On some platforms(e.g. rk3399 board), we can call hcd_add/remove
consecutively without calling usb_put_hcd/usb_create_hcd in between,
so hcd->flags can be stale.

If the HC dies due to whatever reason then without this patch we get
the below error on next hcd_add.

[173.296154] xhci-hcd xhci-hcd.2.auto: HC died; cleaning up
[173.296209] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[173.296762] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 6
[173.296931] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[173.297179] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[173.297203] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[173.297222] usb usb6: Product: xHCI Host Controller
[173.297240] usb usb6: Manufacturer: Linux 4.4.21 xhci-hcd
[173.297257] usb usb6: SerialNumber: xhci-hcd.2.auto
[173.298680] hub 6-0:1.0: USB hub found
[173.298749] hub 6-0:1.0: 1 port detected
[173.299382] rockchip-dwc3 usb@fe800000: USB HOST connected
[173.395418] hub 5-0:1.0: activate --> -19
[173.603447] irq 228: nobody cared (try booting with the "irqpoll" option)
[173.603493] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.21 #9
[173.603513] Hardware name: Google Kevin (DT)
[173.603531] Call trace:
[173.603568] [<ffffffc0002087dc>] dump_backtrace+0x0/0x160
[173.603596] [<ffffffc00020895c>] show_stack+0x20/0x28
[173.603623] [<ffffffc0004b28a8>] dump_stack+0x90/0xb0
[173.603650] [<ffffffc00027347c>] __report_bad_irq+0x48/0xe8
[173.603674] [<ffffffc0002737cc>] note_interrupt+0x1e8/0x28c
[173.603698] [<ffffffc000270a38>] handle_irq_event_percpu+0x1d4/0x25c
[173.603722] [<ffffffc000270b0c>] handle_irq_event+0x4c/0x7c
[173.603748] [<ffffffc00027456c>] handle_fasteoi_irq+0xb4/0x124
[173.603777] [<ffffffc00026fe3c>] generic_handle_irq+0x30/0x44
[173.603804] [<ffffffc0002701a8>] __handle_domain_irq+0x90/0xbc
[173.603827] [<ffffffc0002006f4>] gic_handle_irq+0xcc/0x188
...
[173.604500] [<ffffffc000203700>] el1_irq+0x80/0xf8
[173.604530] [<ffffffc000261388>] cpu_startup_entry+0x38/0x3cc
[173.604558] [<ffffffc00090f7d8>] rest_init+0x8c/0x94
[173.604585] [<ffffffc000e009ac>] start_kernel+0x3d0/0x3fc
[173.604607] [<0000000000b16000>] 0xb16000
[173.604622] handlers:
[173.604648] [<ffffffc000642084>] usb_hcd_irq
[173.604673] Disabling IRQ #228
Signed-off-by: NWilliam wu <wulf@rock-chips.com>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The variable Newblk was only being assigned some value but was never
used after that.
Signed-off-by: NSudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The variable live was assigned the host controller running status but
it was never used or checked after that.
Signed-off-by: NSudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The commonly use of bottom halves are tasklet and workqueue. The big
difference between tasklet and workqueue is that the tasklet runs in
an interrupt context and the workqueue runs in a process context,
which means it can sleep if need be.

The comment for usb_control/interrupt/bulk_msg() functions note that do
not use this function within an interrupt context, like a 'bottom half'
handler. With this comment, it makes confuse about usage of these
functions.

To more clarify, remove 'bottom half' comment.
Signed-off-by: NJaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If a URB is killed while the host is removed we can end up in a situation
where the hub thread takes the roothub device lock, and waits for
the URB to be given back by xhci-hcd, blocking the host remove code.

xhci-hcd tries to stop the endpoint and give back the urb, but can't
as the host is removed from PCI bus at the same time, preventing the normal
way of giving back urb.

Instead we need to rely on the stop command timeout function to give back
the urb. This xhci_stop_endpoint_command_watchdog() timeout function
used a XHCI_STATE_DYING flag to indicate if the timeout function is already
running, but later this flag has been taking into use in other places to
mark that xhci is dying.

