__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

PGALLOC_GFP uses __GFP_REPEAT but it is only used in pte_alloc_one,
pte_alloc_one_kernel which does order-0 request.  This means that this
flag has never been actually useful here because it has always been used
only for PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-17-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

pgtable_alloc_one uses __GFP_REPEAT flag for L2_USER_PGTABLE_ORDER but
the order is either 0 or 3 if L2_KERNEL_PGTABLE_SHIFT for HPAGE_SHIFT.
This means that this flag has never been actually useful here because it
has always been used only for PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-16-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Acked-by: Chris Metcalf <cmetcalf@mellanox.com> [for tile]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

PGALLOC_GFP uses __GFP_REPEAT but {pgd,pmd}_alloc allocate from
{pgd,pmd}_cache but both caches are allocating up to PAGE_SIZE objects.
This means that this flag has never been actually useful here because it
has always been used only for PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-15-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

page_table_alloc then uses the flag for a single page allocation.  This
means that this flag has never been actually useful here because it has
always been used only for PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-14-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

{pud,pmd}_alloc_one is using __GFP_REPEAT but it always allocates from
pgtable_cache which is initialzed to PAGE_SIZE objects.  This means that
this flag has never been actually useful here because it has always been
used only for PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-13-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

{pud,pmd}_alloc_one are allocating from {PGT,PUD}_CACHE initialized in
pgtable_cache_init which doesn't have larger than sizeof(void *) << 12
size and that fits into !costly allocation request size.

PGALLOC_GFP is used only in radix__pgd_alloc which uses either order-0
or order-4 requests.  The first one doesn't need the flag while the
second does.  Drop __GFP_REPEAT from PGALLOC_GFP and add it for the
order-4 one.

This means that this flag has never been actually useful here because it
has always been used only for PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-12-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

pte_alloc_one{_kernel} allocate PTE_ORDER which is 0.  This means that
this flag has never been actually useful here because it has always been
used only for PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-11-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

pmd_alloc_one allocate PMD_ORDER which is 1.  This means that this flag
has never been actually useful here because it has always been used only
for PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-10-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

pte_alloc_one{_kernel} allocate PTE_ORDER which is 0.  This means that
this flag has never been actually useful here because it has always been
used only for PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-9-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Cc: Ley Foon Tan <lftan@altera.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

pte_alloc_one{_kernel}, pmd_alloc_one allocate PTE_ORDER resp.
PMD_ORDER but both are not larger than 1.  This means that this flag has
never been actually useful here because it has always been used only for
PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-8-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

pte_alloc_one_kernel uses __get_order_pte but this is obviously always
zero because BITS_FOR_PTE is not larger than 9 yet the page size is
always larger than 4K.  This means that this flag has never been
actually useful here because it has always been used only for
PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-7-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NVineet Gupta <vgupta@synopsys.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

{pte,pmd,pud}_alloc_one{_kernel}, late_pgtable_alloc use PGALLOC_GFP for
__get_free_page (aka order-0).

pgd_alloc is slightly more complex because it allocates from pgd_cache
if PGD_SIZE != PAGE_SIZE and PGD_SIZE depends on the configuration
(CONFIG_ARM64_VA_BITS, PAGE_SHIFT and CONFIG_PGTABLE_LEVELS).

As per
config PGTABLE_LEVELS
	int
	default 2 if ARM64_16K_PAGES && ARM64_VA_BITS_36
	default 2 if ARM64_64K_PAGES && ARM64_VA_BITS_42
	default 3 if ARM64_64K_PAGES && ARM64_VA_BITS_48
	default 3 if ARM64_4K_PAGES && ARM64_VA_BITS_39
	default 3 if ARM64_16K_PAGES && ARM64_VA_BITS_47
	default 4 if !ARM64_64K_PAGES && ARM64_VA_BITS_48

we should have the following options

  CONFIG_ARM64_VA_BITS:48 CONFIG_PGTABLE_LEVELS:4 PAGE_SIZE:4k size:4096 pages:1
  CONFIG_ARM64_VA_BITS:48 CONFIG_PGTABLE_LEVELS:4 PAGE_SIZE:16k size:16 pages:1
  CONFIG_ARM64_VA_BITS:48 CONFIG_PGTABLE_LEVELS:3 PAGE_SIZE:64k size:512 pages:1
  CONFIG_ARM64_VA_BITS:47 CONFIG_PGTABLE_LEVELS:3 PAGE_SIZE:16k size:16384 pages:1
  CONFIG_ARM64_VA_BITS:42 CONFIG_PGTABLE_LEVELS:2 PAGE_SIZE:64k size:65536 pages:1
  CONFIG_ARM64_VA_BITS:39 CONFIG_PGTABLE_LEVELS:3 PAGE_SIZE:4k size:4096 pages:1
  CONFIG_ARM64_VA_BITS:36 CONFIG_PGTABLE_LEVELS:2 PAGE_SIZE:16k size:16384 pages:1

