TI shared transport driver previously intended to expose rfkill
entries for each of the protocol gpio that the chip would have.
However now in case such gpios exist, which requires to be enabled
for a specific protocol, the responsibility lay on protocol driver.
This patch removes the request/free of multiple gpios, rfkill struct
references and also removes the chip_toggle function.
Signed-off-by: NPavan Savoy <pavan_savoy@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Where file-transfer stops/pauses in between, is
result of a HCI-LL anamoly in ST LL driver.
ST LL did not copy the contents of WaitQ into the TxQ, when a WAKEUP_IND
collision happened.
Make also sure, that the copying mechanism is safe, by wrapping it around
spin locks inside st_int_recv().
This was easily reproduced when the sleep timeout was reduced to 100ms
for HCI-LL.
Signed-off-by: NPavan Savoy <pavan_savoy@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

To fasten the process of firmware download, the chip allows
disabling of the command complete event generation from host.
In these cases, only few very essential commands would have
the command complete events and hence the wait associated with
them.

So now the driver would wait for a command complete event, only
when it comes across a wait event during firmware parsing.
This would also mean we need to skip not just the change baud
rate command but also the wait for it.
Signed-off-by: NPavan Savoy <pavan_savoy@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

pr_debug-ing few pr_infos from the data paths such as tty receive and
write so as to reduce debugs when we have higher logging levels enabled
undef VERBOSE in receive to avoid huge logs when log level 8 is set.
Signed-off-by: NPavan Savoy <pavan_savoy@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

set-right the error codes that the shared transport driver
returns.
Instead of magic numbers like -1, return relevant codes such as
ETIMEDOUT or EIO, EAGAIN when wait times out or uart write bytes don't
match expected value or when registration fails and needs to be
attempted again.
Signed-off-by: NPavan Savoy <pavan_savoy@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The communication between ST KIM and UIM was interfaced
over the /dev/rfkill device node.
Move the interface to a simpler less abusive sysfs entry
mechanism and document it in Documentation/ABI/testing/
under sysfs-platform-kim.

Shared transport driver would now read the UART details
originally received by bootloader or firmware as platform
data.
The data read will be shared over sysfs entries for the user-space
UIM or other n/w manager/plugins to be read, and assist the driver
by opening up the UART, setting the baud-rate and installing the
line discipline.
Signed-off-by: NPavan Savoy <pavan_savoy@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The architecture of shared transport had begun with individual
protocols like bluetooth, fm and gps telling the shared transport
what sort of protocol they are and then expecting the ST driver
to parse the incoming data from chip and forward data only
relevant to the protocol drivers.

This change would mean each protocol drivers would also send
information to ST driver as to how to intrepret their protocol
data coming out of the chip.
Signed-off-by: NPavan Savoy <pavan_savoy@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add ML7213 device information.
ML7213 is companion chip of Intel Atom E6xx series for IVI(In-Vehicle Infotainment).
ML7213 is completely compatible for Intel EG20T PCH.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since we don't have a PWM API every PWM driver ends up exporting its
own version and we need to limit the platforms we try to build them on
in order to avoid multiple definitions. As the AB8500 is normally a
companion chip for the U8500 CPU depend on that architecture.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

drivers/misc/cs5535-mfgpt.c: In function 'cs5535_mfgpt_probe':
drivers/misc/cs5535-mfgpt.c:320: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/misc/cs5535-mfgpt.c:320: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'

Use vsprintf extension %pR to format resource.
Original-patch-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds MODULE_ALIAS entries to the various cs5535 subdevice modules; this
allows the modules to automatically be loaded when cs5535-mfd loads.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The cs5535-mfd driver now takes care of the PCI BAR handling; this
simplifies the mfgpt driver a bunch.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When hypervisor decides to decrease target balloon size while the balloon
driver tries to lock pages hypervisor may respond with
VMW_BALLOON_PPN_NOTNEEDED.  Use this data and immediately stop reserving
pages and wait for the next update cycle to fetch new target instead of
continuing trying to lock pages until size of refused list grows above
VMW_BALLOON_MAX_REFUSED (16) pages.

As a result the driver stops bothering the hypervisor with its attempts to
lock more pages that are not needed anymore.  Most likely next order from
hypervisor will be to reduce ballon size anyway.

