Add DT support to the SCCNCP serial driver.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes "frequency" parameter from SCCNXP platform_data
and uses CLK API for getting clock. If CLK ommited, default IC
frequency will be used instead.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Distinguish usart and uart by read ip name register,
The usart read name is "USAR",
The uart and dbgu read name is "DBGU".
Signed-off-by: NElen Song <elen.song@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

-> The ledptrs[] array is never initialized.
-> There is no place where kbd->ledmode is set to LED_SHOW_MEM therefore the if
   statement does not make much sense.
-> Since LED_SHOW_MEM is not used, it can be removed from the header file as well.
Signed-off-by: NAndreas Platschek <andi.platschek@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These two defines are no longer used.  They were only used by the PCI
serial driver "8250_pci" to support the original ADDI-DATA APCI-7800
card.  In that driver, PCI_VENDOR_ID_ADDIDATA_OLD has been replaced with
PCI_VENDOR_ID_AMCC which has the same value (0x10e8), and
PCI_DEVICE_ID_ADDIDATA_APCI7800 has been replaced with a local #define
PCI_DEVICE_ID_AMCC_ADDIDATA_APCI7800 with the same value (0x818e).
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI_VENDOR_ID_AMCC is defined locally in
"drivers/staging/comedi/comedidev.h" for a few comedi hardware drivers,
namely "adl_pci9118", "addi_apci_1500" and "addi_apci_3120" (also
"addi_apci_1710" but that is not currently built and will probably be
removed soon).  Move the define into "include/linux/pci_ids.h" as it is
shared by several drivers (albeit all comedi drivers currently).

PCI_VENDOR_ID_AMCC happens to have the same value (0x10e8) as
PCI_VENDOR_ID_ADDIDATA_OLD.  The vendor ID is actually assigned to
Applied Micro Circuits Corporation and Addi-Data were using device IDs
assigned by AMCC on some of their earlier PCI boards. The
PCI_VENDOR_ID_ADDIDATA_OLD define is still being used by the "8250_pci"
PCI serial board driver.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support for MAX14830 (advanced quad universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support for MAX3109 (advanced dual universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch rework max310x driver.
Major changes have been made:
- Prepare driver to support ICs with more than one UART.
- Prepare driver to support work with I2C-bus.
The patch changes almost every function and can not be divided into parts.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We attempted to address a regression introduced by commit a57f7f91
(ACPICA: Add Windows8/Server2012 string for _OSI method.) after which
ACPI video backlight support doesn't work on a number of systems,
because the relevant AML methods in the ACPI tables in their BIOSes
become useless after the BIOS has been told that the OS is compatible
with Windows 8.  That problem is tracked by the bug entry at:

https://bugzilla.kernel.org/show_bug.cgi?id=51231

Commit 8c5bd7ad (ACPI / video / i915: No ACPI backlight if firmware
expects Windows 8) introduced for this purpose essentially prevented
the ACPI backlight support from being used if the BIOS had been told
that the OS was compatible with Windows 8 and the i915 driver was
loaded, in which case the backlight would always be handled by i915.
Unfortunately, however, that turned out to cause problems with
backlight to appear on multiple systems with symptoms indicating that
i915 was unable to control the backlight on those systems as
expected.

For this reason, revert commit 8c5bd7ad, but leave the function
acpi_video_backlight_quirks() introduced by it, because another
commit on top of it uses that function.

References: https://lkml.org/lkml/2013/7/21/119
References: https://lkml.org/lkml/2013/7/22/261
References: https://lkml.org/lkml/2013/7/23/429
References: https://lkml.org/lkml/2013/7/23/459
References: https://lkml.org/lkml/2013/7/23/81
References: https://lkml.org/lkml/2013/7/24/27Reported-and-tested-by: NJames Hogan <james@albanarts.com>
Reported-and-tested-by: NKamal Mostafa <kamal@canonical.com>
Reported-and-tested-by: NJörg Otte <jrg.otte@gmail.com>
Reported-and-tested-by: NSteven Newbury <steve@snewbury.org.uk>
Reported-by: NMartin Steigerwald <Martin@lichtvoll.de>
Reported-by: NKalle Valo <kvalo@adurom.com>
Tested-by: NJoerg Platte <jplatte@naasa.net>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Commits 6a1c0680 and
9356b535, respectively
  'tty: Convert termios_mutex to termios_rwsem' and
  'n_tty: Access termios values safely'
introduced a circular lock dependency with console_lock and
termios_rwsem.