All of them fit into a single page (aka order-0).  This means that this
flag has never been actually useful here because it has always been used
only for PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-6-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

efi_alloc_page_tables uses __GFP_REPEAT but it allocates an order-0
page.  This means that this flag has never been actually useful here
because it has always been used only for PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-4-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NMatt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

PGALLOC_GFP uses __GFP_REPEAT but none of the allocation which uses this
flag is for more than order-0.  This means that this flag has never been
actually useful here because it has always been used only for
PAGE_ALLOC_COSTLY requests.

Link: http://lkml.kernel.org/r/1464599699-30131-3-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is the third version of the patchset previously sent [1].  I have
basically only rebased it on top of 4.7-rc1 tree and dropped "dm: get
rid of superfluous gfp flags" which went through dm tree.  I am sending
it now because it is tree wide and chances for conflicts are reduced
considerably when we want to target rc2.  I plan to send the next step
and rename the flag and move to a better semantic later during this
release cycle so we will have a new semantic ready for 4.8 merge window
hopefully.

Motivation:

While working on something unrelated I've checked the current usage of
__GFP_REPEAT in the tree.  It seems that a majority of the usage is and
always has been bogus because __GFP_REPEAT has always been about costly
high order allocations while we are using it for order-0 or very small
orders very often.  It seems that a big pile of them is just a
copy&paste when a code has been adopted from one arch to another.

I think it makes some sense to get rid of them because they are just
making the semantic more unclear.  Please note that GFP_REPEAT is
documented as

* __GFP_REPEAT: Try hard to allocate the memory, but the allocation attempt

* _might_ fail.  This depends upon the particular VM implementation.
  while !costly requests have basically nofail semantic.  So one could
  reasonably expect that order-0 request with __GFP_REPEAT will not loop
  for ever.  This is not implemented right now though.

I would like to move on with __GFP_REPEAT and define a better semantic
for it.

  $ git grep __GFP_REPEAT origin/master | wc -l
  111
  $ git grep __GFP_REPEAT | wc -l
  36

So we are down to the third after this patch series.  The remaining
places really seem to be relying on __GFP_REPEAT due to large allocation
requests.  This still needs some double checking which I will do later
after all the simple ones are sorted out.

I am touching a lot of arch specific code here and I hope I got it right
but as a matter of fact I even didn't compile test for some archs as I
do not have cross compiler for them.  Patches should be quite trivial to
review for stupid compile mistakes though.  The tricky parts are usually
hidden by macro definitions and thats where I would appreciate help from
arch maintainers.

[1] http://lkml.kernel.org/r/1461849846-27209-1-git-send-email-mhocko@kernel.org

This patch (of 19):

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.  Yet we
have the full kernel tree with its usage for apparently order-0
allocations.  This is really confusing because __GFP_REPEAT is
explicitly documented to allow allocation failures which is a weaker
semantic than the current order-0 has (basically nofail).

Let's simply drop __GFP_REPEAT from those places.  This would allow to
identify place which really need allocator to retry harder and formulate
a more specific semantic for what the flag is supposed to do actually.

Link: http://lkml.kernel.org/r/1464599699-30131-2-git-send-email-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com> [for tile]
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: John Crispin <blogic@openwrt.org>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The INIT_TASK() initializer was similarly confused about the stack vs
thread_info allocation that the allocators had, and that were fixed in
commit b235beea ("Clarify naming of thread info/stack allocators").

The task ->stack pointer only incidentally ends up having the same value
as the thread_info, and in fact that will change.

So fix the initial task struct initializer to point to 'init_stack'
instead of 'init_thread_info', and make sure the ia64 definition for
that exists.

This actually makes the ia64 tsk->stack pointer be sensible for the
initial task, but not for any other task.  As mentioned in commit
b235beea, that whole pointer isn't actually used on ia64, since
task_stack_page() there just points to the (single) allocation.

