This patch adds to ioatdma and dca modules
support for Intel I/OAT DMA engine ver.3 (aka CB3 device).
The main features of I/OAT ver.3 are:
 * 8 single channel DMA devices (8 channels total)
 * 8 DCA providers, each can accept 2 requesters
 * 8-bit TAG values and 32-bit extended APIC IDs
Signed-off-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

I/OAT DMA performance tuning showed different optimal values of
tcp_dma_copybreak for different I/OAT versions (4096 for 1.2 and 2048
for 2.0).  This patch lets ioatdma driver set tcp_dma_copybreak value
according to these results.

[dan.j.williams@intel.com: remove some ifdefs]
Signed-off-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Due to occasional DMA channel hangs observed for I/OAT versions 1.2 and 2.0
a watchdog has been introduced to check every 2 seconds
if all channels progress normally.
If stuck channel is detected, driver resets it.
The reset is done in two parts. The second part is scheduled
by the first one to reinitialize the channel after the restart.
Signed-off-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Force callers that trigger an "out of descriptors" condition to run the
cleanup loop directly.  Alleviates the requirement to have soft-irqs
enabled when polling for a descriptor in async_xor.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

This adds a driver for the Synopsys DesignWare DMA controller (aka
DMACA on AVR32 systems.) This DMA controller can be found integrated
on the AT32AP7000 chip and is primarily meant for peripheral DMA
transfer, but can also be used for memory-to-memory transfers.

This patch is based on a driver from David Brownell which was based on
an older version of the DMA Engine framework. It also implements the
proposed extensions to the DMA Engine API for slave DMA operations.

The dmatest client shows no problems, but there may still be room for
improvement performance-wise. DMA slave transfer performance is
definitely "good enough"; reading 100 MiB from an SD card running at ~20
MHz yields ~7.2 MiB/s average transfer rate.

Full documentation for this controller can be found in the Synopsys
DW AHB DMAC Databook:

http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf

The controller has lots of implementation options, so it's usually a
good idea to check the data sheet of the chip it's intergrated on as
well. The AT32AP7000 data sheet can be found here:

http://www.atmel.com/dyn/products/datasheets.asp?family_id=682


Changes since v4:
  * Use client_count instead of dma_chan_is_in_use()
  * Add missing include
  * Unmap buffers unless client told us not to

Changes since v3:
  * Update to latest DMA engine and DMA slave APIs
  * Embed the hw descriptor into the sw descriptor
  * Clean up and update MODULE_DESCRIPTION, copyright date, etc.

Changes since v2:
  * Dequeue all pending transfers in terminate_all()
  * Rename dw_dmac.h -> dw_dmac_regs.h
  * Define and use controller-specific dma_slave data
  * Fix up a few outdated comments
  * Define hardware registers as structs (doesn't generate better
    code, unfortunately, but it looks nicer.)
  * Get number of channels from platform_data instead of hardcoding it
    based on CONFIG_WHATEVER_CPU.
  * Give slave clients exclusive access to the channel

Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>,
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

This patch adds the necessary interfaces to the DMA Engine framework
to use functionality found on most embedded DMA controllers: DMA from
and to I/O registers with hardware handshaking.

In this context, hardware hanshaking means that the peripheral that
owns the I/O registers in question is able to tell the DMA controller
when more data is available for reading, or when there is room for
more data to be written. This usually happens internally on the chip,
but these signals may also be exported outside the chip for things
like IDE DMA, etc.

A new struct dma_slave is introduced. This contains information that
the DMA engine driver needs to set up slave transfers to and from a
slave device. Most engines supporting DMA slave transfers will want to
extend this structure with controller-specific parameters.  This
additional information is usually passed from the platform/board code
through the client driver.

A "slave" pointer is added to the dma_client struct. This must point
to a valid dma_slave structure iff the DMA_SLAVE capability is
requested.  The DMA engine driver may use this information in its
device_alloc_chan_resources hook to configure the DMA controller for
slave transfers from and to the given slave device.

A new operation for preparing slave DMA transfers is added to struct
dma_device. This takes a scatterlist and returns a single descriptor
representing the whole transfer.

Another new operation for terminating all pending transfers is added as
well. The latter is needed because there may be errors outside the scope
of the DMA Engine framework that may require DMA operations to be
terminated prematurely.