The lockdep report [1] shows that n_tty_write() will attempt
to claim console_lock while holding the termios_rwsem, whereas
tty_do_resize() may already hold the console_lock while
claiming the termios_rwsem.

Since n_tty_write() and tty_do_resize() do not contend
over the same data -- the tty->winsize structure -- correct
the lock dependency by introducing a new lock which
specifically serializes access to tty->winsize only.

[1] Lockdep report

======================================================
[ INFO: possible circular locking dependency detected ]
3.10.0-0+tip-xeon+lockdep #0+tip Not tainted
-------------------------------------------------------
modprobe/277 is trying to acquire lock:
 (&tty->termios_rwsem){++++..}, at: [<ffffffff81452656>] tty_do_resize+0x36/0xe0

but task is already holding lock:
 ((fb_notifier_list).rwsem){.+.+.+}, at: [<ffffffff8107aac6>] __blocking_notifier_call_chain+0x56/0xc0

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 ((fb_notifier_list).rwsem){.+.+.+}:
       [<ffffffff810b6d62>] lock_acquire+0x92/0x1f0
       [<ffffffff8175b797>] down_read+0x47/0x5c
       [<ffffffff8107aac6>] __blocking_notifier_call_chain+0x56/0xc0
       [<ffffffff8107ab46>] blocking_notifier_call_chain+0x16/0x20
       [<ffffffff813d7c0b>] fb_notifier_call_chain+0x1b/0x20
       [<ffffffff813d95b2>] register_framebuffer+0x1e2/0x320
       [<ffffffffa01043e1>] drm_fb_helper_initial_config+0x371/0x540 [drm_kms_helper]
       [<ffffffffa01bcb05>] nouveau_fbcon_init+0x105/0x140 [nouveau]
       [<ffffffffa01ad0af>] nouveau_drm_load+0x43f/0x610 [nouveau]
       [<ffffffffa008a79e>] drm_get_pci_dev+0x17e/0x2a0 [drm]
       [<ffffffffa01ad4da>] nouveau_drm_probe+0x25a/0x2a0 [nouveau]
       [<ffffffff813b13db>] local_pci_probe+0x4b/0x80
       [<ffffffff813b1701>] pci_device_probe+0x111/0x120
       [<ffffffff814977eb>] driver_probe_device+0x8b/0x3a0
       [<ffffffff81497bab>] __driver_attach+0xab/0xb0
       [<ffffffff814956ad>] bus_for_each_dev+0x5d/0xa0
       [<ffffffff814971fe>] driver_attach+0x1e/0x20
       [<ffffffff81496cc1>] bus_add_driver+0x111/0x290
       [<ffffffff814982b7>] driver_register+0x77/0x170
       [<ffffffff813b0454>] __pci_register_driver+0x64/0x70
       [<ffffffffa008a9da>] drm_pci_init+0x11a/0x130 [drm]
       [<ffffffffa022a04d>] nouveau_drm_init+0x4d/0x1000 [nouveau]
       [<ffffffff810002ea>] do_one_initcall+0xea/0x1a0
       [<ffffffff810c54cb>] load_module+0x123b/0x1bf0
       [<ffffffff810c5f57>] SyS_init_module+0xd7/0x120
       [<ffffffff817677c2>] system_call_fastpath+0x16/0x1b