All the other architectures seem to have copied the 'init_stack'
definition, even if it tended to be generally unusued.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As the actual pointer value is the same for the thread stack allocation
and the thread_info, code that confused the two worked fine, but will
break when the thread info is moved away from the stack allocation.  It
also looks very confusing.

For example, the kprobe code wanted to know the current top of stack.
To do that, it used this:

	(unsigned long)current_thread_info() + THREAD_SIZE

which did indeed give the correct value.  But it's not only a fairly
nonsensical expression, it's also rather complex, especially since we
actually have this:

	static inline unsigned long current_top_of_stack(void)

which not only gives us the value we are interested in, but happens to
be how "current_thread_info()" is currently defined as:

	(struct thread_info *)(current_top_of_stack() - THREAD_SIZE);

so using current_thread_info() to figure out the top of the stack really
is a very round-about thing to do.

The other cases are just simpler confusion about task_thread_info() vs
task_stack_page(), which currently return the same pointer - but if you
want the stack page, you really should be using the latter one.

And there was one entirely unused assignment of the current stack to a
thread_info pointer.

All cleaned up to make more sense today, and make it easier to move the
thread_info away from the stack in the future.

No semantic changes.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We've had the thread info allocated together with the thread stack for
most architectures for a long time (since the thread_info was split off
from the task struct), but that is about to change.

But the patches that move the thread info to be off-stack (and a part of
the task struct instead) made it clear how confused the allocator and
freeing functions are.

Because the common case was that we share an allocation with the thread
stack and the thread_info, the two pointers were identical.  That
identity then meant that we would have things like

	ti = alloc_thread_info_node(tsk, node);
	...
	tsk->stack = ti;

which certainly _worked_ (since stack and thread_info have the same
value), but is rather confusing: why are we assigning a thread_info to
the stack? And if we move the thread_info away, the "confusing" code
just gets to be entirely bogus.

So remove all this confusion, and make it clear that we are doing the
stack allocation by renaming and clarifying the function names to be
about the stack.  The fact that the thread_info then shares the
allocation is an implementation detail, and not really about the
allocation itself.

This is a pure renaming and type fix: we pass in the same pointer, it's
just that we clarify what the pointer means.

The ia64 code that actually only has one single allocation (for all of
task_struct, thread_info and kernel thread stack) now looks a bit odd,
but since "tsk->stack" is actually not even used there, that oddity
doesn't matter.  It would be a separate thing to clean that up, I
intentionally left the ia64 changes as a pure brute-force renaming and
type change.
Acked-by: NAndy Lutomirski <luto@amacapital.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

None of the code actually wants a thread_info, it all wants a
task_struct, and it's just converting to a thread_info pointer much too
early.

No semantic change.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When page tables entries are set using xen_set_pte_init() during early
boot there is no page fault handler that could handle a fault when
performing an M2P lookup.

In 64 bit guests (usually dom0) early_ioremap() would fault in
xen_set_pte_init() because an M2P lookup faults because the MFN is in
MMIO space and not mapped in the M2P.  This lookup is done to see if
the PFN in in the range used for the initial page table pages, so that
the PTE may be set as read-only.

The M2P lookup can be avoided by moving the check (and clear of RW)
earlier when the PFN is still available.
Reported-by: NKevin Moraga <kmoragas@riseup.net>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: NJuergen Gross <jgross@suse.com>

xen_cleanhighmap() is operating on level2_kernel_pgt only. The upper
bound of the loop setting non-kernel-image entries to zero should not
exceed the size of level2_kernel_pgt.
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Classic BPF JIT was never ported completely to work on little endian
powerpc. However, it can be enabled and will crash the system when used.
As such, disable use of BPF JIT on ppc64le.

Fixes: 7c105b63 ("powerpc: Add CONFIG_CPU_LITTLE_ENDIAN kernel config option.")
Reported-by: NThadeu Lima de Souza Cascardo <cascardo@redhat.com>
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: NThadeu Lima de Souza Cascardo <cascardo@redhat.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

As part of the Radix MMU support we added some feature sections in the
SLB miss handler. These are intended to catch the case that we
incorrectly take an SLB miss when Radix is enabled, and instead of
crashing weirdly they bail out to a well defined exit path and trigger
an oops.

However the way they were written meant the bailout case was enabled by
default until we did CPU feature patching.

