core-transaction.c transmit_complete_callback() and close_transaction()
expect packet callback status to be an ACK or RCODE, and ACKs get
translated to RCODEs for transaction callbacks.

An old comment on the packet callback API (been there from the initial
submission of the stack) and the dummy_driver implementation of
send_request/send_response deviated from this as they also included
-ERRNO in the range of status values.

Let's narrow status values down to ACK and RCODE to prevent surprises.
RCODE_CANCELLED is chosen as the dummy_driver's RCODE as its meaning of
"transaction timed out" comes closest to what happens when a transaction
coincides with card removal.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Bus resets which are triggered
  - by the kernel drivers after updates of the local nodes' config ROM,
  - by userspace software via ioctl
shall be deferred until after >=2 seconds after the last bus reset.

If multiple modifications of the local nodes' config ROM happen in a row,
only a single bus reset should happen after them.

When the local node's link goes from inactive to active or vice versa,
and at the two occasions of bus resets mentioned above --- and if the
current gap count differs from 63 --- the bus reset should be preceded
by a PHY configuration packet that reaffirms the gap count.  Otherwise a
bus manager would have to reset the bus again right after that.

This is necessary to promote bus stability, e.g. leave grace periods for
allocations and reallocations of isochronous channels and bandwidth,
SBP-2 reconnections etc.; see IEEE 1394 clause 8.2.1.

This change implements all of the above by moving bus reset initiation
into a delayed work (except for bus resets which are triggered by the
bus manager workqueue job and are performed there immediately).  It
comes with a necessary addition to the card driver methods that allows
to get the current gap count from PHY registers.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Fix an obscure ABI feature that is a bit of a hassle to implement.
However, somebody put it into the ABI, so let's fill in a sensible
value there.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

void (*fw_address_callback_t)(..., int speed, ...) is the speed that a
remote node chose to transmit a request to us.  In case of split
transactions, firewire-core will transmit the response at that speed.

Upper layer drivers on the other hand (firewire-net, -sbp2, firedtv, and
userspace drivers) cannot do anything useful with that speed datum,
except log it for debug purposes.  But data that is merely potentially
(not even actually) used for debug purposes does not belong into the API.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Push the maintenance of STATE_CLEAR/SET.abdicate down into the card
driver.  This way, the read/write_csr_reg driver method works uniformly
across all CSR offsets.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

by feature variables in the fw_card struct.  The hook appeared to be an
unnecessary abstraction in the card driver interface.

Cleaner would be to pass those feature flags as arguments to
fw_card_initialize() or fw_card_add(), but the FairnessControl register
is in the SCLK domain and may therefore not be accessible while Link
Power Status is off, i.e. before the card->driver->enable call from
fw_card_add().
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Implement the abdicate bit, which is required for bus manager
capable nodes and tested by the Base 1394 Test Suite.

Finally, something to do at a command reset!  :-)
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Implement the MAIN_UTILITY register, which is utterly optional
but useful as a safe target for diagnostic read/write/broadcast
transactions.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

If supported by the OHCI controller, implement the PRIORITY_BUDGET
register, which is required for nodes that can use asynchronous
priority arbitration.

To allow the core to determine what features the lowlevel device
supports, add a new card driver callback.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Implement the SPLIT_TIMEOUT registers.  Besides being required by the
spec, this is desirable for some IIDC devices and necessary for many
audio devices to be able to increase the timeout from userspace.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Using a single timeout for all transaction that need to be flushed does
not work if the submission of new transactions can defer the timeout
indefinitely into the future.  We need to have timeouts that do not
change due to other transactions; the simplest way to do this is with a
separate timer for each transaction.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (+ one lockdep annotation)

Clemens Ladisch pointed out that
  - BIB_IMC is not named like the field is called in the standard,
  - readers of the code may get worried about the magic 0x0c0083c0,
  - a CSR_NODE_CAPABILITIES key is there in the header but not put to
    good use.

So let's rename BIB_IMC, add a defined constant for Node_Capabilities
and a comment which reassures people that somebody thought about it and
they don't have to (or if they still do, tell them where they have to
look for confirmation), and prune our incomplete and arbitrary set of
defined constants of CSR key IDs.  And there is a nother magic number,
that of Bus_Information_Block.Bus_Name, to be defined and commented.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Several config ROM related functions only peek at the ROM cache; mark
their arguments as const pointers.  Ditto fw_device.config_rom and
fw_unit.directory, as the memory behind them is meant to be write-once.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Witespace and comment changes, and a different way to say i + 1 < end.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The core (sysfs attributes), the firedtv driver, and possible future
drivers all read strings from some configuration ROM directory.  Factor
out the generic code from show_text_leaf() into a new helper function,
modified slightly to handle arbitrary buffer sizes.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Control of more than one AV/C device at once --- e.g. camcorders, tape
decks, audio devices, TV tuners --- failed or worked only unreliably,
depending on driver implementation.  This affected kernelspace and
userspace drivers alike and was caused by firewire-core's inability to
accept multiple registrations of FCP listeners.

The fix allows multiple address handlers to be registered for the FCP
command and response registers.  When a request for these registers is
received, all handlers are invoked, and the Firewire response is
generated by the core and not by any handler.