-> #1 (console_lock){+.+.+.}:
       [<ffffffff810b6d62>] lock_acquire+0x92/0x1f0
       [<ffffffff810430a7>] console_lock+0x77/0x80
       [<ffffffff8146b2a1>] con_flush_chars+0x31/0x50
       [<ffffffff8145780c>] n_tty_write+0x1ec/0x4d0
       [<ffffffff814541b9>] tty_write+0x159/0x2e0
       [<ffffffff814543f5>] redirected_tty_write+0xb5/0xc0
       [<ffffffff811ab9d5>] vfs_write+0xc5/0x1f0
       [<ffffffff811abec5>] SyS_write+0x55/0xa0
       [<ffffffff817677c2>] system_call_fastpath+0x16/0x1b

-> #0 (&tty->termios_rwsem){++++..}:
       [<ffffffff810b65c3>] __lock_acquire+0x1c43/0x1d30
       [<ffffffff810b6d62>] lock_acquire+0x92/0x1f0
       [<ffffffff8175b724>] down_write+0x44/0x70
       [<ffffffff81452656>] tty_do_resize+0x36/0xe0
       [<ffffffff8146c841>] vc_do_resize+0x3e1/0x4c0
       [<ffffffff8146c99f>] vc_resize+0x1f/0x30
       [<ffffffff813e4535>] fbcon_init+0x385/0x5a0
       [<ffffffff8146a4bc>] visual_init+0xbc/0x120
       [<ffffffff8146cd13>] do_bind_con_driver+0x163/0x320
       [<ffffffff8146cfa1>] do_take_over_console+0x61/0x70
       [<ffffffff813e2b93>] do_fbcon_takeover+0x63/0xc0
       [<ffffffff813e67a5>] fbcon_event_notify+0x715/0x820
       [<ffffffff81762f9d>] notifier_call_chain+0x5d/0x110
       [<ffffffff8107aadc>] __blocking_notifier_call_chain+0x6c/0xc0
       [<ffffffff8107ab46>] blocking_notifier_call_chain+0x16/0x20
       [<ffffffff813d7c0b>] fb_notifier_call_chain+0x1b/0x20
       [<ffffffff813d95b2>] register_framebuffer+0x1e2/0x320
       [<ffffffffa01043e1>] drm_fb_helper_initial_config+0x371/0x540 [drm_kms_helper]
       [<ffffffffa01bcb05>] nouveau_fbcon_init+0x105/0x140 [nouveau]
       [<ffffffffa01ad0af>] nouveau_drm_load+0x43f/0x610 [nouveau]
       [<ffffffffa008a79e>] drm_get_pci_dev+0x17e/0x2a0 [drm]
       [<ffffffffa01ad4da>] nouveau_drm_probe+0x25a/0x2a0 [nouveau]
       [<ffffffff813b13db>] local_pci_probe+0x4b/0x80
       [<ffffffff813b1701>] pci_device_probe+0x111/0x120
       [<ffffffff814977eb>] driver_probe_device+0x8b/0x3a0
       [<ffffffff81497bab>] __driver_attach+0xab/0xb0
       [<ffffffff814956ad>] bus_for_each_dev+0x5d/0xa0
       [<ffffffff814971fe>] driver_attach+0x1e/0x20
       [<ffffffff81496cc1>] bus_add_driver+0x111/0x290
       [<ffffffff814982b7>] driver_register+0x77/0x170
       [<ffffffff813b0454>] __pci_register_driver+0x64/0x70
       [<ffffffffa008a9da>] drm_pci_init+0x11a/0x130 [drm]
       [<ffffffffa022a04d>] nouveau_drm_init+0x4d/0x1000 [nouveau]
       [<ffffffff810002ea>] do_one_initcall+0xea/0x1a0
       [<ffffffff810c54cb>] load_module+0x123b/0x1bf0
       [<ffffffff810c5f57>] SyS_init_module+0xd7/0x120
       [<ffffffff817677c2>] system_call_fastpath+0x16/0x1b

other info that might help us debug this:

Chain exists of:
  &tty->termios_rwsem --> console_lock --> (fb_notifier_list).rwsem

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock((fb_notifier_list).rwsem);
                               lock(console_lock);
                               lock((fb_notifier_list).rwsem);
  lock(&tty->termios_rwsem);