DMA Engine drivers may extend the dma_device, dma_chan and/or
dma_slave_descriptor structures to allow controller-specific
operations. The client driver can detect such extensions by looking at
the DMA Engine's struct device, or it can request a specific DMA
Engine device by setting the dma_dev field in struct dma_slave.

dmaslave interface changes since v4:
  * Fix checkpatch errors
  * Fix changelog (there are no slave descriptors anymore)

dmaslave interface changes since v3:
  * Use dma_data_direction instead of a new enum
  * Submit slave transfers as scatterlists
  * Remove the DMA slave descriptor struct

dmaslave interface changes since v2:
  * Add a dma_dev field to struct dma_slave. If set, the client can
    only be bound to the DMA controller that corresponds to this
    device.  This allows controller-specific extensions of the
    dma_slave structure; if the device matches, the controller may
    safely assume its extensions are present.
  * Move reg_width into struct dma_slave as there are currently no
    users that need to be able to set the width on a per-transfer
    basis.

dmaslave interface changes since v1:
  * Drop the set_direction and set_width descriptor hooks. Pass the
    direction and width to the prep function instead.
  * Declare a dma_slave struct with fixed information about a slave,
    i.e. register addresses, handshake interfaces and such.
  * Add pointer to a dma_slave struct to dma_client. Can be NULL if
    the DMA_SLAVE capability isn't requested.
  * Drop the set_slave device hook since the alloc_chan_resources hook
    now has enough information to set up the channel for slave
    transfers.
Acked-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

In some cases client code may need the dma-driver to skip the unmap of source
and/or destination buffers.  Setting these flags indicates to the driver to
skip the unmap step.  In this regard async_xor is currently broken in that it
allows the destination buffer to be unmapped while an operation is still in
progress, i.e. when the number of sources exceeds the hardware channel's
maximum (fixed in a subsequent patch).
Acked-by: NSaeed Bishara <saeed@marvell.com>
Acked-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

A DMA controller capable of doing slave transfers may need to know a
few things about the slave when preparing the channel. We don't want
to add this information to struct dma_channel since the channel hasn't
yet been bound to a client at this point.

Instead, pass a reference to the client requesting the channel to the
driver's device_alloc_chan_resources hook so that it can pick the
necessary information from the dma_client struct by itself.

[dan.j.williams@intel.com: fixed up fsldma and mv_xor]
Acked-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

This client tests DMA memcpy using various lengths and various offsets
into the source and destination buffers. It will initialize both
buffers with a repeatable pattern and verify that the DMA engine copies
the requested region and nothing more. It will also verify that the
bytes aren't swapped around, and that the source buffer isn't modified.

The dmatest module can be configured to test a specific device, a
specific channel. It can also test multiple channels at the same time,
and it can start multiple threads competing for the same channel.

Changes since v2:
  * Support testing multiple channels at the same time
  * Support testing with multiple threads competing for the same channel
  * Use counting test patterns in order to catch byte ordering issues

Changes since v1:
  * Remove extra dashes around "help"
  * Remove "default n" from Kconfig
  * Turn TEST_BUF_SIZE into a module parameter
  * Return DMA_NAK instead of DMA_DUP
  * Print unhandled events
  * Support testing specific channels and devices
  * Move to the end of the Makefile
Acked-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The XOR engine found in Marvell's SoCs and system controllers
provides XOR and DMA operation, iSCSI CRC32C calculation, memory
initialization, and memory ECC error cleanup operation support.

This driver implements the DMA engine API and supports the following
capabilities:
- memcpy
- xor
- memset

The XOR engine can be used by DMA engine clients implemented in the
kernel, one of those clients is the RAID module.  In that case, I
observed 20% improvement in the raid5 write throughput, and 40%
decrease in the CPU utilization when doing array construction, those
results obtained on an 5182 running at 500Mhz.

When enabling the NET DMA client, the performance decreased, so
meanwhile it is recommended to keep this client off.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Acked-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Since 43cc71ee, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to most
of the hotpluggable platform drivers, to re-enable auto loading.

Cc: <stable@kernel.org>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Haavard's dma-slave interface would like to test for exclusive access to a
channel.  The standard channel refcounting is not sufficient in that it
tracks more than just client references, it is also inaccurate as reference
counts are percpu until the channel is removed.

