Model drivers assume that model_data is zeroed, so we better use
kzalloc() (like we did before when it was allocated together with the
card structure).
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

If the EEPROM was partially overwritten (which seems to happen before the OS is
booted), restore its entire contents by deducing it from the remaining
information.

This does not have any effect on the Linux driver, which works even with
incomplete information in the EEPROM, but it makes other drivers work again.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Under as yet unknown circumstances, the first word of the sound card's
EEPROM gets overwritten.  When this has happened, we cannot rely on the
subsystem IDs that the kernel reads from the PCI configuration
registers.  Instead, we read the IDs directly from the EEPROM and do the
ID matching manually.

Because the model-specific driver cannot determine the model before
calling oxygen_pci_probe(), that function now gets a get_model()
callback as parameter.  The customizing of the model structure, which
was formerly done by the probe() callback, also has moved into
get_model().
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When allocating resources, use a fixed name instead of reading it from
the model structure.  This allows us to allocate the resources before
the actual model is known.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Allocate the model-specific data dynamically instead of including it in
the memory block of the card structure.  This will allow us to determine
the actual model after the card creation.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Move the owner field out of the oxygen_model structure and make it
a parameter of oxygen_pci_probe(), because the actual owner module does
not depend on the card model.  Furthermore, moving it out of the model
structure allows us to create the card structure before the actual model
is known.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Convert from snd_card_new() to the new snd_card_create() function
in sound/pci/*.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add functions to allow model drivers to communicate with external chips
by doing I/O with the not-used-for-MIDI UART.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

To enable the MIDI port, model drivers must now set flags in
device_config, not only in misc_flags.  This allows model drivers to
enable the UART without creating an ALSA MIDI device.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Rename the pcm_dev_cfg field to device_config because there will be
additional flags that do not describe PCM devices.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Add a probe callback to the model structure so that model-specific
drivers can refine their model detection before the card is initialized.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Put a copy of the model structure into the chip structure so that model-
specific drivers can modify it depending on a particular device
instance.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Add suspend/resume support.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Remove another magic number - add a symbol for the size of the PCI I/O
range.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Adjust the MODULE_LICENSE strings to properly reflect the actual license.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

free_irq() calls synchronize_irq() for you, so there is no need for
drivers to manually do the same thing (again).  Thus, calls where
sync-irq immediately precedes free-irq can be simplified.

However, during this audit several bugs were noticed, where free-irq is
preceded by a "irq >= 0" check... but the sync-irq call is not covered
by the same check.

So, where sync-irq could not be eliminated completely, the missing check
was added.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Initialize the playback volume controls as being muted and having
minimal volume.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add fields for the DAC volume limits to the module structure so that
model drivers do not need to install their own control info handlers.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

If the card model does not have a digital input or an AC97 codec,
disable the respective interrupt and mixer controls.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

On C-Media cards, the GPIO pin 0 of the CM9780 must be handled exactly
like on Xonar cards, so move the Xonar code to the common mixer code.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Disable the master clock outputs of any unused I2S inputs.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Put the flag that enables the MIDI port into the model structure instead
of passing it as a separate parameter to oxygen_pci_probe().
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Allow the model drivers to specify if the codec communication goes over
SPI or a 2-wire bus.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add controls to enable monitoring of the analog and digital inputs.

To allow monitoring after loading the driver when nothing has been
played back or recorded yet, the I2S input and outputs are initialized
to a valid configuration.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Removed invalid __devinit and __devexit that are remaining after
split to a helper module.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On the Xonar D2X, monitor the GPIO pin that indicates whether external
power is present.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add mixer controls for the front panel AC97 codec.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

After an AC97 register read or write, use the AC97 interrupt instead of
polling to wait for the access to be completed.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Move the line input switching code to the Virtuoso driver because only
the Xonar cards bypass the analog mixer for line input.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Initialize more registers of the controller and the second AC97 codec.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Change the oxygen_spdif_input_bits_changed() function so that clock
changes on the SPDIF input are correctly detected.  This means that
sample rates greater than 96 kHz are now supported.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Instead of having model-specific fields in the common struct oxygen, put
them into a private structure that is allocated together with the card
structure.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add symbol definitions for the various codecs and GPIO pins.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

The MIDI bit in the MISC register is set by default and cannot be used
to detect the presence of a MIDI port.  Instead, add a parameter to the
oxygen_pci_probe() function so that model drivers can specify this.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Replace some magic numbers with register symbols.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

The default playback routing must be 0xe4, not 0xe1; the front and
surround DACs were exchanged.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add more symbols for registers and register fields.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add a field to the model structure so that it is possible to have a card
where the SPI outputs 4 and 5 are used for an EEPROM.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Only initialize and create mixer controls for the first AC97 codec when
one has actually been detected.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Use an array for the pointers to known controls so that it is easier to
add more.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>