 *** DEADLOCK ***

7 locks held by modprobe/277:
 #0:  (&__lockdep_no_validate__){......}, at: [<ffffffff81497b5b>] __driver_attach+0x5b/0xb0
 #1:  (&__lockdep_no_validate__){......}, at: [<ffffffff81497b69>] __driver_attach+0x69/0xb0
 #2:  (drm_global_mutex){+.+.+.}, at: [<ffffffffa008a6dd>] drm_get_pci_dev+0xbd/0x2a0 [drm]
 #3:  (registration_lock){+.+.+.}, at: [<ffffffff813d93f5>] register_framebuffer+0x25/0x320
 #4:  (&fb_info->lock){+.+.+.}, at: [<ffffffff813d8116>] lock_fb_info+0x26/0x60
 #5:  (console_lock){+.+.+.}, at: [<ffffffff813d95a4>] register_framebuffer+0x1d4/0x320
 #6:  ((fb_notifier_list).rwsem){.+.+.+}, at: [<ffffffff8107aac6>] __blocking_notifier_call_chain+0x56/0xc0

stack backtrace:
CPU: 0 PID: 277 Comm: modprobe Not tainted 3.10.0-0+tip-xeon+lockdep #0+tip
Hardware name: Dell Inc. Precision WorkStation T5400  /0RW203, BIOS A11 04/30/2012
 ffffffff8213e5e0 ffff8802aa2fb298 ffffffff81755f19 ffff8802aa2fb2e8
 ffffffff8174f506 ffff8802aa2fa000 ffff8802aa2fb378 ffff8802aa2ea8e8
 ffff8802aa2ea910 ffff8802aa2ea8e8 0000000000000006 0000000000000007
Call Trace:
 [<ffffffff81755f19>] dump_stack+0x19/0x1b
 [<ffffffff8174f506>] print_circular_bug+0x1fb/0x20c
 [<ffffffff810b65c3>] __lock_acquire+0x1c43/0x1d30
 [<ffffffff810b775e>] ? mark_held_locks+0xae/0x120
 [<ffffffff810b78d5>] ? trace_hardirqs_on_caller+0x105/0x1d0
 [<ffffffff810b6d62>] lock_acquire+0x92/0x1f0
 [<ffffffff81452656>] ? tty_do_resize+0x36/0xe0
 [<ffffffff8175b724>] down_write+0x44/0x70
 [<ffffffff81452656>] ? tty_do_resize+0x36/0xe0
 [<ffffffff81452656>] tty_do_resize+0x36/0xe0
 [<ffffffff8146c841>] vc_do_resize+0x3e1/0x4c0
 [<ffffffff8146c99f>] vc_resize+0x1f/0x30
 [<ffffffff813e4535>] fbcon_init+0x385/0x5a0
 [<ffffffff8146a4bc>] visual_init+0xbc/0x120
 [<ffffffff8146cd13>] do_bind_con_driver+0x163/0x320
 [<ffffffff8146cfa1>] do_take_over_console+0x61/0x70
 [<ffffffff813e2b93>] do_fbcon_takeover+0x63/0xc0
 [<ffffffff813e67a5>] fbcon_event_notify+0x715/0x820
 [<ffffffff81762f9d>] notifier_call_chain+0x5d/0x110
 [<ffffffff8107aadc>] __blocking_notifier_call_chain+0x6c/0xc0
 [<ffffffff8107ab46>] blocking_notifier_call_chain+0x16/0x20
 [<ffffffff813d7c0b>] fb_notifier_call_chain+0x1b/0x20
 [<ffffffff813d95b2>] register_framebuffer+0x1e2/0x320
 [<ffffffffa01043e1>] drm_fb_helper_initial_config+0x371/0x540 [drm_kms_helper]
 [<ffffffff8173cbcb>] ? kmemleak_alloc+0x5b/0xc0
 [<ffffffff81198874>] ? kmem_cache_alloc_trace+0x104/0x290
 [<ffffffffa01035e1>] ? drm_fb_helper_single_add_all_connectors+0x81/0xf0 [drm_kms_helper]
 [<ffffffffa01bcb05>] nouveau_fbcon_init+0x105/0x140 [nouveau]
 [<ffffffffa01ad0af>] nouveau_drm_load+0x43f/0x610 [nouveau]
 [<ffffffffa008a79e>] drm_get_pci_dev+0x17e/0x2a0 [drm]
 [<ffffffffa01ad4da>] nouveau_drm_probe+0x25a/0x2a0 [nouveau]
 [<ffffffff8175f162>] ? _raw_spin_unlock_irqrestore+0x42/0x80
 [<ffffffff813b13db>] local_pci_probe+0x4b/0x80
 [<ffffffff813b1701>] pci_device_probe+0x111/0x120
 [<ffffffff814977eb>] driver_probe_device+0x8b/0x3a0
 [<ffffffff81497bab>] __driver_attach+0xab/0xb0
 [<ffffffff81497b00>] ? driver_probe_device+0x3a0/0x3a0
 [<ffffffff814956ad>] bus_for_each_dev+0x5d/0xa0
 [<ffffffff814971fe>] driver_attach+0x1e/0x20
 [<ffffffff81496cc1>] bus_add_driver+0x111/0x290
 [<ffffffffa022a000>] ? 0xffffffffa0229fff
 [<ffffffff814982b7>] driver_register+0x77/0x170
 [<ffffffffa022a000>] ? 0xffffffffa0229fff
 [<ffffffff813b0454>] __pci_register_driver+0x64/0x70
 [<ffffffffa008a9da>] drm_pci_init+0x11a/0x130 [drm]
 [<ffffffffa022a000>] ? 0xffffffffa0229fff
 [<ffffffffa022a000>] ? 0xffffffffa0229fff
 [<ffffffffa022a04d>] nouveau_drm_init+0x4d/0x1000 [nouveau]
 [<ffffffff810002ea>] do_one_initcall+0xea/0x1a0
 [<ffffffff810c54cb>] load_module+0x123b/0x1bf0
 [<ffffffff81399a50>] ? ddebug_proc_open+0xb0/0xb0
 [<ffffffff813855ae>] ? trace_hardirqs_on_thunk+0x3a/0x3f
 [<ffffffff810c5f57>] SyS_init_module+0xd7/0x120
 [<ffffffff817677c2>] system_call_fastpath+0x16/0x1b
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace the SATA_PHY_# by the more readable definitons.