This change also enables a future fix to deallocate resources when a client
declines to use a capable channel.
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The dependency is redundant since all drivers set their specific arch
dependencies.  The NET_DMA option is modified to be enabled only on platforms
where it is known to have a positive effect.  HAS_DMA is added as an explicit
dependency for the DMADEVICES menu.
Acked-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Set the 'parent' field of channel class devices to point to the
physical DMA device initialized by the DMA engine driver.

This allows drivers to use chan->dev.parent for syncing DMA buffers
and adds a 'device' symlink to the real device in
/sys/class/dma/dmaXchanY.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Signed-off-by: NLi Yang <leoli@freescale.com>
Acked-by: NZhang Wei <zw@zh-kernel.org>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The pciehp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fix the following errors reported by Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.

kobject_add_internal failed for 2 with -EEXIST, don't try to register things with the same name in the same directory.
Pid: 1, comm: swapper Tainted: G        W 2.6.26-rc3 #1
 [<c0266980>] kobject_add_internal+0x140/0x190
 [<c0266afd>] kobject_init_and_add+0x2d/0x40
 [<c027bc91>] pci_hp_register+0x81/0x2f0
 [<c027fd07>] pciehp_probe+0x1a7/0x470
 [<c01b3b84>] sysfs_add_one+0x44/0xa0
 [<c01b3c1f>] sysfs_addrm_start+0x3f/0xb0
 [<c01b497a>] sysfs_create_link+0x8a/0xf0
 [<c0279570>] pcie_port_probe_service+0x50/0x80
 [<c02e0545>] driver_sysfs_add+0x55/0x70
 [<c02e0662>] driver_probe_device+0x82/0x180
 [<c02e07cc>] __driver_attach+0x6c/0x70
 [<c02dfe0a>] bus_for_each_dev+0x3a/0x60
 [<c05db2d0>] pcied_init+0x0/0x80
 [<c02e04e6>] driver_attach+0x16/0x20
 [<c02e0760>] __driver_attach+0x0/0x70
 [<c02e0341>] bus_add_driver+0x1a1/0x220
 [<c05db2d0>] pcied_init+0x0/0x80
 [<c02e09cd>] driver_register+0x4d/0x120
 [<c05db050>] ibm_acpiphp_init+0x0/0x190
 [<c0125aab>] printk+0x1b/0x20
 [<c05db2d0>] pcied_init+0x0/0x80
 [<c05db2de>] pcied_init+0xe/0x80
 [<c05c751a>] kernel_init+0x10a/0x300
 [<c0120138>] schedule_tail+0x18/0x50
 [<c0103b9a>] ret_from_fork+0x6/0x1c
 [<c05c7410>] kernel_init+0x0/0x300
 [<c05c7410>] kernel_init+0x0/0x300
 [<c010485b>] kernel_thread_helper+0x7/0x1c
 =======================
pci_hotplug: Unable to register kobject '2'<3>pciehp: pci_hp_register failed with error -22

Slot with the same name can be registered multiple times if shpchp or
pciehp driver is loaded after acpiphp is loaded because ACPI based
hotplug driver and Native OS hotplug driver trying to handle the same
physical slot. In this case, current pci_hotplug core will call
kobject_init_and_add() muliple time with the same name. This is the
cause of this problem. To fix this problem, this patch adds the check
into pci_hp_register() to see if the slot with the same name.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

According to the PCI Express specification, we must wait for at least
1 second after turning power off before taking any action that relies
on power having been removed from the slot/adapter. For this, current
pciehp wait for 1 second after issuing the power off command in
hpc_power_off_slot() function. But waiting for 1 second in
hpc_power_off_slot() can make pciehp probing slow-down because pciehp
probe code calls hpc_power_off_slot() if the slot is not occupied just
in case. We don't need to wait for 1 second at the pciehp probe time
because there is no action on that empty slot. So move 1 second wait
from hpc_power_off_slot() to the caller of hpc_power_off_slot().
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fix improper long wait for command completion in pciehp probing.

As described in PCI Express specification, software notification is
not generated if the command that occurs as a result of a write to the
Slot Control register that disables software notification of command
completed events. Since pciehp driver doesn't take it into account,
such command is issued in pciehp probing, and it causes improper long
wait for command completion.

This patch changes the pciehp driver to take such command into
account.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fix the "pciehp probing slow" problem reported from Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.