The cdev API does not change, i.e., userspace is still expected to send
a response for FCP requests; this response is silently ignored.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (changelog, rebased, whitespace)

I was told that there are obscure architectures with non-coherent DMA
which may DMA-map to bus address 0.  We shall not use 0 as a magic
number of uninitialized bus address variables.

The packet->payload_length > 0 test cannot be used either (except in
at_context_queue_packet) because local requests are not DMA-mapped
regardless of payload_length.  Hence add a state flag to struct
fw_packet.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The Topology Map of the local node was created in CPU byte order,
then a temporary big endian copy was created to compute the CRC,
and when a read request to the Topology Map arrived it had to be
converted to big endian byte order again.

We now generate it in big endian byte order in the first place.
This also rids us of 1000 bytes stack usage in tasklet context.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The config ROM image of the local node was created in CPU byte order,
then a temporary big endian copy was created to compute the CRC, and
finally the card driver created its own big endian copy.

We now generate it in big endian byte order in the first place to avoid
one byte order conversion and the temporary on-stack copy of the ROM
image (1000 bytes stack usage in process context).  Furthermore, two
1000 bytes memset()s are replaced by one 1000 bytes - ROM length sized
memset.

The trivial fw_memcpy_{from,to}_be32() helpers are now superfluous and
removed.  The newly added __compute_block_crc() function will be folded
into fw_compute_block_crc() in a subsequent change.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

fw_card_get, fw_card_put, fw_card_release are currently not exported for
use outside the firewire-core.  Move their definitions/ declarations
from the subsystem header file to the core header file.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The DMA mapping API cannot map on-stack addresses, as explained in
Documentation/DMA-mapping.txt.  Convert the two cases of on-stack packet
payload buffers in firewire-core (payload of lock requests in the bus
manager work and in iso resource management) to slab-allocated memory.

There are a number on-stack buffers for quadlet write or quadlet read
requests in firewire-core and firewire-sbp2.  These are harmless; they
are copied to/ from card driver internal DMA buffers since quadlet
payloads are inlined with packet headers.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Decouple the creation and destruction of the net_device from the order
of discovery and removal of nodes with RFC 2734 unit directories since
there is no reliable order.  The net_device is now created when the
first RFC 2734 unit on a card is discovered, and destroyed when the last
RFC 2734 unit on a card went away.  This includes all remote units as
well as the local unit, which is therefore tracked as a peer now too.

Also, locking around the list of peers is slightly extended to guard
against peer removal.  As a side effect, fwnet_peer.pdg_lock has become
superfluous and is deleted.

Peer data (max_rec, speed, node ID, generation) are updated more
carefully.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Change names of types, variables, functions.
Omit debug code.
Use get_unaligned*, put_unaligned*.
Annotate big endian data.
Handle errors in __init.
Change whitespace.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Implement IPv4 over IEEE 1394 as per RFC 2734 for the newer firewire
stack.  This feature has only been present in the older ieee1394 stack
via the eth1394 driver.

Still to do:
  - fix ipv4_priv and ipv4_node lifetime logic
  - fix determination of speeds and max payloads
  - fix bus reset handling
  - fix unaligned memory accesses
  - fix coding style
  - further testing/ improvement of fragment reassembly
  - perhaps multicast support
Signed-off-by: NJay Fenlason <fenlason@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (rebased, copyright note, changelog)

Tlabel is a 6 bits wide datum.  Wrap it after 63 rather than 31 for more
safety against transaction label exhaustion and potential responders'
transaction layer bugs.  (As noted by Guus Sliepen, this change requires
an expansion of tlabel_mask to 64 bits.)
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This extra check will avoid Broadcast_Channel register related traffic
to many IIDC, SBP-2, and AV/C devices which aren't IRMC or have a
max_rec < 8 (i.e. support < 512 bytes async payload).  This avoids a
little bit of traffic after bus reset and is even more careful with
devices which don't implement this CSR.

The assumption is that no other protocol than IP over 1394 uses the
broadcast channel for streams.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Retrieval of an fw_unit's parent is a common pattern in high-level code.
Wrap it up as device = fw_parent_device(unit).
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The three header files of firewire-core, i.e.
 "drivers/firewire/fw-device.h",
 "drivers/firewire/fw-topology.h",
 "drivers/firewire/fw-transaction.h",
are replaced by
 "drivers/firewire/core.h",
 "include/linux/firewire.h".

The latter includes everything which a firewire high-level driver (like
firewire-sbp2) needs besides linux/firewire-constants.h, while core.h
contains the rest which is needed by firewire-core itself and by low-
level drivers (card drivers) like firewire-ohci.

High-level drivers can now also reside outside of drivers/firewire
without having to add drivers/firewire to the header file search path in
makefiles.  At least the firedtv driver will be such a driver.

I also considered to spread the contents of core.h over several files,
one for each .c file where the respective implementation resides.  But
it turned out that most core .c files will end up including most of the
core .h files.  Also, the combined core.h isn't unreasonably big, and it
will lose more of its contents to linux/firewire.h anyway soon when more
firewire drivers are added.  (IP-over-1394, firedtv, and there are plans
for one or two more.)

Furthermore, fw-ohci.h is renamed to ohci.h.  The name of core.h and
ohci.h is chosen with regard to name changes of the .c files in a
follow-up change.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>