tj: Being routed through libata branch to enable implementation of
    ahci_imx.
Signed-off-by: NRichard Zhu <r65037@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

This reverts commits
    67822649
    39761214
    0b95a7f8
    31d93962
    2d31e518

Unfortunately this change broke boot on some systems that used an
initrd which does not include the newly created crct10dif modules.
As these modules are required by sd_mod under certain configurations
this is a serious problem.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

In canonical mode, an EOF which is not the first character of the line
causes read() to complete and return the number of characters read so
far (commonly referred to as EOF push). However, if the previous read()
returned because the user buffer was full _and_ the next character
is an EOF not at the beginning of the line, read() must not return 0,
thus mistakenly indicating the end-of-file condition.

The TTY_PUSH flag is used to indicate an EOF was received which is not
at the beginning of the line. Because the EOF push condition is
evaluated by a thread other than the read(), multiple EOF pushes can
cause a premature end-of-file to be indicated.

Instead, discover the 'EOF push as first read character' condition
from the read() thread itself, and restart the i/o loop if detected.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

TTY_BUFFER_PAGE is only used within drivers/tty/tty_buffer.c;
relocate to that file scope.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert the tty_buffer_flush() exclusion mechanism to a
public interface - tty_buffer_lock/unlock_exclusive() - and use
the interface to safely write the paste selection to the line
discipline.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Atomic bit ops are no longer required to indicate a flip buffer
flush is pending, as the flush_mutex is sufficient barrier.