On powermacs the early debug prints in setup_system() can cause an SLB
miss, which happens before code patching, and so the SLB miss handler
would incorrectly bailout and crash during boot.

Fix it by inverting the sense of the feature section, so that the code
which is in place at boot is correct for the hash case. Once we
determine we are using Radix - which will never happen on a powermac -
only then do we patch in the bailout case which unconditionally jumps.

Fixes: caca285e ("powerpc/mm/radix: Use STD_MMU_64 to properly isolate hash related code")
Reported-by: NDenis Kirjanov <kda@linux-powerpc.org>
Tested-by: NDenis Kirjanov <kda@linux-powerpc.org>
Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Hibernate relies on cpu hotplug to prevent secondary cores executing
the kernel text while it is being restored.

Add a call to cpus_are_stuck_in_kernel() to determine if there are
CPUs not counted by 'num_online_cpus()', and prevent hibernate in this
case.

Fixes: 82869ac5 ("arm64: kernel: Add support for hibernate/suspend-to-disk")
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

kernel/smp.c has a fancy counter that keeps track of the number of CPUs
it marked as not-present and left in cpu_park_loop(). If there are any
CPUs spinning in here, features like kexec or hibernate may release them
by overwriting this memory.

This problem also occurs on machines using spin-tables to release
secondary cores.
After commit 44dbcc93 ("arm64: Fix behavior of maxcpus=N")
we bring all known cpus into the secondary holding pen, meaning this
memory can't be re-used by kexec or hibernate.

Add a function cpus_are_stuck_in_kernel() to determine if either of these
cases have occurred.
Signed-off-by: NJames Morse <james.morse@arm.com>
Acked-by: NMark Rutland <mark.rutland@arm.com>
Reviewed-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

__sync_icache_dcache unconditionally skips the cache maintenance for
anonymous pages, under the assumption that flushing is only required in
the presence of D-side aliases [see 7249b79f ("arm64: Do not flush
the D-cache for anonymous pages")].

Unfortunately, this breaks migration of anonymous pages holding
self-modifying code, where userspace cannot be reasonably expected to
reissue maintenance instructions in response to a migration.

This patch fixes the problem by removing the broken page_mapping(page)
check from the cache syncing code, otherwise we may end up fetching and
executing stale instructions from the PoU.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NShaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

I fixed boot image dependencies for arch/arm in commit 3939f334
("ARM: 8418/1: add boot image dependencies to not generate invalid
images").

I see a similar problem for arch/arm64; "make -jN Image Image.gz"
would sometimes end up generating bad images where N > 1.

Fix the dependency in arch/arm64/Makefile to avoid the race
between "make Image" and "make Image.*".
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

During a rollover, we mark the active ASID on each CPU as reserved, before
allocating a new ID for the task that caused the rollover. This means that
with N CPUs, we can only guarantee the new task to obtain a valid ASID if
we have at least N+1 ASIDs. Update this limit in the initcall check.

Note that this restriction was introduced by commit 8e648066 on the
arch/arm side, which disallow re-using the previously active ASID on the
local CPU, as it would introduce a TLB race.

In addition, we only dispose of NUM_USER_ASIDS-1, since ASID 0 is
reserved. Add this restriction as well.
Signed-off-by: NJean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

This patch fixes a non-booting issue in Mainline.

When booting with a compressed kernel, we need to be careful how we
populate memory close to DDR start.  AUTO_ZRELADDR is enabled by default
in multi-arch enabled configurations, which place some restrictions on
where the kernel is placed and where it will be uncompressed to on boot.

AUTO_ZRELADDR takes the decompressor code's start address and masks out
the bottom 28 bits to obtain an address to uncompress the kernel to
(thus a load address of 0x42000000 means that the kernel will be
uncompressed to 0x40000000 i.e. DDR START on this platform).

Even changing the load address to after the co-processor's shared memory
won't render a booting platform, since the AUTO_ZRELADDR algorithm still
ensures the kernel is uncompressed into memory shared with the first
co-processor (0x40000000).

Another option would be to move loading to 0x4A000000, since this will
mean the decompressor will decompress the kernel to 0x48000000. However,
this would mean a large chunk (0x44000000 => 0x48000000 (64MB)) of
memory would essentially be wasted for no good reason.

Until we can work with ST to find a suitable memory location to
relocate co-processor shared memory, let's disable the shared memory
nodes.  This will ensure a working platform in the mean time.

