This implements the pin configuration interface for the
Nomadik pin controller.

As part of the exercise we add a bit in the pin_cfg_t for
the Nomadik pinctrl driver that indicates if the pin should
be forced into GPIO mode. This is not done to go behind the
back of the GPIO subsystem, but to ensure that default modes
can be set by hogs on boot and system suspend/resume states.
It was used implicitly by the old code defining all config
settings and modes in a single config word but we now have
a split between pinmux and pinconf leading to the need to
have this.

We also add a bit for explicitly setting sleepmode of the
pin. This was previously handled by custom calls with the
_sleep() suffix, but we now have one single interface into
the configuration so we replace this with a bit indicating
that the pin shall be configured into sleep mode.

Some of the configuration can be refactored later to use
less custom fields on the pin_cfg_t but we are currently
leaving the old function calls in place so we stay
compatible.

ChangeLog v1->v2:
- Drop a hunk changing pinmuxing for GPIO and move it
  over to the preceding pinmux patch.
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds a few sleep mode pin config macros for sleep mode
for the Nomadik GPIO/pin controller.
Signed-off-by: NRickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: NRikard Olsson <rikard.p.olsson@stericsson.com>
Signed-off-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Low EMI (Electro-Magnetic Interference) mode means lower slew
rate on the signals. The Nomadik GPIO controller supports
this so create an interface to enable it.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

All sched_clock() providers have been converted to the sched_clock
framework, which also provides a jiffy based implementation for
the platforms that do not provide a counter.

It is now possible to make the sched_clock framework mandatory,
effectively preventing new platforms to add new sched_clock()
functions, which would be detrimental to the single zImage work.
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Modernize the MTU timer to rely on the clockevents core to
calculate mult and shift and setup the clock event.
Acked-by: NAlessandro Rubini <rubini@unipv.it>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

clk_prepare() was missing from the Nomadik MTU driver, also handle
errors on prepare and enable in the simplest way possible, by
bugging out - we cannot start the system without time anyway.
Acked-by: NAlessandro Rubini <rubini@unipv.it>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Pass the base offset to the Nomadik MTU timer in the init call
instead of keeping a global pointer to be assigned.
Acked-by: NAlessandro Rubini <rubini@unipv.it>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

sched_clock() is yet another blocker on the road to the single
image. This patch implements an idea by Russell King:

http://www.spinics.net/lists/linux-omap/msg49561.html

Instead of asking the platform to implement both sched_clock()
itself and the rollover callback, simply register a read()
function, and let the ARM code care about sched_clock() itself,
the conversion to ns and the rollover. sched_clock() uses
this read() function as an indirection to the platform code.
If the platform doesn't provide a read(), the code falls back
to the jiffy counter (just like the default sched_clock).

This allow some simplifications and possibly some footprint gain
when multiple platforms are compiled in. Among the drawbacks,
the removal of the *_fixed_sched_clock optimization which could
negatively impact some platforms (sa1100, tegra, versatile
and omap).

Tested on 11MPCore, OMAP4 and Tegra.

Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Tested-by: NJamie Iles <jamie@jamieiles.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Tested-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NKrzysztof Halasa <khc@pm.waw.pl>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Allow logical channels to specify the physical channel they want to use.
This is needed to avoid two peripherals operating on the same physical
channel during some special use-cases. (like mmc and usb during a
usb mass storage case).
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NNarayanan G <narayanan.gopalakrishnan@stericsson.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

This patch provides an option of having the lcla (link address)
in ESRAM instead of allocating it. The bool value (use_esram_lcla)
in the stedma40_platform_data if set to true, then the lcla
address would be taken from platform resources. Also, the
corresponding esram regulator is managed in the
suspend/resume functions.
Signed-off-by: NNarayanan G <narayanan.gopalakrishnan@stericsson.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves dma/drivers/* to use new enum

Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: H Hartley Sweeten <hartleys@visionengravers.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Zhang Wei <zw@zh-kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Yong Wang <yong.y.wang@intel.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Cc: Boojin Kim <boojin.kim@samsung.com>
Cc: Barry Song <Baohua.Song@csr.com>
Acked-by: NMika Westerberg <mika.westerberg@iki.fi>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