Remove the unnecessary port .iflags field and localize flip buffer
state to struct tty_bufhead.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Separate the head and tail ptrs to avoid cache-line contention
(so called 'false-sharing') between concurrent threads.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that dropping the buffer lock is not necessary (as result of
converting the spin lock to a mutex), the flip buffer flush no
longer needs to be handled by the buffer work.

Simply signal a flush is required; the buffer work will exit the
i/o loop, which allows tty_buffer_flush() to proceed.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The buffer work may race with parallel tty_buffer_flush. Use a
mutex to guarantee exclusive modify access to the head flip
buffer.

Remove the unneeded spin lock.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Lockless flip buffers require atomically updating the bytes-in-use
watermark.

The pty driver also peeks at the watermark value to limit
memory consumption to a much lower value than the default; query
the watermark with new fn, tty_buffer_space_avail().
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use a 0-sized sentinel to avoid assigning the head ptr from
the driver side thread. This also eliminates testing head/tail
for NULL.

When the sentinel is first 'consumed' by the buffer work
(or by tty_buffer_flush()), it is detached from the list but not
freed nor added to the free list. Both buffer work and
tty_buffer_flush() continue to preserve at least 1 flip buffer
to which head & tail is pointed.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation for lockless flip buffers, make the flip buffer
free list lockless.

NB: using llist is not the optimal solution, as the driver and
buffer work may contend over the llist head unnecessarily. However,
test measurements indicate this contention is low.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The char_buf_ptr and flag_buf_ptr values are trivially derived from
the .data field offset; compute values as needed.

Fixes a long-standing type-mismatch with the char and flag ptrs.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

No tty driver modifies termios during throttle() or unthrottle().
Therefore, only read safety is required.

However, tty_throttle_safe and tty_unthrottle_safe must still be
mutually exclusive; introduce throttle_mutex for that purpose.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

termios is commonly accessed unsafely (especially by N_TTY)
because the existing mutex forces exclusive access.
Convert existing usage.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Although line discipline receiving is single-producer/single-consumer,
using tty->receive_room to manage flow control creates unnecessary
critical regions requiring additional lock use.

Instead, introduce the optional .receive_buf2() ldisc method which
returns the # of bytes actually received. Serialization is guaranteed
by the caller.

In turn, the line discipline should schedule the buffer work item
whenever space becomes available; ie., when there is room to receive
data and receive_room() previously returned 0 (the buffer work
item stops processing if receive_buf2() returns 0). Note the
'no room' state need not be atomic despite concurrent use by two
threads because only the buffer work thread can set the state and
only the read() thread can clear the state.

Add n_tty_receive_buf2() as the receive_buf2() method for N_TTY.
Provide a public helper function, tty_ldisc_receive_buf(), to use
when directly accessing the receive_buf() methods.

Line disciplines not using input flow control can continue to set
tty->receive_room to a fixed value and only provide the receive_buf()
method.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Line discipline locking was performed with a combination of
a mutex, a status bit, a count, and a waitqueue -- basically,
a rw semaphore.

Replace the existing combination with an ld_semaphore.

Fixes:
 1) the 'reference acquire after ldisc locked' bug
 2) the over-complicated halt mechanism
 3) lock order wrt. tty_lock()
 4) dropping locks while changing ldisc
 5) previously unidentified deadlock while locking ldisc from
    both linked ttys concurrently
 6) previously unidentified recursive deadlocks

Adds much-needed lockdep diagnostics.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the following:

