Skip to content

K
kernel_linux

OpenHarmony / kernel_linux
上一次同步 3 年多

通知 13
Star 8
Fork 2
K
kernel_linux
切换分支/标签
  1. 28 2月, 2009 2 次提交
    • S
      mac80211: Extend the rate control API with an update callback · 81cb7623
      由 Sujith 提交于 
      The AP can switch dynamically between 20/40 Mhz channel width,
in which case we switch the local operating channel, but the
rate control algorithm is not notified. This patch adds a new callback
to indicate such changes to the RC algorithm.

Currently, HT channel width change is notified, but this callback
can be used to indicate any new requirements that might come up later on.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      81cb7623
    • J
      mac80211: fix aggregation for hardware with ampdu queues · 96f5e66e
      由 Johannes Berg 提交于 
      Hardware with AMPDU queues currently has broken aggregation.

This patch fixes it by making all A-MPDUs go over the regular AC queues,
but keeping track of the hardware queues in mac80211. As a first rough
version, it actually stops the AC queue for extended periods of time,
which can be removed by adding buffering internal to mac80211, but is
currently not a huge problem because people rarely use multiple TIDs
that are in the same AC (and iwlwifi currently doesn't operate as AP).

This is a short-term fix, my current medium-term plan, which I hope to
execute soon as well, but am not sure can finish before .30, looks like
this:
 1) rework the internal queuing layer in mac80211 that we use for
    fragments if the driver stopped queue in the middle of a fragmented
    frame to be able to queue more frames at once (rather than just a
    single frame with its fragments)
 2) instead of stopping the entire AC queue, queue up the frames in a
    per-station/per-TID queue during aggregation session initiation,
    when the session has come up take all those frames and put them
    onto the queue from 1)
 3) push the ampdu queue layer abstraction this patch introduces in
    mac80211 into the driver, and remove the virtual queue stuff from
    mac80211 again

This plan will probably also affect ath9k in that mac80211 queues the
frames instead of passing them down, even when there are no ampdu queues.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      96f5e66e
  3. 14 2月, 2009 2 次提交
  5. 10 2月, 2009 1 次提交
  7. 30 1月, 2009 19 次提交
  9. 17 1月, 2009 1 次提交
  11. 20 12月, 2008 3 次提交
  13. 13 12月, 2008 3 次提交
  15. 05 12月, 2008 3 次提交
  17. 22 11月, 2008 3 次提交
  19. 19 11月, 2008 1 次提交
    • J
      mac80211: remove ieee80211_notify_mac · 8e3bad65
      由 Johannes Berg 提交于 
      Before ieee80211_notify_mac() was added, it was presented with the
use case of using it to tell mac80211 that the association may
have been lost because the firmware crashed/reset.

Since then, it has also been used by iwlwifi to (slightly) speed
up re-association after resume, a workaround around the fact that
mac80211 has no suspend/resume handling yet. It is also not used
by any other drivers, so clearly it cannot be necessary for "good
enough" suspend/resume.

Unfortunately, the callback suffers from a severe problem: It only
works for station mode. If suspend/resume happens while in IBSS or
any other mode (but station), then the callback is pointless.

Recently, it has created a number of locking issues, first because
it required rtnl locking rather than RCU due to calling sleeping
functions within the critical section, and now because it's called
by iwlwifi from the mac80211 workqueue that may not use the rtnl
because it is flushed under rtnl.
(cf. http://bugzilla.kernel.org/show_bug.cgi?id=12046)

I think, therefore, that we should take a step back, remove it
entirely for now and add the small feature it provided properly.
For suspend and resume we will need to introduce new hooks, and for
the case where the firmware was reset the driver will probably
simply just pretend it has done a suspend/resume cycle to get
mac80211 to reprogram the hardware completely, not just try to
connect to the current AP again in station mode. When doing so, we
will need to take into account locking issues and possibly defer
to schedule_work from within mac80211 for the resume operation,
while the suspend operation must be done directly.

Proper suspend/resume should also not necessarily try to reconnect
to the current AP, the time spent in suspend may have been short
enough to not be disconnected from the AP, mac80211 will detect
that the AP went out of range quickly if it did, and if the
association is lost then the AP will disassoc as soon as a data
frame is sent. We might also take into account WWOL then, and
have mac80211 program the hardware into such a mode where it is
available and requested.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      8e3bad65
  21. 11 11月, 2008 2 次提交