NB: The more observant of you will notice that we're leaving the DMU
shared memory node enabled; this is because a) it is the only one in
active use at the time of this writing and b) it is not affected by
the current default behaviour which is causing issues.

Fixes: fe135c63 (ARM: dts: STiH407: Move over to using the 'reserved-memory' API for obtaining DMA memory)
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Reviewed-by Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Several modern devices, such as PC/104 cards, are expected to run on
modern systems via an ISA bus interface. Since ISA is a legacy interface
for most modern architectures, ISA support should remain disabled in
general. Support for ISA-style drivers should be enabled on a per driver
basis.

To allow ISA-style drivers on modern systems, this patch introduces the
ISA_BUS_API and ISA_BUS Kconfig options. The ISA bus driver will now
build conditionally on the ISA_BUS_API Kconfig option, which defaults to
the legacy ISA Kconfig option. The ISA_BUS Kconfig option allows the
ISA_BUS_API Kconfig option to be selected on architectures which do not
enable ISA (e.g. X86_64).

The ISA_BUS Kconfig option is currently only implemented for X86
architectures. Other architectures may have their own ISA_BUS Kconfig
options added as required.
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.

When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.

Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: NAparna Balasubramanian <aparnab@ti.com>
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The PE primary bus cannot be got from its child devices when having
full hotplug in error recovery. The PE primary bus is cached, which
is done in commit <05ba75f8> ("powerpc/eeh: Fix stale cached primary
bus"). In eeh_reset_device(), the flag (EEH_PE_PRI_BUS) is cleared
before the PCI hot remove. eeh_pe_bus_get() then returns NULL as the
PE primary bus in pnv_eeh_reset() and it crashes the kernel eventually.

This fixes the issue by clearing the flag (EEH_PE_PRI_BUS) before the
PCI hot add. With it, the PowerNV EEH reset backend (pnv_eeh_reset())
can get valid PE primary bus through eeh_pe_bus_get().

Fixes: 67086e32 ("powerpc/eeh: powerpc/eeh: Support error recovery for VF PE")
Reported-by: NPridhiviraj Paidipeddi <ppaiddipe@in.ibm.com>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

ISA 3.0 updated it to be encoded as Radix tree size = 2^(RTS + 31). We
have it encoded as 2^(RTS + 28). Add a helper with the correct encoding
and use it instead of opencoding.

Fixes: 2bfd65e4 ("powerpc/mm/radix: Add radix callbacks for early init routines")
Reviewed-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

H_ENTER hcall handling in qemu had assumptions that a cache inhibited
hpte entry won't have memory conference set. Also older kernel
mentioned that some version of pHyp required this (the code removed
by the below commit says:

    /* Make pHyp happy */
    if ((rflags & _PAGE_NO_CACHE) && !(rflags & _PAGE_WRITETHRU))
            hpte_r &= ~HPTE_R_M;

But with older kernel we had some inconsistent memory conherence
mapping. We always enabled memory conherence in the page fault path and
removed memory conherence is _PAGE_NO_CACHE was set when we mapped the
page via htab_bolt_mapping. The commit mentioned below tried to
consolidate that by always enabling memory conherence. But as mentioned
above that breaks Qemu H_ENTER handling.

This patch update this such that we enable memory conherence only if
cache inhibited is not set and bring fault handling, lpar and bolt
mapping in sync.

Fixes: commit 30bda41a("powerpc/mm: Drop WIMG in favour of new constant")
Reported-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

A few platforms are currently missing clocksource_probe() completely
in their time_init functionality. On OMAP3430 for example, this is
causing cpuidle to be pretty much dead, as the counter32k is not
going to be registered and instead a gptimer is used as a clocksource.
This will tick in periodic mode, preventing any deeper idle states.

While here, also drop one unnecessary check for populated DT before
existing clocksource_probe() call.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

After OMAP1 IRQ definitions have been changed by commit 685e2d08
("ARM: OMAP1: Change interrupt numbering for sparse IRQ") introduced
in v4.2, ams-delta FIQ handler which depends on them no longer works
as expected. Fix it.

Created and tested on Amstrad Delta against Linux-4.7-rc3
Signed-off-by: NJanusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Current versions of gdb do not interoperate cleanly with kgdb on arm64
systems because gdb and kgdb do not use the same register description.
This patch modifies kgdb to work with recent releases of gdb (>= 7.8.1).

