- 14 1月, 2010 2 次提交
-
-
由 Ursula Braun 提交于
If a qeth device is set online, several initialisation steps are performed. If a failure in one of these steps occurs, the qeth device is reset into DOWN state. If due to the failure a qeth recovery is scheduled and started in another thread, this might cause all kinds of conflicts, even a kernel panic. The patch forbids scheduling of a qeth recovery while online processing is performed till the card is in state SOFTSETUP. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
New feature to trace HiperSockets network traffic for debugging purposes. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 12月, 2009 1 次提交
-
-
由 H Hartley Sweeten 提交于
Use the %pM kernel extension to display the MAC address. Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 11月, 2009 3 次提交
-
-
由 Frank Blaschka 提交于
The maximum TSO size OSA can handle is 15 * PAGE_SIZE. This patch reduces gso_max_size to this value and adds some sanity checks and statistics to the TSO implementation. Since only layer 3 is able to do TSO move all TSO related functions to the qeth_l3 module. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
Setting a qeth device online requires to call function ccw_device_set_online() for read-, write-, and data-subchannel. Failures should be detected immediately without an attempt to invoke follow-on activity qeth_qdio_clear_card()., In addition, ccw_device_set_online calls are consolidated in qeth_core_main.c only. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Einar Lueck 提交于
Isolate data connection to a shared OSA card against other data connections to the same OSA card. Connectivity between isolated data connections sharing the same OSA card is therefore possible only through external network gear (e.g. a router). Signed-off-by: NEinar Lueck <elelueck@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 10月, 2009 1 次提交
-
-
由 Ben Hutchings 提交于
This string query operation was supposed to be replaced by the generic get_sset_count() starting in 2007. Convert qeth's implementation. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 9月, 2009 1 次提交
-
-
由 Eric Dumazet 提交于
The generic packet receive code takes care of setting netdev->last_rx when necessary, for the sake of the bonding ARP monitor. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Acked-by: NNeil Horman <nhorman@txudriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 9月, 2009 1 次提交
-
-
由 Stephen Hemminger 提交于
No need to put ethtool_ops in data, they should be const. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 8月, 2009 1 次提交
-
-
由 Klaus-Dieter Wacker 提交于
Clear separation of cast-type determination (send path) for layer-2 resp. layer-3. Allowing to have inline functions for qeth layer- discipline. Signed-off-by: NKlaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 06 7月, 2009 1 次提交
-
-
由 Patrick McHardy 提交于
This patch converts the remaining occurences of raw return values to their symbolic counterparts in ndo_start_xmit() functions that were missed by the previous automatic conversion. Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero is changed to explicitly use NETDEV_TX_OK. Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 6月, 2009 1 次提交
-
-
由 Jiri Pirko 提交于
This patch is inspired by patch recently posted by Johannes Berg. Basically what my patch does is to group list and a count of addresses into newly introduced structure netdev_hw_addr_list. This brings us two benefits: 1) struct net_device becames a bit nicer. 2) in the future there will be a possibility to operate with lists independently on netdevices (with exporting right functions). I wanted to introduce this patch before I'll post a multicast lists conversion. Signed-off-by: NJiri Pirko <jpirko@redhat.com> drivers/net/bnx2.c | 4 +- drivers/net/e1000/e1000_main.c | 4 +- drivers/net/ixgbe/ixgbe_main.c | 6 +- drivers/net/mv643xx_eth.c | 2 +- drivers/net/niu.c | 4 +- drivers/net/virtio_net.c | 10 ++-- drivers/s390/net/qeth_l2_main.c | 2 +- include/linux/netdevice.h | 17 +++-- net/core/dev.c | 130 ++++++++++++++++++-------------------- 9 files changed, 89 insertions(+), 90 deletions(-) Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 6月, 2009 1 次提交
-
-
由 Frank Blaschka 提交于
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 30 5月, 2009 1 次提交
-
-
由 Jiri Pirko 提交于
This patch converts unicast address list to standard list_head using previously introduced struct netdev_hw_addr. It also relaxes the locking. Original spinlock (still used for multicast addresses) is not needed and is no longer used for a protection of this list. All reading and writing takes place under rtnl (with no changes). I also removed a possibility to specify the length of the address while adding or deleting unicast address. It's always dev->addr_len. The convertion touched especially e1000 and ixgbe codes when the change is not so trivial. Signed-off-by: NJiri Pirko <jpirko@redhat.com> drivers/net/bnx2.c | 13 +-- drivers/net/e1000/e1000_main.c | 24 +++-- drivers/net/ixgbe/ixgbe_common.c | 14 ++-- drivers/net/ixgbe/ixgbe_common.h | 4 +- drivers/net/ixgbe/ixgbe_main.c | 6 +- drivers/net/ixgbe/ixgbe_type.h | 4 +- drivers/net/macvlan.c | 11 +- drivers/net/mv643xx_eth.c | 11 +- drivers/net/niu.c | 7 +- drivers/net/virtio_net.c | 7 +- drivers/s390/net/qeth_l2_main.c | 6 +- drivers/scsi/fcoe/fcoe.c | 16 ++-- include/linux/netdevice.h | 18 ++-- net/8021q/vlan.c | 4 +- net/8021q/vlan_dev.c | 10 +- net/core/dev.c | 195 +++++++++++++++++++++++++++----------- net/dsa/slave.c | 10 +- net/packet/af_packet.c | 4 +- 18 files changed, 227 insertions(+), 137 deletions(-) Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 5月, 2009 2 次提交
-
-
由 Ursula Braun 提交于
z/VM Virtual Switch Port Isolation allows guests on a VLAN UNAWARE virtual switch to be isolated from other guests on the VSWITCH. (See z/VM Apars VM64281 and VM64463). The Linux qeth driver is affected, because it has to handle new error codes introduced with the z/VM VSWITCH Port Isolation support. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