The command completed bit in Slot Status register applies only to
commands issued to control the attention indicator, power indicator,
power controller, or electromechanical interlock. However, writes to
other parts of the Slot Control register would end up writing to the
control fields. Hence, any write to Slot Control register is
considered as a command. However, if the controller doesn't support
any of attention indicator, power indicator, power controller and
electromechanical interlock, command completed bit would not set in
writing to Slot Control register. In this case, we should not wait for
command completed bit set, otherwise all commands would be considered
not completed in timeout seconds (1 sec.).

The cause of the problem is pciehp driver didn't take this situation
into account. This patch changes pciehp to take it into account. This
patch also add the check for "No Command Completed Support" bit in
Slot Capability register. If it is set, we should not wait for command
completed bit set as well.

This problem seems to be revealed by the commit
c27fb883 that fixed the bug that
pciehp did not wait for command completed properly (pciehp just
ignored the command completion event).
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fix the following NULL dereference problem reported from Pierre Ossman
and Ingo Molnar.

pciehp: HPC vendor_id 8086 device_id 27d0 ss_vid 0 ss_did 0
pciehp: pciehp_find_slot: slot (device=0x0) not found
BUG: unable to handle kernel NULL pointer dereference at 0000000000000070
IP: [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
PGD 0
Oops: 0000 [1]
CPU 0
Modules linked in:
Pid: 1, comm: swapper Tainted: G        W 2.6.26-rc3-sched-devel.git-00001-g2b99b26-dirty #170
RIP: 0010:[<ffffffff80494a8b>]  [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
RSP: 0000:ffff81003f83fbb0  EFLAGS: 00010046
RAX: 0000000000000039 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000046
RBP: ffff81003f83fbd0 R08: 0000000000000001 R09: ffffffff80245103
R10: 0000000000000020 R11: 0000000000000000 R12: ffff81003ea53a30
R13: 0000000000000000 R14: 0000000000000011 R15: ffffffff80495926
FS:  0000000000000000(0000) GS:ffffffff80be7400(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000070 CR3: 0000000000201000 CR4: 00000000000006a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 1, threadinfo ffff81003f83e000, task ffff81003f840000)
Stack:  0000000000000008 ffff81003f83fbf6 ffff81003ea53a30 0000000000000008
 ffff81003f83fc10 ffffffff80495ab4 0000000000000011 0000000000000002
 0000000000000202 0000000000000202 00000000fffffff4 ffff81003ea53a30
Call Trace:
 [<ffffffff80495ab4>] pcie_isr+0x18e/0x1bc
 [<ffffffff80260831>] request_irq+0x106/0x12f
 [<ffffffff80495fb6>] pcie_init+0x15e/0x6cc
 [<ffffffff804933a3>] pciehp_probe+0x64/0x541
 [<ffffffff8048f4e7>] pcie_port_probe_service+0x4c/0x76
 [<ffffffff8054af70>] driver_probe_device+0xd4/0x1f0
 [<ffffffff8054b108>] __driver_attach+0x7c/0x7e
 [<ffffffff8054b08c>] ? __driver_attach+0x0/0x7e
 [<ffffffff8054a4b6>] bus_for_each_dev+0x53/0x7d
 [<ffffffff8054ad3c>] driver_attach+0x1c/0x1e
 [<ffffffff8054a9c2>] bus_add_driver+0xdd/0x25b
 [<ffffffff80c09d3d>] ? pcied_init+0x0/0x8b
 [<ffffffff8054b288>] driver_register+0x5f/0x13e
 [<ffffffff80c09d3d>] ? pcied_init+0x0/0x8b
 [<ffffffff8048f441>] pcie_port_service_register+0x47/0x49
 [<ffffffff80c09d52>] pcied_init+0x15/0x8b
 [<ffffffff80bf3938>] kernel_init+0x75/0x243
 [<ffffffff808639d2>] ? _spin_unlock_irq+0x2b/0x3a
 [<ffffffff80228d1f>] ? finish_task_switch+0x57/0x9a
 [<ffffffff8020c258>] child_rip+0xa/0x12
 [<ffffffff8020bcec>] ? restore_args+0x0/0x30
 [<ffffffff80bf38c3>] ? kernel_init+0x0/0x243
 [<ffffffff8020c24e>] ? child_rip+0x0/0x12

Code: 83 80 00 00 00 48 39 f0 75 e1 0f b6 c9 48 c7 c2 00 0e 8d 80 48 c7 c6 8a 60 a6 80 48 c7 c7 10 db a8 80 31 c0 e8 3f 8d d9 ff 31 db <48> 8b 43 70 48 8d 75 ef 48 89 df ff 50 30 80 7d ef 00 74 37 48
RIP  [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
 RSP <ffff81003f83fbb0>
CR2: 0000000000000070
Kernel panic - not syncing: Fatal exception

The situation under which it occurs is hw and timing related: it appears
to happen on a system that has PCI hotplug hardware but with no active
hotplug cards, and another interrupt in the same (shared) IRQ line
arrives too early, before the hotplug-slot entry has been set up - as
triggered by CONFIG_DEBUG_SHIRQ=y:

This patch contains the following two fixes.

