If a URB is killed while the host is removed we can end up in a situation
where the hub thread takes the roothub device lock, and waits for
the URB to be given back by xhci-hcd, blocking the host remove code.

xhci-hcd tries to stop the endpoint and give back the urb, but can't
as the host is removed from PCI bus at the same time, preventing the normal
way of giving back urb.

Instead we need to rely on the stop command timeout function to give back
the urb. This xhci_stop_endpoint_command_watchdog() timeout function
used a XHCI_STATE_DYING flag to indicate if the timeout function is already
running, but later this flag has been taking into use in other places to
mark that xhci is dying.

Remove checks for XHCI_STATE_DYING in xhci_urb_dequeue. We are still
checking that reading from pci state does not return 0xffffffff or that
host is not halted before trying to stop the endpoint.

This whole area of stopping endpoints, giving back URBs, and the wathdog
timeout need rework, this fix focuses on solving a specific deadlock
issue that we can then send to stable before any major rework.

Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci_setup_device() should return failure with correct error number
when xhci host has died, removed or halted.

During usb device enumeration, if usb host is not accessible (died,
removed or halted), the hc_driver->address_device() should return
a corresponding error code to usb core. But current xhci driver just
returns success. This misleads usb core to continue the enumeration
by reading the device descriptor, which will result in failure, and
users will get a misleading message like "device descriptor read/8,
error -110".

Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci->slot_id is used for providing a way to pass slot id from the
command completion handler to the function waiting for completion.
It's shared by enumerations of all USB devices connected to an
xhci host. Hence, it's a source for possible races. Since we've
introduced command structure and the command queue to xhci driver.
It's better to move slot_id from xhci_hcd structure to xhci_command
structure. Hence the race source is removed.
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci->addr_dev is used for the completion of both address device
and enable slot commands. It's shared by enumerations of all USB
devices connected to an xhci host. Hence, it's just a source for
possible races. Since we've introduced command structure and the
command queue to xhci driver.  It is time to get rid of addr_dev
and use the completion in the command structure instead.
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

define GET_EP_CTX_STATE() macro to get the endpoint state from a
pointer to a le32 enpoint context structure

No functional changes
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no point in trying to reset the host controller by writing
to its registers if host is removed and registers just return 0xffffffff

bail out and return -ENODEV instead
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The old error message always stated that host was not halted
even after trying a certain time.

Host may fail the halt immediately as well with -ENODEV if device
is removed and returns 0xffffffff.

Use a more generic error message and show return value to know if we
failed with -ETIMEDOUT or -ENODEV
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_endpoint_maxp() is now returning maxpacket
correctly - iow only bits 10:0. We can finaly remove
XHCI's private GET_MAX_PACKET macro.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

All kmalloc-based functions print enough information on failures.
Signed-off-by: NWolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We now have implicit batching in the timer wheel. The slack API is no longer
used, so remove it.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094342.189813118@linutronix.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

If the last trb before a link is not packet size aligned, and is not
splittable then use a bounce buffer for that chunk of max packet size
unalignable data.

Allocate a max packet size bounce buffer for every segment of a bulk
endpoint ring at the same time as allocating the ring.
If we need to align the data before the link trb in that segment then
copy the data to the segment bounce buffer, dma map it, and enqueue it.
Once the td finishes, or is cancelled, unmap it.

For in transfers we need to first map the bounce buffer, then queue it,
after it finishes, copy the bounce buffer to the original sg list, and
finally unmap it
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b1c127ae ("usb: host: xhci: plat: make use of new methods in
xhci_plat_priv") sets xhci->quirks before calling xhci_gen_setup(), which
will overwrite them.

