Damir Perisa <damir.perisa@solnet.ch> reports:

 drivers/net/s2io.h:765: error: invalid lvalue in assignment
 drivers/net/s2io.h:766: error: invalid lvalue in assignment

That's a gcc4 error.  I don't see why the casts are there anyway..

Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Make MODULE_DEVICE_TABLE work for vio devices.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Update version and add 4 minor fixes, the last 2 were suggested by
Jeff Garzik:

1. check for a valid ethernet address before setting it
2. zero out bp->regview if init_one encounters an error and unmaps
   the IO address. This prevents remove_one from unmapping again.
3. use netif_rx_schedule() instead of hand coding the same.
4. use IRQ_HANDLED and IRQ_NONE.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change all locks from spin_lock_irqsave() to spin_lock_bh(). All
places that require spinlocks are in BH context.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove atomic operations in the fast tx path. Expensive atomic
operations were used to keep track of the number of available tx
descriptors. The new code uses the difference between the consumer
and producer index to determine the number of free tx descriptors.

As suggested by Jeff Garzik, the name of the inline function is
changed to all lower case.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This speeds up link-up time on 5706 SerDes if the link partner does
not autoneg, a rather common scenario in blade servers. Some blade
servers use IPMI for keyboard input and it's important to minimize
link disruptions.

The speedup is achieved by shortening the timer to (HZ / 3) during
the transient period right after initiating a SerDes autoneg. If
autoneg does not complete, parallel detect can be done sooner. After
the transient period is over, the timer goes back to its normal HZ
interval.

As suggested by Jeff Garzik, the timer initialization is moved to
bnx2_init_board() from bnx2_open().

An eeprom bit is also added to allow default forced SerDes speed for
even faster link-up time.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes an rtnl deadlock problem when flush_scheduled_work() is
called from bnx2_close(). In rare cases, linkwatch_event() may be on
the workqueue from a previous close of a different device and it will
try to get the rtnl lock which is already held by dev_close().

The fix is to set a flag if we are in the reset task which is run
from the workqueue. bnx2_close() will loop until the flag is cleared.
As suggested by Jeff Garzik, the loop is changed to call msleep(1)
instead of yield() in the original patch.

flush_scheduled_work() is also moved to bnx2_remove_one() before the
netdev is freed.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch contains the following possible cleanups/fixes:

- use C99 struct initializers
- make a few arrays and structs static
- remove a few uses of literal 0 as NULL pointer
- use convenience function instead of cast+dereference in bnx2_ioctl()
- remove superfluous casts to u8 * in calls to readl/writel
Signed-off-by: NPeter Hagervall <hager@cs.umu.se>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Found a bug while reviewing the patches the second time.

The TG3_FLAG_TXD_MBOX_HWBUG flag is set after the register access
methods have been determined. This patch fixes it by moving it up before
the various access methods are assigned.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The register write to register 0x68 to restart interrupts is unnecessary
as the interrupt wasn't masked in that register by the irq handler. This
will save one register write in the fast path.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the new workaround for 5703 A1/A2 if it is behind
certain ICH bridges. The workaround disables memory and uses config.
cycles only to access all registers. The 5702/03 chips can mistakenly
decode the special cycles from the ICH chipsets as memory write cycles,
causing corruption of register and memory space. Only certain ICH
bridges will drive special cycles with non-zero data during the address
phase which can fall within the 5703's address range. This is not an ICH
bug as the PCI spec allows non-zero address during special cycles.
However, only these ICH bridges are known to drive non-zero addresses
during special cycles.

The indirect_lock is also changed to spin_lock_irqsave from spin_lock_bh
because it is used in irq handler when using the indirect method to
disable interrupts.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the mailbox read method and also adds an inline function
tw32_mailbox_f() for mailbox writes that require read flush.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds various dedicated register read/write methods for the
existing workarounds, including PCIX target workaround, write with read
flush, etc. The chips that require these workarounds will use these
dedicated access functions.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the basic function pointers to do register accesses in
the fast path. This was suggested by David Miller. The idea is that
various register access methods for different hardware errata can easily
be implemented with these function pointers and performance will not be
degraded on chips that use normal register access methods.

The various register read write macros (e.g. tw32, tr32, tw32_mailbox)
are redefined to call the function pointers.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead, set it in one place, namely the beginning of
netif_receive_skb().

Based upon suggestions from Jamal Hadi Salim.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bonding just wants the device before the skb_bond()
decapsulation occurs, so simply pass that original
device into packet_type->func() as an argument.

It remains to be seen whether we can use this same
exact thing to get rid of skb->input_dev as well.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This removes the private element from skbuff, that is only used by
HIPPI. Instead it uses skb->cb[] to hold the additional data that is
needed in the output path from hard_header to device driver.

