VPD register is only used for L1(devid=PCI_DEVICE_ID_ATTANSIC_L1) to
access external NV-memory.
l1c & later chip doesn't use it any more.
PHY 0/1 registers occupy the last 2 slots of the dump table.
Signed-off-by: Nxiong <xiong@qca.qualcomm.com>
Tested-by: NLiu David <dwliu@qca.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the multiple-RX-Q in hardware doesn't work,
all related register definition & code are removed.
Signed-off-by: Nxiong <xiong@qca.qualcomm.com>
Tested-by: NLiu David <dwliu@qca.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the Atheros drivers into drivers/net/ethernet/atheros/ and
make the necessary Kconfig and Makefile changes.

CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: Jie Yang <jie.yang@atheros.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

- unify vlan and nonvlan rx path
- kill adapter->vlgrp and atl1c_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/net/.
This patch removes them.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mechanism used to initiate work events from the interrupt
handler has a classic read/modify/write race between the interrupt
handler that sets the condition, and the worker task that reads and
clears the condition. Close these races by using atomic
bit fields.

Cc: stable@kernel.org
Cc: Jie Yang <jie.yang@atheros.com>
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The up/down are only used in this file.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct net_device has its own struct net_device_stats member, so use
this one instead of a private copy in the atl1c_adapter struct.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add AR8151 v2.0 Gigabit 1000 support
Change jumbo frame size to 6K
Update L0s/L1 rountine
        when link speed is 100M or 1G, set L1 link timer to 4 for l1d_2 and l2c_b2
        set L1 link timer to 7 for l2c_b, set L1 link timer to 0xF for others.
Update atl1c_suspend routine
	just refactory the function, add atl1c_phy_power_saving routine,
	when Wake On Lan enable, this func will be called to save power,
	it will reautoneg PHY to 10/100M speed depend on the link
	partners link capability.
Update atl1c_configure_des_ring
        do not use l2c_b default SRAM configuration.
Signed-off-by: NJie Yang <Jie.Yang@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

AR8151 is a Gigabit Ethernet device. AR8152 devices are
Fast Ethernet devices, there are two revisions, a 1.0
and a 2.0 revision.

This has been tested against these devices:

Driver	Model-name	vendor:device	Type
atl1c 	AR8131		1969:1063	Gigabit Ethernet
atl1c	AR8132		1969:1062	Fast Ethernet
atl1c	AR8151(v1.0)	1969:1073	Gigabit Ethernet
atl1c	AR8152(v1.1)	1969:2060	Fast Ethernet

This device has no hardware available yet so it goes untested,
but it should work:

atl1c	AR8152(v2.0)	1969:2062	Fast Ethernet
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use common_task instead of reset_task and link_chg_task, so it fix "call cancel_work_sync
from the work itself".
Signed-off-by: NJie Yang <jie.yang@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add pci map direction in atl1c_buffer flags, it is used when call pci_unmap
apis.
Signed-off-by: NJie Yang <jie.yang@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

change atl1c_buffer struct, use "u16 flags" instead of "u16 state"
to store more infomation for atl1c_buffer, and restructure clean
atl1c_buffer procedure, add common api atl1c_clean_buffer.
Signed-off-by: NJie Yang <jie.yang@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Parentheses are required or the comparison occurs before the bitand.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove duplicated #include in drivers/net/atl1c/atl1c.h.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Supporting AR8131, and AR8132.
Signed-off-by: NJie Yang <jie.yang@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>