It is a small optimization.
Signed-off-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There is no reason to dynamically allocate work_struct for
ioc4_load_modules().  It makes the code more complex and makes it
impossible to flush the work directly.  Use static work
ioc4_load_modules_work instead and flush it directly on exit.

This removes the use of flush_scheduled_work() which is being
deprecated.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Brent Casavant <bcasavan@sgi.com>

Side-effects happen when passing 0 to either io_limit or page_size. Give
an error in case of this misconfiguration.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Information about the pagesize and read-only-status may also come from
the devicetree. Parse this data, too, and act accordingly. While we are
here, change the initialization printout a bit. write_max is useful to
know to detect performance bottlenecks, the rest is superfluous.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

struct als_data *data is not used in this driver at all.

Also add a missing ">" character for MODULE_AUTHOR.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

UV hardware defines 256 memory protection regions versus the baseline 64
with increasing size for the SN2 ia64.  This was overlooked when XPC was
modified to accomodate both UV and SN2.

Without this patch, a user could reconfigure their existing system and
suddenly disable cross-partition communications with no indication of what
has gone wrong.  It also prevents larger configurations from using
cross-partition communication.
Signed-off-by: NRobin Holt <holt@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

There was a signedness bug so "ret" was never less than zero and that
breaks the error handling.  Also in the original code it would overwrite
ret and the result is still negative but it's bogus number instead of the
correct error code.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

i2c_smbus_read_byte_data() may return negative error code.  This is not
seen to als_sensing_range_store() as the result is stored in unsigned int.

Made it signed.
Signed-off-by: NVasiliy Kulikov <segooon@gmail.com>
Cc: Hong Liu <hong.liu@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Anantha Narayanan <anantha.narayanan@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

"ret_val" is supposed to be signed here or the error handling breaks.
Also we should check the return value from i2c_smbus_read_byte_data().
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The "kgdb_connected" variable of debug_core just indicates whether or
not kgdbts is connected to the debug_core.  It does not completely
prevent a script from trying invoke kgdbts again and possibly crashing
the system (see Call Trace below).

The configured variable in kgtbts can be used instead of
kgdb_connected instead of kgdb_connected. The cleanup_kgdbts() can
also be removed because there is no possible way to build kgdbts as a
kernel module that you could unload with rmmod.

Call Trace:
-----------------------------------------------------------------
root:/$ echo kgdbts=V1S1000 > /sys/module/kgdbts/parameters/kgdbts
kgdb: Unregistered I/O driver kgdbts, debugger disabled.
------------[ cut here ]------------
WARNING: at kernel/debug/debug_core.c:1002
kgdb_unregister_io_module+0xec/0x100()
Hardware name: Moon Creek platform
Modules linked in:
Pid: 664, comm: sh Not tainted 2.6.34.1-WR4.0.0.0_standard #58
Call Trace:
 [<c103b1ed>] warn_slowpath_common+0x6d/0xa0
 [<c1079fdc>] ? kgdb_unregister_io_module+0xec/0x100
 [<c1079fdc>] ? kgdb_unregister_io_module+0xec/0x100
 [<c10544e0>] ? param_attr_store+0x0/0x20
 [<c103b235>] warn_slowpath_null+0x15/0x20
 [<c1079fdc>] kgdb_unregister_io_module+0xec/0x100
 [<c124e4ea>] cleanup_kgdbts+0x1a/0x20
 [<c124eced>] param_set_kgdbts_var+0x6d/0xb0
 [<c124ec80>] ? param_set_kgdbts_var+0x0/0xb0
 [<c10544f7>] param_attr_store+0x17/0x20
 [<c105457c>] module_attr_store+0x2c/0x40
 [<c111fe84>] sysfs_write_file+0x94/0xf0
 [<c10d42f6>] vfs_write+0x96/0x130
 [<c111fdf0>] ? sysfs_write_file+0x0/0xf0
 [<c10d44d6>] sys_write+0x46/0xd0
 [<c13bf329>] system_call_done+0x0/0x4
---[ end trace 4eb028c6ee43154c ]---
kgdb: Unregistered I/O driver kgdbts, debugger disabled.
-----------------------------------------------------------------

[jason.wessel@windriver.com: remove cleanup_kgdbts() ]
Signed-off-by: NDongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

This patch adds a Pulse Width Modulation driver for Analog Baseband
Chip AB8500.
Signed-off-by: NArun Murthy <arun.murthy@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Do not enable this Kconfig menu by default since it contains devices not
present on the majority of systems.