Compatibility with gdb (after the patch is applied) is as follows:

  gdb-7.6 and earlier  Ok
  gdb-7.7 series       Works if user provides custom target description
  gdb-7.8(.0)          Works if user provides custom target description
  gdb-7.8.1 and later  Ok

When commit 44679a4f ("arm64: KGDB: Add step debugging support") was
introduced it was paired with a gdb patch that made an incompatible
change to the gdbserver protocol. This patch was eventually merged into
the gdb sources:
https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commit;h=a4d9ba85ec5597a6a556afe26b712e878374b9dd

The change to the protocol was mostly made to simplify big-endian support
inside the kernel gdb stub. Unfortunately the gdb project released
gdb-7.7.x and gdb-7.8.0 before the protocol incompatibility was identified
and reversed:
https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commit;h=bdc144174bcb11e808b4e73089b850cf9620a7ee

This leaves us in a position where kgdb still uses the no-longer-used
protocol; gdb-7.8.1, which restored the original behaviour, was
released on 2014-10-29.

I don't believe it is possible to detect/correct the protocol
incompatiblity which means the kernel must take a view about which
version of the gdb remote protocol is "correct". This patch takes the
view that the original/current version of the protocol is correct
and that version found in gdb-7.7.x and gdb-7.8.0 is anomalous.
Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

On s390, there are two different hardware PMUs for counting and
sampling.  Previously, both PMUs have shared the perf_hw_context
which is not correct and, recently, results in this warning:

    ------------[ cut here ]------------
    WARNING: CPU: 5 PID: 1 at kernel/events/core.c:8485 perf_pmu_register+0x420/0x428
    Modules linked in:
    CPU: 5 PID: 1 Comm: swapper/0 Not tainted 4.7.0-rc1+ #2
    task: 00000009c5240000 ti: 00000009c5234000 task.ti: 00000009c5234000
    Krnl PSW : 0704c00180000000 0000000000220c50 (perf_pmu_register+0x420/0x428)
               R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3
    Krnl GPRS: ffffffffffffffff 0000000000b15ac6 0000000000000000 00000009cb440000
               000000000022087a 0000000000000000 0000000000b78fa0 0000000000000000
               0000000000a9aa90 0000000000000084 0000000000000005 000000000088a97a
               0000000000000004 0000000000749dd0 000000000022087a 00000009c5237cc0
    Krnl Code: 0000000000220c44: a7f4ff54            brc     15,220aec
               0000000000220c48: 92011000           mvi     0(%r1),1
              #0000000000220c4c: a7f40001           brc     15,220c4e
              >0000000000220c50: a7f4ff12           brc     15,220a74
               0000000000220c54: 0707               bcr     0,%r7
               0000000000220c56: 0707               bcr     0,%r7
               0000000000220c58: ebdff0800024       stmg    %r13,%r15,128(%r15)
               0000000000220c5e: a7f13fe0           tmll    %r15,16352
    Call Trace:
    ([<000000000022087a>] perf_pmu_register+0x4a/0x428)
    ([<0000000000b2c25c>] init_cpum_sampling_pmu+0x14c/0x1f8)
    ([<0000000000100248>] do_one_initcall+0x48/0x140)
    ([<0000000000b25d26>] kernel_init_freeable+0x1e6/0x2a0)
    ([<000000000072bda4>] kernel_init+0x24/0x138)
    ([<000000000073495e>] kernel_thread_starter+0x6/0xc)
    ([<0000000000734958>] kernel_thread_starter+0x0/0xc)
    Last Breaking-Event-Address:
     [<0000000000220c4c>] perf_pmu_register+0x41c/0x428
    ---[ end trace 0c6ef9f5b771ad97 ]---

Using the perf_sw_context is an option because the cpum_cf PMU does
not use interrupts.  To make this more clear, initialize the
capabilities in the PMU structure.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Suggested-by: NPeter Zijlstra <peterz@infradead.org>
Acked-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

VT-d posted interrupt is relying on the CPU side's posted interrupt.
Need to check whether VCPU's APICv is active before enabing VT-d
posted interrupt.

Fixes: d62caabb
Cc: stable@vger.kernel.org
Signed-off-by: NYang Zhang <yang.zhang.wz@gmail.com>
Signed-off-by: NShengge Ding <shengge.dsg@alibaba-inc.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Add logic to disable AVIC #ifndef CONFIG_X86_LOCAL_APIC.
Suggested-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NSuravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>