Remove checks for XHCI_STATE_DYING in xhci_urb_dequeue. We are still
checking that reading from pci state does not return 0xffffffff or that
host is not halted before trying to stop the endpoint.

This whole area of stopping endpoints, giving back URBs, and the wathdog
timeout need rework, this fix focuses on solving a specific deadlock
issue that we can then send to stable before any major rework.

Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A short control transfer would currently fail to be detected, something
which could lead to stale buffer data being used as valid input.

Check for short transfers, and make sure to log any transfer errors.

Note that this also avoids leaking heap data to user space (TIOCMGET)
and the remote device (break control).

Fixes: 6ce76104 ("USB: Driver for CH341 USB-serial adaptor")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

MUSB driver now has runtime PM support, but the debugfs driver misses
the PM _get/_put() calls, which could cause MUSB register access
failure.

Cc: stable@vger.kernel.org # 4.9+
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver put a constant buffer of all zeros on the stack and
pointed a scatterlist entry at it.  This doesn't work with virtual
stacks.  Use ZERO_PAGE instead.

Cc: stable@vger.kernel.org # 4.9 only
Reported-by: NEric Biggers <ebiggers3@gmail.com>
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Promote a variable keeping track of USB transfer memory usage to a
wider data type and allow for higher bandwidth transfers from a large
number of USB devices connected to a single host.
Signed-off-by: NMateusz Berezecki <mateuszb@fastmail.fm>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount.  Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.

Fixes: 6d40500a ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs")
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount.  Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.

Fixes: 6d40500a ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs")
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The MIPS based MT7621 shares the same XHCI core as the newer generation of
ARM based SoCs. The driver works out of the box and we only need to make it
buildable in Kconfig.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

trivial fix to typo in dev_dbg message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Defer probe if PHY is missing. E.g. on Nokia 770 several modules needs
to be loaded to get the PHY going and ohci-omap should wait for those.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The current implementation failed to detect short transfers when
attempting to read the line state, and also, to make things worse,
logged the content of the uninitialised heap transfer buffer.

Fixes: abf492e7 ("USB: kl5kusb105: fix DMA buffers on stack")
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Revert to using direct register writes to set the divisor and
line-control registers.

A recent change switched to using the init vendor command to update
these registers, something which also enabled support for CH341A
devices. It turns out that simply setting bit 7 in the divisor register
is sufficient to support CH341A and specifically prevent data from being
buffered until a full endpoint-size packet (32 bytes) has been received.

Using the init command also had the side-effect of temporarily
deasserting the DTR/RTS signals on every termios change (including
initialisation on open) something which for example could cause problems
in setups where DTR is used to trigger a reset.

Fixes: 4e46c410 ("USB: serial: ch341: reinitialize chip on
reconfiguration")
Signed-off-by: NJohan Hovold <johan@kernel.org>

A recent change added support for modifying the default line-control
settings, but did not make sure that the modified settings were used as
part of reconfiguration after a device has been reset during resume.

This caused a port that was open before suspend to be unusable until
being closed and reopened.

Fixes: ba781bdf ("USB: serial: ch341: add support for parity, frame
length, stop bits")
Signed-off-by: NJohan Hovold <johan@kernel.org>

Fix reset-resume handling which failed to resubmit the read and
interrupt URBs, thereby leaving a port that was open before suspend in a
broken state until closed and reopened.

Fixes: 1ded7ea4 ("USB: ch341 serial: fix port number changed after
resume")
Fixes: 2bfd1c96 ("USB: serial: ch341: remove reset_resume callback")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Make sure to stop the interrupt URB before returning on errors during
open.

Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The modem-control signals are managed by the tty-layer during open and
should not be asserted prematurely when set_termios is called from
driver open.

Also make sure that the signals are asserted only when changing speed
from B0.

Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The private baud_rate variable is used to configure the port at open and
reset-resume and must never be set to (and left at) zero or reset-resume
and all further open attempts will fail.