This is becoming a pain and a waste of time especially when doing a bunch
of kernel builds on different systems daily and have to answer "make
oldconfig" prompts for strange devices.
Signed-off-by: NBorislav Petkov <bp@alien8.de>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Andres Salomon <dilinger@collabora.co.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update the driver for the needed runtime power features.  Remove the old
user controlled power functions.

[akpm@linux-foundation.org: put PM code under CONFIG_PM]
Signed-off-by: NHong Liu <hong.liu@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds support for the ADPS9802ALS sensor.

Cleanup by Alan Cox
	- move mutexes to cover more things
	- report I/O errors back to user space
	- report range and values in LUX
Signed-off-by: NAnantha Narayanan <anantha.narayanan@intel.com>
[The 4K and 64K in the hw spec actually means 4095 (12bit) and 65535 (16bit).]
Signed-off-by: NHong Liu <hong.liu@intel.com>
[Updated to match the ALS light API interface convention from Samu]
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The LS driver will read the latest Lux measurement based upon the light
brightness and will report the LUX output through sysfs interface.

This hardware isn't quite the same as the ISL29003 so has a different
driver.

[akpm@linux-foundation.org: put PM code under #ifdef CONFIG_PM]
Signed-off-by: NKalhan Trisal <kalhan.trisal@intel.com>
[Runtime power management support added]
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
[Fixes to runtime PM]
Signed-off-by: NLiu Hong <hong.liu@intel.com>
[Cleanups and added checks for I2C errors, reworked the API to match the
 saner one agreed for other sensors]
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Prefix cname and ctype constants with CN/CT_.  This is especially for the
conflict on BUG which causes a build break if arch defines it as a inline
function, i.e.  MIPS.
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Cc: Ankita Garg <ankita@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a driver for Avago APDS990X combined ALS and proximity sensor.

Interface is sysfs based.  The driver uses interrupts to provide new data.
The driver supports pm_runtime and regulator frameworks.

See Documentation/misc-devices/apds990x.txt for details
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a driver for ROHM BH1770GLC and OSRAM SFH7770 combined ALS and
proximity sensor.

Interface is sysfs based.  The driver uses interrupts to provide new data.
 The driver supports pm_runtime and regulator frameworks.

See Documentation/misc-devices/bh1770glc.txt for details
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ad5251/ad5252 devices have rdac1 and rdac3, but no rdac0.  So make
sure we use the right channels so userspace gets correct data and not just
garbage.
Signed-off-by: Nsteven miao <realmz6@gmail.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Chris Verges <chrisv@cyberswitching.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for AD5270, AD5271, AD5272, AD5274 digital potentiometers.
Add 20-TP feature for AD5291 and AD5292 parts, and update feature list.
AD5291 rdac read back must be shifted by two.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Chris Verges <chrisv@cyberswitching.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There is no runtime effect by this change.  It frees up namespace for
defines erroneously used.  This is required to actually support devices
requiring the namespace, added with "drivers/misc/ad525x_dpot.c: new
features".

All defines touched have the same value defined, after the change.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Chris Verges <chrisv@cyberswitching.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

phantom_probe() can fail in many places.  Add missing warning messages in
pci_enable_device() and pci_request_regions().
Signed-off-by: NRahul Ruikar <rahul.ruikar@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a bug fix.  Some SPI connected devices using 16/24 bit accesses,
previously failed, now work.

This typo slipped in after testing, during some restructuring.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Chris Verges <chrisv@cyberswitching.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sgi-xp: incoming XPC channel messages can come in after the channel's partition structures have been torn down

Under some workloads, some channel messages have been observed being
delayed on the sending side past the point where the receiving side has
been able to tear down its partition structures.

This condition is already detected in xpc_handle_activate_IRQ_uv(), but
that information is not given to xpc_handle_activate_mq_msg_uv().  As a
result, xpc_handle_activate_mq_msg_uv() assumes the structures still exist
and references them, causing a NULL-pointer deref.
Signed-off-by: NRobin Holt <holt@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>