Don't overwite the quirks, just add the new ones

Fixes: b1c127ae ("usb: host: xhci: plat: make use of new methods in xhci_plat_priv")
Reported-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Under stress occasions some TI devices might not return early when
reading the status register during the quirk invocation of xhci_irq made
by usb_hcd_pci_remove.  This means that instead of returning, we end up
handling this interruption in the middle of a shutdown.  Since
xhci->event_ring has already been freed in xhci_mem_cleanup, we end up
accessing freed memory, causing the Oops below.

commit 8c24d6d7 ("usb: xhci: stop everything on the first call to
xhci_stop") is the one that changed the instant in which we clean up the
event queue when stopping a device.  Before, we didn't call
xhci_mem_cleanup at the first time xhci_stop is executed (for the shared
HCD), instead, we only did it after the invocation for the primary HCD,
much later at the removal path.  The code flow for this oops looks like
this:

xhci_pci_remove()
	usb_remove_hcd(xhci->shared)
	        xhci_stop(xhci->shared)
 			xhci_halt()
			xhci_mem_cleanup(xhci);  // Free the event_queue
	usb_hcd_pci_remove(primary)
		xhci_irq()  // Access the event_queue if STS_EINT is set. Crash.
		xhci_stop()
			xhci_halt()
			// return early

The fix modifies xhci_stop to only cleanup the xhci data when releasing
the primary HCD.  This way, we still have the event_queue configured
when invoking xhci_irq.  We still halt the device on the first call to
xhci_stop, though.

I could reproduce this issue several times on the mainline kernel by
doing a bind-unbind stress test with a specific storage gadget attached.
I also ran the same test over-night with my patch applied and didn't
observe the issue anymore.

[  113.334124] Unable to handle kernel paging request for data at address 0x00000028
[  113.335514] Faulting instruction address: 0xd00000000d4f767c
[  113.336839] Oops: Kernel access of bad area, sig: 11 [#1]
[  113.338214] SMP NR_CPUS=1024 NUMA PowerNV

[c000000efe47ba90] c000000000720850 usb_hcd_irq+0x50/0x80
[c000000efe47bac0] c00000000073d328 usb_hcd_pci_remove+0x68/0x1f0
[c000000efe47bb00] d00000000daf0128 xhci_pci_remove+0x78/0xb0
[xhci_pci]
[c000000efe47bb30] c00000000055cf70 pci_device_remove+0x70/0x110
[c000000efe47bb70] c00000000061c6bc __device_release_driver+0xbc/0x190
[c000000efe47bba0] c00000000061c7d0 device_release_driver+0x40/0x70
[c000000efe47bbd0] c000000000619510 unbind_store+0x120/0x150
[c000000efe47bc20] c0000000006183c4 drv_attr_store+0x64/0xa0
[c000000efe47bc60] c00000000039f1d0 sysfs_kf_write+0x80/0xb0
[c000000efe47bca0] c00000000039e14c kernfs_fop_write+0x18c/0x1f0
[c000000efe47bcf0] c0000000002e962c __vfs_write+0x6c/0x190
[c000000efe47bd90] c0000000002eab40 vfs_write+0xc0/0x200
[c000000efe47bde0] c0000000002ec85c SyS_write+0x6c/0x110
[c000000efe47be30] c000000000009260 system_call+0x38/0x108
Signed-off-by: NGabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: joel@jms.id.au
Cc: stable@vger.kernel.org
Reviewed-by: NRoger Quadros <rogerq@ti.com>
Cc: <stable@vger.kernel.org> #v4.3+
Tested-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove duplicate function xhci_urb_to_transfer_ring from xhci.c.
We have same function in xhci-ring.c.
Signed-off-by: NAlexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.

Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.

For now the flag is only set for PCI connected host controllers.

Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On some xHCI controllers (e.g. R-Car SoCs), the AC64 bit (bit 0) of
HCCPARAMS1 is set to 1. However, the xHCs don't support 64-bit
address memory pointers actually. So, in this case, this driver should
call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in xhci_gen_setup().
Otherwise, the xHCI controller will be died after a usb device is
connected if it runs on above 4GB physical memory environment.

