when the BE device becomes unresponsive, dump the registers to help debugging
Signed-off-by: NSomnath K <somnathk@serverengines.com>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move be_check_sriov_fn_type to appropriate place to correctly determine
if the be2net driver needs to work as a VF driver or a PF driver.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes names of some variables.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a mac address has not been configured for a VF,
there is no need to call be_cmd_pmac_del.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When driver is loaded in guest OS, the pci variables is_virtfn and is_physfn are
both set to 0. This change uses registers in controller to determine the same.
Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ibm p7 architecure seems to reorder memory accesses more
aggressively than previous ppc64 architectures. This requires memory
barriers to ensure that rx/tx doorbells are pressed only after
memory to be DMAed is written.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ipv6 support to the be2net driver.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds cleanup code (things like unregistering irq,
disabling napi etc) to be_open() when an error occurs inside the
routine.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Certain firmware commands/operations to upgrade firmware could take several
seconds to complete. The code presently disables bottom half during these
operations which could lead to unpredictable behaviour in certain cases. This
patch now does all firmware upgrade operations asynchronously using a
completion variable.
Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCI function reset needs to invoked after fw init ioctl is issued.
Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.

It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.

It also does not remove null void functions with return.

Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
  xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'

with some cleanups by hand.

Compile tested x86 allmodconfig only.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replaces (skb->len - skb->data_len) occurrences by skb_headlen(skb)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

benet driver wrongly assumes that zero is an invalid dma address
(calls dma_unmap_page for only non zero dma addresses). Zero is a
valid dma address on some architectures. The dma length can be used
here.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DMA API is preferred.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Patch adds support to enable PCI SRIOV in the driver and changes to handle initialization of PCI virtual functions.
- Function handler to change mac addresses for VF from its corresponding PF.
Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vlan traffic on big endian architecture is broken.
Need to swap the vid before giving packet to stack.
This patch fixes it.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flashing is broken on big endian architectures like ppc.
This patch fixes it.

From: Naresh G <nareshg@serverengines.com>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

eth_type_trans(skb, netdev) does the "skb->dev = netdev;"
initialization, we can remove it from various network drivers.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first wrb seen by tx compl processing does not have a dma handle in it.
Currently, pci_unmap_single() is attempted on this wrb and pci_unmap_page() on the
rest. So, pci_unmap_page() gets incorrectly called on the dma hdl of skb->data (that
was mapped using map_single()). This patch fixes this issue.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleans up some unused code from be_load_fw().
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PCI functions are virtuialized in applications by assigning PCI
functions to VM (PCI passthrough), the be2net driver in the VM sees a

different function number. So, use of PCI function number in any
calculation will break existing code. This patch takes care of it.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding code to update NCSI section while updating firmware on the controller.
Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In tx/mcc polling, napi_complete() is being incorrectly called
before reaping tx completions. This can cause tx compl processing
to be scheduled on another cpu concurrently which can result in a panic.
This if fixed by calling napi complete() after tx/mcc compl processing
but before re-enabling interrupts (via a cq notify).
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For certain skews of the BE adapter, H/W Tx and Rx
counters could be common for more than one interface.
Add Tx and Rx counters in the adapter structure
(to maintain stats on a per interfae basis).
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be2net: free tx buffers when completions never arrive

In cases like when a pci device is disconnected on an error,
pending tx completions will never arrive. Unmap and free such
buffers in the tx cleanup path.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flush compl (compl with numfrags == 0; no data) is rcvd
from hw to indicate completion of RXQ destory operation. Fix
the RX path to not process it as RX data.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an MCC cmd is issued (via a netdev/ethtool op)
while the device is not open, the MCC CQ gets processed but the EQ
is not processed (as isr is not registered.) This can cause the EQ
to become full. So, while the device is not open, CQ must not be re-armed
to prevent EQ entries.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce unlikely() for skb alloc failure and vlanf checks...
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code has been tested on IBM pSeries server.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In certain skews the ASIC can support only 16 vlans per interface.
Once the limit is crossed, the ASIC is programmed in vlan promiscuous mode.
Switch off the vlan promiscuous mode once the number of vlans
falls back to the max vlans supported.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>