BUG: key ffff88043bdd0330 not in .data!
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:2987 lockdep_init_map+0x565/0x5a0()
DEBUG_LOCKS_WARN_ON(1)
Modules linked in: glue_helper sb_edac(+) edac_core snd acpi_cpufreq lrw gf128mul ablk_helper iTCO_wdt evdev i2c_i801 dcdbas button cryptd pcspkr iTCO_vendor_support usb_common lpc_ich mfd_core soundcore mperf processor microcode
CPU: 2 PID: 599 Comm: modprobe Not tainted 3.10.0 #1
Hardware name: Dell Inc. Precision T3600/0PTTT9, BIOS A08 01/24/2013
 0000000000000009 ffff880439a1d920 ffffffff8160a9a9 ffff880439a1d958
 ffffffff8103d9e0 ffff88043af4a510 ffffffff81a16e11 0000000000000000
 ffff88043bdd0330 0000000000000000 ffff880439a1d9b8 ffffffff8103dacc
Call Trace:
  dump_stack
  warn_slowpath_common
  warn_slowpath_fmt
  lockdep_init_map
  ? trace_hardirqs_on_caller
  ? trace_hardirqs_on
  debug_mutex_init
  __mutex_init
  bus_register
  edac_create_sysfs_mci_device
  edac_mc_add_mc
  sbridge_probe
  pci_device_probe
  driver_probe_device
  __driver_attach
  ? driver_probe_device
  bus_for_each_dev
  driver_attach
  bus_add_driver
  driver_register
  __pci_register_driver
  ? 0xffffffffa0010fff
  sbridge_init
  ? 0xffffffffa0010fff
  do_one_initcall
  load_module
  ? unset_module_init_ro_nx
  SyS_init_module
  tracesys
---[ end trace d24a70b0d3ddf733 ]---
EDAC MC0: Giving out device to 'sbridge_edac.c' 'Sandy Bridge Socket#0': DEV 0000:3f:0e.0
EDAC sbridge: Driver loaded.

What happens is that bus_register needs a statically allocated lock_key
because the last is handed in to lockdep. However, struct mem_ctl_info
embeds struct bus_type (the whole struct, not a pointer to it) and the
whole thing gets dynamically allocated.

Fix this by using a statically allocated struct bus_type for the MC bus.
Signed-off-by: NBorislav Petkov <bp@suse.de>
Acked-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: stable@kernel.org # v3.10
Signed-off-by: NTony Luck <tony.luck@intel.com>

The em_x270_mci_setpower() and em_x270_usb_hub_init() functions
call regulator_enable(), which may return an error that must
be checked.

This changes the em_x270_usb_hub_init() function to bail out
if it fails, and changes the pxamci_platform_data->setpower
callback so that the a failed em_x270_mci_setpower call
can be propagated by the pxamci driver into the mmc core.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: NChris Ball <cjb@laptop.org>
[olof: fixed order of regulator_enable() and test in em_x270_usb_hub_init]
Signed-off-by: NOlof Johansson <olof@lixom.net>

On platforms with no support for the shdma dmaengine driver build is
currently failing with

drivers/built-in.o: In function `sh_mobile_sdhi_probe':
drivers/mmc/host/sh_mobile_sdhi.c:170: undefined reference to`shdma_chan_filter'

Fix the breakage by defining shdma_chan_filter to NULL in such
configurations.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
[horms+renesas@verge.net.au: Apply change to shdma-base.h instead of sh_dma.h]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NOlof Johansson <olof@lixom.net>

so that it can be used in places like d_compare/d_hash
without causing a compiler warning.
Signed-off-by: NPeng Tao <tao.peng@emc.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

In commit 48cc32d3
("vlan: don't deliver frames for unknown vlans to protocols")
Florian made sure we set pkt_type to PACKET_OTHERHOST
if the vlan id is set and we could find a vlan device for this
particular id.

But we also have a problem if prio bits are set.

Steinar reported an issue on a router receiving IPv6 frames with a
vlan tag of 4000 (id 0, prio 2), and tunneled into a sit device,
because skb->vlan_tci is set.

Forwarded frame is completely corrupted : We can see (8100:4000)
being inserted in the middle of IPv6 source address :

16:48:00.780413 IP6 2001:16d8:8100:4000:ee1c:0:9d9:bc87 >
9f94:4d95:2001:67c:29f4::: ICMP6, unknown icmp6 type (0), length 64
       0x0000:  0000 0029 8000 c7c3 7103 0001 a0ae e651
       0x0010:  0000 0000 ccce 0b00 0000 0000 1011 1213
       0x0020:  1415 1617 1819 1a1b 1c1d 1e1f 2021 2223
       0x0030:  2425 2627 2829 2a2b 2c2d 2e2f 3031 3233

It seems we are not really ready to properly cope with this right now.

