Cleaning up arch/powerpc/Kconfig platform support.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds a cpufreq backend driver to enable frequency scaling on cell.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch adds a module that registers sysfs attributes to CPU and SPU
containing the temperature of the CBE.

They can be found under
/sys/devices/system/spu/cpuX/thermal/temperature[0|1]
/sys/devices/system/spu/spuX/thermal/temperature

The temperature is read from the on-chip temperature sensors.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch adds a new "psmap" file to spufs that allows mmap of all of
the problem state mapping of SPEs. It is compatible with 64k pages. In
addition, it removes mmap ability of individual files when using 64k
pages, with the exception of signal1 and signal2 which will both map the
entire 64k page holding both registers. It also removes
CONFIG_SPUFS_MMAP as there is no point in not building mmap support in
spufs.

It goes along a separate patch to libspe implementing usage of that new
file to access problem state registers.

Another patch will follow up to fix races opened up by accessing
the 'runcntl' register directly, which is made possible with this
patch.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

spufs_base.c calls __add_pages, which depends on CONFIG_MEMORY_HOTPLUG.

Moved the selection of CONFIG_MEMORY_HOTPLUG from CONFIG_SPUFS_MMAP
to CONFIG_SPU_FS.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Creates new config variables PPC_CELL_NATIVE and PPC_IBM_CELL_BLADE.
The existing CONFIG_PPC_CELL is now used to denote the generic
Cell processor support.

PPC_CELL = make descends into platforms/cell
PPC_CELL_NATIVE = add bare metal support
PPC_IBM_CELL_BLADE = add blade device drivers, etc.

Also renames spu_priv1.c to spu_priv1_mmio.c.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is a first version of support for the Cell BE "Reliability,
Availability and Serviceability" features.

It doesn't yet handle some of the RAS interrupts (the ones described in
iic_is/iic_irr), I'm still working on a proper way to expose these. They
are essentially a cascaded controller by themselves (sic !) though I may
just handle them locally to the iic driver. I need also to sync with
David Erb on the way he hooked in the performance monitor interrupt.

So that's all for 2.6.17 and I'll do more work on that with my rework of
the powerpc interrupt layer that I'm hacking on at the moment.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Based on an older patch from  Mike Kravetz <kravetz@us.ibm.com>

We need to have a mem_map for high addresses in order to make fops->no_page
work on spufs mem and register files.  So far, we have used the
memory_present() function during early bootup, but that did not work when
CONFIG_NUMA was enabled.

We now use the __add_pages() function to add the mem_map when loading the
spufs module, which is a lot nicer.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch is layered on top of CONFIG_SPARSEMEM
and is patterned after direct mapping of LS.

This patch allows mmap() of the following regions:
"mfc", which represents the area from [0x3000 - 0x3fff];
"cntl", which represents the area from [0x4000 - 0x4fff];
"signal1" which begins at offset 0x14000; "signal2" which
begins at offset 0x1c000.

The signal1 & signal2 files may be mmap()'d by regular user
processes.  The cntl and mfc file, on the other hand, may
only be accessed if the owning process has CAP_SYS_RAWIO,
because they have the potential to confuse the kernel
with regard to parallel access to the same files with
regular file operations: the kernel always holds a spinlock
when accessing registers in these areas to serialize them,
which can not be guaranteed with user mmaps,
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is the current version of the spu file system, used
for driving SPEs on the Cell Broadband Engine.

This release is almost identical to the version for the
2.6.14 kernel posted earlier, which is available as part
of the Cell BE Linux distribution from
http://www.bsc.es/projects/deepcomputing/linuxoncell/.

The first patch provides all the interfaces for running
spu application, but does not have any support for
debugging SPU tasks or for scheduling. Both these
functionalities are added in the subsequent patches.

See Documentation/filesystems/spufs.txt on how to use
spufs.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>