If a qeth device is plugged off, setting the device online stops in state HARDSETUP and a failure is reported to the base cio-layer causing halt/clear to be invoked. Replugging the device again triggers a qeth recovery without notification of the cio-layer. If a device is ungrouped in this state, the qeth set_offline function is not invoked, because the corresponding ccwgroup device is not in state ONLINE. Then incoming traffic is still handled by the qdio layer resulting in a crash in qeth_l<x>_qdio_input_handler, because (part of) the qeth data structures for this device are already removed. Solution: After replugging the device qeth recovery should lead to a working net device. Thus a "LAN offline" result when setting a qeth device online must not report a failure to the base cio-layer. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 3月, 2009 4 次提交
-
-
由 Ursula Braun 提交于
When a recovery is started for a qeth device, additional invocations to change a mac address, to configure a VLAN interface on top, or to add multicast addresses should wait till recovery is finished, otherwise recovery might fail. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Klaus-Dieter Wacker 提交于
qeth: Unregister MAC addresses from device (layer 2) during recovery cycle. When the device is set online the MAC addresses are registered again on the device. Signed-off-by: NKlaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Frank Blaschka 提交于
Performance measurements showed EDDP does not lower CPU costs but increase them. So we dump out EDDP code from qeth driver. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Frank Blaschka 提交于
Add statistics counter for software tx checksumming. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 11 1月, 2009 1 次提交
-
-
由 Frank Blaschka 提交于
Have separate netdev_ops for OSA and HiperSocket/TR. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 09 1月, 2009 1 次提交
-
-
由 Frank Blaschka 提交于
qeth_l2, qeth_l3 convert to net_device_ops. qeth_l3 remove vlan neigh_setup hack since it does not work any longer with the new net_device_ops. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 1月, 2009 1 次提交
-
-
由 Mark McLoughlin 提交于
Replace s390_root_dev_register() with root_device_register() etc. [Includes fix from Cornelia Huck] Signed-off-by: NMark McLoughlin <markmc@redhat.com> Cc: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 05 1月, 2009 1 次提交
-
-
由 Ursula Braun 提交于
For z/VM GuestLAN or VSWITCH devices the transport layer is configured in z/VM. The layer2 attribute of a participating Linux device has to match the z/VM definition. In case of a mismatch Linux currently crashes in qeth recovery due to a reference to the not yet existing net_device. Solution: add a check for existence of net_device and add a message pointing to the mismatch of layer definitions in Linux and z/VM. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 12月, 2008 1 次提交
-
-
由 Frank Blaschka 提交于
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 28 10月, 2008 3 次提交
-
-
由 Johannes Berg 提交于
A number of places still use %02x:...:%02x because it's in debug statements or for no real reason. Make a few of them use %pM. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
To make the qeth driver more robust in case of malformatted inbound packets due to hardware problems, an additional check for OSN-card-type is added for OSN-type packets. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Ursula Braun 提交于
IP-threads have been removed from the qeth driver. Only the recover-thread is left over. This makes checkings for non-recover threads superfluous. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
- 25 9月, 2008 2 次提交
-
-
由 Ursula Braun 提交于
Do not touch IFF_UP flag during qeth recovery, but invoke dev_close() in case of failing recovery. Cancel outstanding control commands in case of Data Checks or Channel Checks. Do not invoke qeth_l2_del_all_mc() in case of a hard stop to speed up removal of qeth devices. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Ursula Braun 提交于
Real HiperSocket devices in layer2 mode have a firmware-created MAC-address. This change enables the qeth driver to use this firmware MAC-address for layer2 HiperSocket devices. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
- 27 8月, 2008 1 次提交
-
-
由 Frank Blaschka 提交于
In case the netdev unicast list contains additional entries we have to register/deregister them. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
- 01 8月, 2008 1 次提交
-
-
由 Frank Blaschka 提交于
For hiper socket devices this patch will economize the reallocation of the tx skb data segment by allocating separate memory for the qdio transport information (qeth header). Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 26 7月, 2008 1 次提交
-
-
由 Heiko Carstens 提交于
From: Heiko Carstens <heiko.carstens@de.ibm.com> This makes qeth working again after git commit e3c50d5d "netdev: netdev_priv() can now be sane again.". Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 7月, 2008 1 次提交
-
-
由 Jan Glauber 提交于
List of major changes: - split qdio driver into several files - seperation of thin interrupt code - improved handling for multiple thin interrupt devices - inbound and outbound processing now always runs in tasklet context - significant less tasklet schedules per interrupt needed - merged qebsm with non-qebsm handling - cleanup qdio interface and added kerneldoc - coding style Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com> Reviewed-by: NUtz Bacher <utz.bacher@de.ibm.com> Reviewed-by: NUrsula Braun <braunu@de.ibm.com> Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
-
- 11 6月, 2008 3 次提交
-
-
由 Frank Blaschka 提交于
In case the xmit function drop out with an error, we have to wake the netdevice queue to start another xmit. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Frank Blaschka 提交于
Remove unnecessary messages. Write important debug information to s390dbf. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Cornelia Huck 提交于
Get the devno from the ccw device via ccw_device_get_id() instead of parsing the bus_id. Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
- 29 4月, 2008 3 次提交
-
-
由 Frank Blaschka 提交于
Allow ethtool to turn on/off EDDP via ethtool TSO interface. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Frank Blaschka 提交于
Remove unnecessary traces. Remove unnecessary wrappers for skb functions. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Frank Blaschka 提交于
Load balancing bonding queries the speed of the slave interfaces. To support a bond consisting of different slave speeds we have to report the speed by ethtool settings. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-