Fixes: aa91def4 ("USB: ch341: set tty baud speed according to tty
struct")
Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

DTR and RTS will be asserted by the tty-layer when the port is opened
and deasserted on close (if HUPCL is set). Make sure the initial state
is not-asserted before the port is first opened as well.

Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses.  This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:

WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...

CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
 ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c
 ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510
 ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000
Call Trace:
 [<     inline     >] __dump_stack lib/dump_stack.c:15
 [<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51
 [<ffffffff8168c88e>] panic+0x1cb/0x3a9 kernel/panic.c:179
 [<ffffffff812b80b4>] __warn+0x1c4/0x1e0 kernel/panic.c:542
 [<ffffffff812b8195>] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565
 [<ffffffff819e70ca>] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30
 [<ffffffff819e7308>] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59
 [<     inline     >] create_dir lib/kobject.c:71
 [<ffffffff81fa1b07>] kobject_add_internal+0x227/0xa60 lib/kobject.c:229
 [<     inline     >] kobject_add_varg lib/kobject.c:366
 [<ffffffff81fa2479>] kobject_add+0x139/0x220 lib/kobject.c:411
 [<ffffffff82737a63>] device_add+0x353/0x1660 drivers/base/core.c:1088
 [<ffffffff82738d8d>] device_register+0x1d/0x20 drivers/base/core.c:1206
 [<ffffffff82cb77d3>] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195
 [<ffffffff82c9f27b>] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030
 [<ffffffff82ca39d3>] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937
 [<ffffffff82cc9e2e>] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172
 [<ffffffff82caa7fa>] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263

This patch prevents the problem by checking for duplicate endpoint
addresses during enumeration and skipping any duplicates.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NAndrey Konovalov <andreyknvl@google.com>
Tested-by: NAndrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The gpiod_get* function family does not want the -gpio suffix.
Use devm_gpiod_get_index_optional instead of devm_gpiod_get_optional.
The descriptor based APIs handle active high/low automatically.
The vbus-gpios are output, request enable while getting the gpio.
Don't try to get any vbus-gpios for ports outside num-ports.

WTF? Big sigh.

Fixes: 054d4b7b ("usb: ohci-at91: Use descriptor-based gpio APIs")
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This device gives the following error on detection.
xhci_hcd 0000:00:11.0: ERROR Transfer event for disabled endpoint or
incorrect stream ring

The same error is not seen when it is added to unusual_device
list with US_FL_NO_REPORT_OPCODES passed.
Signed-off-by: NGeorge Cherian <george.cherian@cavium.com>
Signed-off-by: NOliver Neukum <oneukun@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If CONFIG_PM=n:

    drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
    drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here

To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.

Fixes: 37be6676 ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices")
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The function bfin_fifo_offset is defined but not used:

drivers/usb/musb/blackfin.c:36:12: warning: ‘bfin_fifo_offset’ defined
but not used [-Wunused-function]
 static u32 bfin_fifo_offset(u8 epnum)
             ^~~~~~~~~~~~~~~~

Adding bfin_fifo_offset to bfin_ops fixes this warning and allows musb
core to call this function instead of default_fifo_offset.

Fixes: cc92f681 ("usb: musb: Populate new IO functions for blackfin")
Signed-off-by: NJérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The function musb_run_resume_work is called only when CONFIG_PM is
enabled. So this function should not be defined when CONFIG_PM is
disabled. Otherwise the compiler issues a warning:

drivers/usb/musb/musb_core.c:2057:12: error: ‘musb_run_resume_work’ defined but
not used [-Werror=unused-function]
 static int musb_run_resume_work(struct musb *musb)
            ^~~~~~~~~~~~~~~~~~~~
Signed-off-by: NJérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When unloading omap2430, we can get the following splat:

WARNING: CPU: 1 PID: 295 at kernel/irq/manage.c:1478 __free_irq+0xa8/0x2c8
Trying to free already-free IRQ 4
...
[<c01a8b78>] (free_irq) from [<bf0aea84>]
(musbhs_dma_controller_destroy+0x28/0xb0 [musb_hdrc])
[<bf0aea84>] (musbhs_dma_controller_destroy [musb_hdrc]) from
[<bf09f88c>] (musb_remove+0xf0/0x12c [musb_hdrc])
[<bf09f88c>] (musb_remove [musb_hdrc]) from [<c056a384>]
(platform_drv_remove+0x24/0x3c)
...