(1) Clear all events bits in Slot Status register to prevent the pciehp
    driver from detecting the spurious events that would have been occur
    before pciehp loading.

(2) Add check whether slot initialization had been already done.

This is short term fix. We need more structural fixes to install
interrupt handler after slot initialization is done.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The shpchp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

There's a reason why using C99 initialisers even in the supposedly
trivial structs is a good idea.
Signed-off-by: NCarl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The tuner driver used to change i2c_client.name for its own needs, but
it really shouldn't, as this field is used by i2c-core to do the
device/driver matching. So, create and use a separate field for the
tuner driver needs.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add the Intel ICH9DO controller ID's for the iTCO_wdt kernel driver and bump
the driver version.

Tested on an P5E-VM DO ASUS motherboard.
Signed-off-by: NGabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

On Book-E SMP systems each core has its own private watchdog.  If only one
watchdog is enabled, when the core that doesn't enable the watchdog is hung,
system can't reset because no watchdog is running on it.  That's bad.  It
means we must enable watchdogs on both cores.

We can use smp_call_function() to send appropriate messages to all the other
cores to enable and update the watchdog.
Signed-off-by: NChen Gong <g.chen@freescale.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

Add a watchdog timer based on the MFGPT timers in the CS5535/CS5536
companion chips to the AMD Geode GX and LX processors.  Only caveat
is that the BIOS must provide at least a one free timer, and most
do not.
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

I need to just return in case it's not my NMI so someone else can take a look
at it (and reset die_nmi_called to 0 in case I actually do get one that's mine
to handle).
Signed-off-by: NThomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

 - split platform device/driver registering from actual watchdog device/driver
   registering so that we can cleanly load/unload
 - fixup __initdata with __initconst and __devinitdata with __devinitconst
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Pádraig Brady requested the possibility of not disabling the watchdog
at module load time or kernel boot time if it had been previously enabled
in the bios. It may help rebooting the machine if it freezes before the
userland daemon kicks in.
Signed-off-by: NSamuel Tardieu <sam@rfc1149.net>
Cc: Pádraig Brady <P@draigBrady.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Signed-off-by: NSamuel Tardieu <sam@rfc1149.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Some non-exported functions always returned 0. Mark them void instead.
Signed-off-by: NSamuel Tardieu <sam@rfc1149.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Somehow the spidev code forgot to include a critical mechanism: when the
underlying device is removed (e.g.  spi_master rmmod), open file
descriptors must be prevented from issuing new I/O requests to that
device.  On penalty of the oopsing reported by Sebastian Siewior
<bigeasy@tglx.de> ...

This is a partial fix, adding handshaking between the lower level (SPI
messaging) and the file operations using the spi_dev.  (It also fixes an
issue where reads and writes didn't return the number of bytes sent or
received.)

There's still a refcounting issue to be addressed (separately).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Reported-by: NSebastian Siewior <bigeasy@tglx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

including of <asm/mpc85xx.h> causes build problems since it doesn't exist.

Also removed warning:
drivers/edac/mpc85xx_edac.c:45: warning: 'mpc85xx_ctl_name' defined but not used
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NDoug Thompson <dougthompson@xmission.com>
Acked-by: NDave Jiang <djiang@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a correct MODULE_ALIAS() entry for this driver to enable udev module
loading.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the old changelog entries which are now out of date and should be
extractable from git anyway.  Also tidy up the copyright for the driver.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following warning by checking the result of device_create_file and
printing an error but not removing the device (loss of debug registers is
not fatal).

drivers/video/s3c2410fb.c:905: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a blank level of FB_BLANK_POWERDOWN is used, we should shut down the
controller so that it no longer tries to produce any panel signals or
data, and shuts down the DMA which is not needed.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

To keep backwards compatibility, reverse the meanings of these flags so
that when they are not set, the driver uses the original behvaiour.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>