We make the reset function from the driver public, then
we also move of all register defines from the public header
file into driver, where they belong.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds support for a periodic mode in the MTU (Nomadik)
timer clockevent driver. It also include changes needed for
deeper powerstates where MTU block gets powered off.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch makes it possible to configure away the sched_clock
part of the MTU timer.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NMattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: NJonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The GPIO clock is required for register access and interrupt detection.
When interrupt detection is not required on any of the pin in a block,
the block's clock can be disabled when the registers are not being
accessed.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NRickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: NJonas Aberg <jonas.aberg@stericsson.com>
[Adjust for new IRQ chip core code, use only local functions]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Remove PIN_CFG_PULL in pincfg.h for plat-nomadik, PIN_CFG_INPUT
already takes care of this. Added support for SPI2.
Signed-off-by: NFredrik Svensson <fredrik.xk.svensson@stericsson.com>
Signed-off-by: NDaniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

After recent consolidations the Nomadik <plat/gpio.h> is entirely
superfluous, so get rid of it.
Reported-by: NRussell King <linux@arm.linux.org.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The <[plat|mach]/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.

Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than marking the mach/gpio.h header files which want to use the
trivial GPIOLIB implementation, mark those which do not want to use it
instead.  This means that by default, you get the trivial implementation
and only have to do something extra if you need to.  This should
encourage the use of the trivial default implementation.

As an additional bonus, several gpio.h header files become empty.
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Many of the gpio_to_irq implementations use the gpiolib version of this
function.  Provide the standard gpiolib gpio_to_irq() for everyone, but
allow platforms to override it if they wish.  Add the neccessary
overrides for those platforms which do not use the standard definition.
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Consolidate 24 trivial gpiolib implementions out of mach/gpio.h
into asm/gpio.h.  This is basically the include of asm-generic/gpio.h
and the definition of gpio_get_value, gpio_set_value, and gpio_cansleep
as described in Documentation/gpio.txt
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: NDavid Brown <davidb@codeaurora.org>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).

To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.

Hope people are OK with tiny include file.

Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.
Reported-by: NAxel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NRickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: NMartin Persson <martin.persson@stericsson.com>
[Split off from larger patch]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This moves the Nomadik GPIO driver out of arch/arm/plat-nomadik
and into the desired location indicated by the subsystem
maintainer.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
[grant.likely: squashed with kconfig fixup]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The I2C speed enumerators in the i2c-nomadik header file were in
the wrong order.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add option to have different i2c timeout delay for different i2c buses
specified in platform data. Default to the old value unless specified.
Signed-off-by: NVirupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Convert SP804, MXC, Nomadik and Orion 32-bit down-counting clocksources
to generic mmio clocksource infrastructure.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: NNicolas Pitre <nico@fluxnic.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch updates the Nomadik gpio chained IRQ handler to use the
chained IRQ enter/exit functions in order to function correctly on
primary controllers with different methods of flow control.

Cc: Rabin Vincent <rabin@rab.in>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Use irq_set_chip_and_handler() instead. Converted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Convert to the new function names. Automated with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Store the enabled mask in the local state, so there is no need to
fiddle in the irq descriptor.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

gpiolib plus two gpio implementations in arm fiddle in the guts of
irq_desc in a racy and buggy way. Remove the stuff. I already told the
gpio folks that we can provide that information in a proper way if
necessary.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
LKML-Reference: <20110324212508.931638262@linutronix.de>

Enable wakeups by default for any GPIO interrupts and in the suspend/resume
path narrow this down to only the the real wakeup interrupts. This approach is
based on the assumption that cpuidle ApSleep will be entered more often than
system suspend.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Fixup for genirq changes to struct irq_data on 2.6.38]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The compiler warns that [rf]wimsc may be used uninitialized in
this function - the warning is actually false since the uses are
in identical if()-clauses, but it can't hurt very much to read
out the values to be modified early anyway and rid the warning.

Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The NOMADIK_GPIO_PM config option is disabled by default, not user visible,
and never selected by any other option: the code is therefore unused. The
GPIO registers need not be saved and restored since their values are
preserved when vAPE (on DB8500) is powered down.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NJonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch fixes a bug when setting SLPM register for DB8500.
When calling__nmk_gpio_set_slpm(...) offset to GPIO is now used
instead of the GPIO number itself.
Signed-off-by: NRikard Olsson <rikard.p.olsson@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Setting pinmux alternative C for a GPIO pin is actually not
so easy since it ivolves setting value "1" in two registers,
and since the combined result will take effect for intermediate
values (01 or 10) this will cause glitches while you wrote one
register but have not yet written the other.

This patch implements a series of kludges including an optional
machine-specific callback to avoid glitches when changing pin
mux mode to alternative C.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>