull".  After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)

This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: NColy Li <coyli@suse.de>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NRoland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NDavid Hubbard <david.c.hubbard@gmail.com>

The Texas Instruments TMP121 is a SPI temperature sensor very similar
to the LM70, with slightly higher resolution.  This patch extends the
LM70 driver to support the TMP121.  The TMP123 differs in pin assign-
ment.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This fixes a byteswap bug in the LM70 temperature sensor driver,
which was previously covered up by a converse bug in the driver
for the LM70EVAL-LLP board (which is also fixed).

Other fixes:  doc updates, remove an annoying msleep(), and improve
three-wire protocol handling.
Signed-off-by: NKaiwan N Billimoria <kaiwan@designergraphix.com>
[ dbrownell@users.sourceforge.net: doc and whitespace tweaks ]
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Allow it87.c to handle IT8720 chipset like IT8718 in order to
retrieve voltage, temperatures and fans speed from sensors
tools. Also updating the related documentation.
Signed-off-by: NJean-Marc Spaggiari <jean-marc@spaggiari.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add Linux support for the Linear Technology LTC4245 Multiple Supply Hot
Swap controller I2C monitoring interface.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add some documentation about the f71882fg driver, and update the Kconfig
documentation to report the new supported models.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

It turns out that the adt7470's automatic fan control algorithm only works
when the temperature sensors get updated.  This in turn happens only when
someone tells the chip to read its temperature sensors.  Regrettably, this
means that we have to drive the chip periodically.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- (better, more, bigger ...) then -> (...) than
Signed-off-by: NFrederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

New driver to play with.  As Jean mentioned a couple of years ago, this
chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13
voltage sensors.  This driver has been tested on an IntelliStation Z30.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds a driver to the accelerometer sensor found in several HP
laptops (under the commercial names of "HP Mobile Data Protection System
3D" and "HP 3D driveguard").  It tries to have more or less the same
interfaces as the hdaps and other accelerometer drivers: in sysfs and as
a joystick.

This driver was first written by Yan Burman.  Eric Piel has updated it
and slimed it up (including the removal of an interface to access to the
free-fall feature of the sensor because it is not reliable enough for
now).  Pavel Machek removed few more features and switched locking from
semaphore to mutex.

Several people have contributed to the database of the axes.

[eric.piel@tremplin-utc.net: LIS3LV02D: Conform to the new ACPI API]
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NYan Burman <burman.yan@gmail.com>
Signed-off-by: NPavel Machek <pavel@suse.cz>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>

Add at least the bare minimum of documentation for this chip.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This information was provided in lm-sensors ticket #2350:
http://www.lm-sensors.org/ticket/2350

This is IMHO still not enough to be able to safely implement fan
control support for the AS99127F, but this is valuable information so
I am adding it to the documentation.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add support to set target temperature and tolerance for thermal
cruise mode.
Signed-off-by: NMarc Hulsman <m.hulsman@tudelft.nl>
Acked-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add support for pwm_enable.
Signed-off-by: NMarc Hulsman <m.hulsman@tudelft.nl>
Acked-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add PWM manual control.
Signed-off-by: NMarc Hulsman <m.hulsman@tudelft.nl>
Acked-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.

Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>

Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NHerbert Poetzl <herbert@13thfloor.at>

The lm87 driver normally assumes that firmware configured the chip
correctly.  Since this is not always the case, alllow platform code to
set the channel register value via platform_data.  All other
configuration registers can be changed after driver initialisation.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC.  Adjust the
register conversion functions accordingly.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NMartyn Welch <martyn.welch@gefanuc.com>

Update the links to the datasheet of some of the devices supported by
the lm90 driver. Also remove the links from the driver itself, so that
we don't have to update them twice each time they change.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NMartyn Welch <martyn.welch@gefanuc.com>