This is because the irq number in use is 260 nowadays, and the dma
controller is using u8 instead of int.

Fixes: 6995eb68 ("USB: musb: enable low level DMA operation for Blackfin")
Signed-off-by: NTony Lindgren <tony@atomide.com>
[b-liu@ti.com: added Fixes tag]
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.

    musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0

    musb_host_rx 1936: RX3 dma busy, csr 2020

As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt, so implement clear_ep_rxintr()
callback.

This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.

cc: stable@vger.kernel.org # 4.1+
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.

	musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0

	musb_host_rx 1936: RX3 dma busy, csr 2020

As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt.

Clearing ep interrupt is platform dependent, so this patch adds a
platform callback to allow glue driver to clear the ep interrupt.

This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.

cc: stable@vger.kernel.org # 4.1+
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix NULL-pointer dereference in open() should a malicious device lack
the expected endpoints:

Unable to handle kernel NULL pointer dereference at virtual address 00000030
..
[<bf06a6b0>] (ti_open [ti_usb_3410_5052]) from [<bf02e118>] (serial_port_activate+0x68/0x98 [usbserial])

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:

Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at spcp8x5_open+0x30/0xd0 [spcp8x5]

Fixes: 619a6f1d ("USB: add usb-serial spcp8x5 driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The write URB was being killed using the synchronous interface while
holding a spin lock in close().

Simply drop the lock and busy-flag update, something which would have
been taken care of by the completion handler if the URB was in flight.

Fixes: f7a33e60 ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Fix NULL-pointer dereference in open() should a type-0 or type-1 device
lack the expected endpoints:

Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at pl2303_open+0x38/0xec [pl2303]

Note that a missing interrupt-in endpoint would have caused open() to
fail.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:

Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at oti6858_open+0x30/0x1d0 [oti6858]

Note that a missing interrupt-in endpoint would have caused open() to
fail.

Fixes: 49cdee0e ("USB: oti6858 usb-serial driver (in Nokia CA-42
cable)")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Fix NULL-pointer dereferences at open() and disconnect() should the
device lack the expected bulk-out endpoints:

Unable to handle kernel NULL pointer dereference at virtual address 000000b4
...
[c0170ff0>] (__lock_acquire) from [<c0172f00>] (lock_acquire+0x108/0x264)
[<c0172f00>] (lock_acquire) from [<c06a5090>] (_raw_spin_lock_irqsave+0x58/0x6c)
[<c06a5090>] (_raw_spin_lock_irqsave) from [<c0470684>] (tty_port_tty_set+0x28/0xa4)
[<c0470684>] (tty_port_tty_set) from [<bf08d384>] (omninet_open+0x30/0x40 [omninet])
[<bf08d384>] (omninet_open [omninet]) from [<bf07c118>] (serial_port_activate+0x68/0x98 [usbserial])

Unable to handle kernel NULL pointer dereference at virtual address 00000234
...
[<bf01f418>] (omninet_disconnect [omninet]) from [<bf0016c0>] (usb_serial_disconnect+0xe4/0x100 [usbserial])

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The interrupt URB is killed at final port close since commit
0de9a702 ("USB: overhaul of mos7840 driver").

Fixes: 0de9a702 ("USB: overhaul of mos7840 driver")
Signed-off-by: NJohan Hovold <johan@kernel.org>

Remove code to manage a write URB that was never allocated.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:

Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at mos7840_open+0x88/0x8dc [mos7840]

Note that we continue to treat the interrupt-in endpoint as optional for
now.

Fixes: 3f542974 ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>