So, this patch adds a new quirk XHCI_NO_64BIT_SUPPORT to resolve
such an issue.

Cc: <stable@vger.kernel.org>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Give USB3 devices a better chance to enumerate at USB 3 speeds if
they are connected to a suspended host.
Solves an issue with NEC uPD720200 host hanging when partially
enumerating a USB3 device as USB2 after host controller runtime resume.

Cc: <stable@vger.kernel.org>
Tested-by: NMike Murdoch <main.haarp@gmail.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci driver frees data for all devices, both usb2 and and usb3 the
first time usb_remove_hcd() is called, including td_list and and xhci_ring
structures.

When usb_remove_hcd() is called a second time for the second xhci bus it
will try to dequeue all pending urbs, and touches td_list which is already
freed for that endpoint.

Cc: <stable@vger.kernel.org>
Reported-by: NJoe Lawrence <joe.lawrence@stratus.com>
Tested-by: NJoe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In most cases the devices with the speed set to USB_SPEED_SUPER_PLUS
are handled like regular SuperSpeed devices.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The module should fail to load.
Signed-off-by: NOliver Neukum <oneukum@suse.com>
CC: stable@kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There some vendor quirks for MTK xhci host controller:
1. It defines some extra SW scheduling parameters for HW
  to minimize the scheduling effort for synchronous and
  interrupt endpoints. The parameters are put into reseved
  DWs of slot context and endpoint context.
2. Its IMODI unit for Interrupter Moderation register is
  8 times as much as that defined in xHCI spec.
3. Its TDS in  Normal TRB defines a number of packets that
  remains to be transferred for a TD after processing all
  Max packets in all previous TRBs.
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: NDaniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: NDaniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch cleanups the hcd private size to suitable size.
The previous code has "sizeof(struct xhci_hcd *)" in xhci_hc_driver
as hcd_priv_size and sizeof(struct xhci_hcd) in xhci_plat_overrides
or xhci_pci_overrides as extra_priv_size. However, the xhci driver
uses a "sizeof(struct xhcd_hcd)" memory space in each hcd
(main_hcd and shared_hcd) actually.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.

Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: NRajmohan Mani <rajmohan.mani@intel.com>
Tested-by: NJoe Lawrence <joe.lawrence@stratus.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This change avoids DMA error in the cases where dma_mask and
coherent_dma_mask of a 32-bit controller get configured as
DMA_BIT_MASK(64) when running on a 64-bit system.
Signed-off-by: NDuc Dang <dhdang@apm.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Set the controller speed to HCD_USB31 to if host hardware supports USB 3.1

For PCI xhci controllers the USB 3.1 support is checked from SBRN bits in
pci config space. Platform controllers will need to set xhci->sbrn == 0x31
to indicate USB 3.1 support before calling xhci_gen_setup().

Also make sure xhci driver works correctly with speed set to HCD_USB31
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci 1.1 capable controllers have a new HCCPARAMS2 registers
with bits indicating support for new xhci 1.1 capabilities.

Also add support for the new xhci 1.1 bits in the config operational
opertational register that used to be reserved
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
[modified and left out parts not related to HCCPARAMS2 -Mathias]
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

During quick plug/removal of OTG adapter during dual-role testing
it can happen that xhci_alloc_device() is called for the newly
detected device after the DRD library has called xhci_stop to
remove the HCD.

If that is the case, just fail early to prevent the following warning.