PS: The only qdisc that might potentially corrupt this cb[] is if
netem was used over HIPPI. I will take care of that by fixing netem
to use skb->stamp. I don't expect many users of netem over HIPPI
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the "list" member of struct sk_buff, as it is entirely
redundant.  All SKB list removal callers know which list the
SKB is on, so storing this in sk_buff does nothing other than
taking up some space.

Two tricky bits were SCTP, which I took care of, and two ATM
drivers which Francois Romieu <romieu@fr.zoreil.com> fixed
up.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds back the code that was taken out, thus re-enabling:

* The PHY Layer to initialize without crashing
* Drivers to actually connect to PHYs
* The entire PHY Control Layer

This patch is used by the gianfar driver, and other drivers which are in
development.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Both revisions share the same PCI device ID and vendor ID but revision 2
of the device uses SysKonnect's chipset whereas revision 3 of the device
uses Realtek's 8169 chipset.

Credit goes to Christiaan Lutzer <mythtv.lutzer@gmail.com> for reporting
the issue and giving the actual value for the different revisions.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Rewrite the mkiss driver to make it SMP-proof following the example of
6pack.c.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Don't check type of sax25_family; dev_set_mac_address has already done
that before and anyway, the type to check against would have been
ARPHRD_AX25.  We only got away because AF_AX25 and ARPHRD_AX25 both happen
to be defined to the same value.

Don't check sax25_ndigis either; it's value is insignificant for the
purpose of setting the MAC address and the check has shown to break
some application software for no good reason.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

I dropped the timer initialization bits by accident when sending the
p-persistence fix.  This patch gets the driver to work again on halfduplex
links.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Dumb typo: iounmap(&local_pointer_variable).
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The userspace must not be able to issue ethtool command and manage the
mii before it is completely initialized. Avoid some pesky "eth%d" messages.
Signed-off-by: NArnaud Patard <apatard@mandriva.com>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The tg3_abort_hw() call in tg3_test_loopback() is causing lockups on
some devices. tg3_abort_hw() disables the memory arbiter, causing
tg3_reset_hw() to hang when it tries to write the pre-reset signature.
tg3_abort_hw() should only be called after the pre-reset signature has
been written. This is all done in tg3_reset_hw() so the tg3_abort_hw()
call is unnecessary and can be removed.

[ Also bump driver version and release date. -DaveM ]
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver version, white space, comments & other
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NGanesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Add cpu cycle saver microcode to 8086:{1209/1229} other than ICH devices.
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NGanesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Increased delay loop for command blocks
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NGanesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fixed endian bug associated with cb_i bit in xmit_prepare
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NGanesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

added msleep_interruptible delay right before returning from diag_test
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NGanesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Do not check Rx packet length against mtu - patch from Darren Tucker
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NGanesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

netpoll is void(struct net_device *), not int(struct net_device *)
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

emac doesn't build modular; ibm_emac_debug doesn't build at all (missing
headers).
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

airo_cs is broken on m32r; marked as such. [Proper fix would involve
separating PCI-dependent parts and making sure they don't get in the
way _and_ arranging for asm/scatterlist.h getting picked on m32r]
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

ISA parts of tms380tr are using ISA DMA helpers and should depend on
ISA_DMA_API.
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This change allows a bonding device to inherit the "zero-copy"
features of its slave devices.

It was inspired by a couple of previous postings on this topic:
http://marc.theaimsgroup.com/?l=bonding-devel&m=111924607327794&w=2
http://marc.theaimsgroup.com/?l=bonding-devel&m=111925242706297&w=2
and it's largely a combination of the patches that appear in those
emails.
Signed-off-by: NArthur Kepner <akepner@sgi.com>

The purpose of this patch:

- Adopt the DMA API (jazzsonic, macsonic & core driver).

- Adopt the driver model (macsonic).

This part was cribbed from jazzsonic. As a consequence, macsonic once
again works as a module. Driver model is also used by the DMA calls.

- Support 16 bit cards (macsonic & core driver, also affects jazzsonic)

This code was adapted from the mac68k linux 2.2 kernel, where it has
languished for a long time.

- Support more 32-bit mac cards (macsonic)

Also from mac68k repo.

- Zero-copy buffer handling (core driver)

Provides a nice performance improvement. The new algorithm incidentally
helped to replace the old Jazz DMA code.

The patch was tested on a variety of macs (several 32-bit quadra built-in
NICs, a 16-bit LC PDS NIC and a 16-bit comm-slot NIC), and also on MIPS
Jazz.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

[PATCH] [NET] mv643xx: add workaround for HW checksum generation bug

The hardware checksum generator on the mv64xxx occasionally generates
an incorrect checksum.  This patch works around the issue and enables
hardware checksum generation.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>