We can probably do better in future kernels :
vlan_get_ingress_priority() should be a netdev property instead of
a per vlan_dev one.

For stable kernels, lets clear vlan_tci to fix the bugs.
Reported-by: NSteinar H. Gunderson <sesse@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to Matthew Garrett, "Windows 8 leaves backlight control up
to individual graphics drivers rather than making ACPI calls itself.
There's plenty of evidence to suggest that the Intel driver for
Windows [8] doesn't use the ACPI interface, including the fact that
it's broken on a bunch of machines when the OS claims to support
Windows 8.  The simplest thing to do appears to be to disable the
ACPI backlight interface on these systems".

There's a problem with that approach, however, because simply
avoiding to register the ACPI backlight interface if the firmware
calls _OSI for Windows 8 may not work in the following situations:
 (1) The ACPI backlight interface actually works on the given system
     and the i915 driver is not loaded (e.g. another graphics driver
     is used).
 (2) The ACPI backlight interface doesn't work on the given system,
     but there is a vendor platform driver that will register its
     own, equally broken, backlight interface if not prevented from
     doing so by the ACPI subsystem.
Therefore we need to allow the ACPI backlight interface to be
registered until the i915 driver is loaded which then will unregister
it if the firmware has called _OSI for Windows 8 (or will register
the ACPI video driver without backlight support if not already
present).

For this reason, introduce an alternative function for registering
ACPI video, acpi_video_register_with_quirks(), that will check
whether or not the ACPI video driver has already been registered
and whether or not the backlight Windows 8 quirk has to be applied.
If the quirk has to be applied, it will block the ACPI backlight
support and either unregister the backlight interface if the ACPI
video driver has already been registered, or register the ACPI
video driver without the backlight interface otherwise.  Make
the i915 driver use acpi_video_register_with_quirks() instead of
acpi_video_register() in i915_driver_load().

This change is based on earlier patches from Matthew Garrett,
Chun-Yi Lee and Seth Forshee and includes a fix from Aaron Lu's.

References: https://bugzilla.kernel.org/show_bug.cgi?id=51231Tested-by: NAaron Lu <aaron.lu@intel.com>
Tested-by: NIgor Gnatenko <i.gnatenko.brain@gmail.com>
Tested-by: NYves-Alexis Perez <corsac@debian.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: NAaron Lu <aaron.lu@intel.com>
Acked-by: NMatthew Garrett <matthew.garrett@nebula.com>

__list_for_each used to be the non prefetch() aware list walking
primitive.  When we removed the prefetch macros from the list routines,
it became redundant.  Given it does exactly the same thing as
list_for_each now, we might as well remove it and call list_for_each
directly.

All users of __list_for_each have been converted to list_for_each calls
in the current merge window.
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The USB_MAXCHILDREN symbol is used in include/uapi/linux/usb/ch11.h, a
user-mode header, even though it is defined in include/linux/usb.h,
which is kernel-only.  This causes compile-time errors when user
programs try to #include linux/usb/ch11.h.

This patch fixes the problem by moving the definition of USB_MAXCHILDREN
into ch11.h.  It also gets rid of unneeded parentheses.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

With the last patches stat.h was included to the header, and thus those
permission defines should be used.
Signed-off-by: NOliver Schinagl <oliver@schinagl.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

With the recent changes to sysfs there's various helper macro's.
However there's no RW, RO BIN_ helper macro's. This patch adds them.
Signed-off-by: NOliver Schinagl <oliver@schinagl.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We should be using groups, not attribute lists, for classes to allow
subdirectories, and soon, binary files.  Groups are just more flexible
overall, so add them.

The dev_attrs list will go away after all in-kernel users are converted
to use dev_groups.
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

device_create_groups lets callers create devices as well as associated
sysfs attributes with a single call. This avoids race conditions seen
if sysfs attributes on new devices are created later.

[fixed up comment block placement and add checks for printk buffer
formats - gregkh]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>