[  154.732649] hub 4-0:1.0: USB hub found
[  154.742204] hub 4-0:1.0: 1 port detected
[  154.824458] hub 3-0:1.0: state 7 ports 1 chg 0002 evt 0000
[  154.854609] hub 4-0:1.0: state 7 ports 1 chg 0000 evt 0000
[  154.944430] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[  154.951009] xhci-hcd xhci-hcd.0.auto: xhci_setup_device
[  155.038191] xhci-hcd xhci-hcd.0.auto: remove, state 4
[  155.043315] usb usb4: USB disconnect, device number 1
[  155.055270] xhci-hcd xhci-hcd.0.auto: xhci_stop
[  155.060094] xhci-hcd xhci-hcd.0.auto: USB bus 4 deregistered
[  155.066576] xhci-hcd xhci-hcd.0.auto: remove, state 1
[  155.071710] usb usb3: USB disconnect, device number 1
[  155.077124] xhci-hcd xhci-hcd.0.auto: xhci_setup_device
[  155.082389] ------------[ cut here ]------------
[  155.087690] WARNING: CPU: 0 PID: 72 at drivers/usb/host/xhci.c:3800 xhci_setup_device+0x410/0x484 [xhci_hcd]()
[  155.097861] Modules linked in: sd_mod usb_storage scsi_mod usb_f_ss_lb g_zero libcomposite ipv6 xhci_plat_hcd xhci_hcd usbcore dwc3 udc_core evdev ti_am335x_adc joydev kfifo_buf industrialio snd_soc_simple_cc
[  155.146734] CPU: 0 PID: 72 Comm: kworker/0:3 Tainted: G        W       4.1.4-00834-gcd9380b-dirty #50
[  155.156073] Hardware name: Generic AM43 (Flattened Device Tree)
[  155.162117] Workqueue: usb_hub_wq hub_event [usbcore]
[  155.167249] Backtrace:
[  155.169751] [<c0012af0>] (dump_backtrace) from [<c0012c8c>] (show_stack+0x18/0x1c)
[  155.177390]  r6:c089d4a4 r5:ffffffff r4:00000000 r3:ee46c000
[  155.183137] [<c0012c74>] (show_stack) from [<c05f7c14>] (dump_stack+0x84/0xd0)
[  155.190446] [<c05f7b90>] (dump_stack) from [<c00439ac>] (warn_slowpath_common+0x80/0xbc)
[  155.198605]  r7:00000009 r6:00000ed8 r5:bf27eb70 r4:00000000
[  155.204348] [<c004392c>] (warn_slowpath_common) from [<c0043a0c>] (warn_slowpath_null+0x24/0x2c)
[  155.213202]  r8:ee49f000 r7:ee7c0004 r6:00000000 r5:ee7c0158 r4:ee7c0000
[  155.220051] [<c00439e8>] (warn_slowpath_null) from [<bf27eb70>] (xhci_setup_device+0x410/0x484 [xhci_hcd])
[  155.229816] [<bf27e760>] (xhci_setup_device [xhci_hcd]) from [<bf27ec10>] (xhci_address_device+0x14/0x18 [xhci_hcd])
[  155.240415]  r10:ee598200 r9:00000001 r8:00000002 r7:00000001 r6:00000003 r5:00000002
[  155.248363]  r4:ee49f000
[  155.250978] [<bf27ebfc>] (xhci_address_device [xhci_hcd]) from [<bf20cb94>] (hub_port_init+0x1b8/0xa9c [usbcore])
[  155.261403] [<bf20c9dc>] (hub_port_init [usbcore]) from [<bf2101e0>] (hub_event+0x738/0x1020 [usbcore])
[  155.270874]  r10:ee598200 r9:ee7c0000 r8:ee7c0038 r7:ee518800 r6:ee49f000 r5:00000001
[  155.278822]  r4:00000000
[  155.281426] [<bf20faa8>] (hub_event [usbcore]) from [<c005754c>] (process_one_work+0x128/0x340)
[  155.290196]  r10:00000000 r9:00000003 r8:00000000 r7:fedfa000 r6:eeec5400 r5:ee598314
[  155.298151]  r4:ee434380
[  155.300718] [<c0057424>] (process_one_work) from [<c00578f8>] (worker_thread+0x158/0x49c)
[  155.308963]  r10:ee434380 r9:00000003 r8:eeec5400 r7:00000008 r6:ee434398 r5:eeec5400
[  155.316913]  r4:eeec5414
[  155.319482] [<c00577a0>] (worker_thread) from [<c005cc40>] (kthread+0xdc/0xf8)
[  155.326765]  r10:00000000 r9:00000000 r8:00000000 r7:c00577a0 r6:ee434380 r5:ee4441c0
[  155.334713]  r4:00000000 r3:00000000
[  155.338341] [<c005cb64>] (kthread) from [<c000fc08>] (ret_from_fork+0x14/0x2c)
[  155.345626]  r7:00000000 r6:00000000 r5:c005cb64 r4:ee4441c0
[  155.356108] ---[ end trace a58d34c223b190e6 ]---
[  155.360783] xhci-hcd xhci-hcd.0.auto: Virt dev invalid for slot_id 0x1!
[  155.574404] xhci-hcd xhci-hcd.0.auto: xhci_setup_device
[  155.579667] ------------[ cut here ]------------

Cc: <stable@vger.kernel.org>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci_stop will be called twice, once for the shared hcd
and again for the primary hcd.

We stop the XHCI controller in any case so clean up
everything on the first call else we can timeout
waiting for pending requests to complete.

Cc: <stable@vger.kernel.org>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For whatever reason if XHCI died in the previous instant
then it will never recover on the next xhci_start unless we
clear the DYING flag.

Cc: <stable@vger.kernel.org>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Else it races with xhci_setup_device

Cc: <stable@vger.kernel.org>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit checks for the URB_ZERO_PACKET flag and creates an extra
zero-length td if the urb transfer length is a multiple of the endpoint's
max packet length.
Signed-off-by: NReyad Attiyat <reyad.attiyat@gmail.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace redundant variable use in return statement.
Signed-off-by: NSaurabh Karajgaonkar <skarajga@visteon.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "though" to "through" in documentation of xhci_alloc_streams().
Signed-off-by: NLuis de Bethencourt <luis@debethencourt.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When resetting a device the number of active TTs may need to be
corrected by xhci_update_tt_active_eps, but the number of old active
endpoints supplied to it was always zero, so the number of TTs and the
bandwidth reserved for them was not updated, and could rise
unnecessarily.

This affected systems using Intel's Patherpoint chipset, which rely on
software bandwidth checking.  For example, a Lenovo X230 would lose the
ability to use ports on the docking station after enough suspend/resume
cycles because the bandwidth calculated would rise with every cycle when
a suitable device is attached.

The correct number of active endpoints is calculated in the same way as
in xhci_reserve_bandwidth.

Cc: <stable@vger.kernel.org>
Signed-off-by: NBrian Campbell <bacam@z273.org.uk>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The comment stating that xhci_setup_device() is protected by the address
mutex is not true since
commit 6fecd4f2 ("USB: separate usb_address0 mutexes for each bus")
as xhci handles two buses.
Signed-off-by: NChris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the OTG case, the controller might not yet have been
added or is removed before the system suspends.

Assign xhci->main_hcd during probe to prevent NULL
pointer de-reference in xhci_suspend/resume().

Use the hcd->state flag to check if HCD is halted
and if that is so do nothing for xhci_suspend/resume().

[Only for xhci-plat devices, pci devices need it in gen_setup -Mathias]
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't set xhci->shared_hcd to NULL in xhci_stop() as we have
still not de-allocated it. It was resulting in a NULL pointer
de-reference if usb_add/remove_hcd() is called repeatedly.

We want repeated add/remove to work for the OTG use case.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

HCD core allocates memory for HCD private data in
usb_create_[shared_]hcd() so make use of that
mechanism to allocate the struct xhci_hcd.

Introduce struct xhci_driver_overrides to provide
the size of HCD private data and hc_driver operation
overrides. As of now we only need to override the
reset and start methods.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>