Some files are getting bloated and it makes sense
to split some of the code into separate files. Do
so with the P2P NoA code and prepare it for reuse.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware doesn't report a complete and
ready-to-use vht cap. Instead the driver is
supposed to fill in the missing bits related to
number of chains.

This effectively increases Compressed Steering
Number and Number of Sounding Dimensions in
AssocReq frames for devices with more than one RF
chain and should improve TxBF performance.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The command was truncated so the parameter value
was seen in fw as 0. This caused U-APSD enabled
stations to be misconfigured and mistreated by AP.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Allow user to configure the duty cycle upto 100%. Since thermal
mitigation algorithm is running in user space, remove the driver
level limitation and let the user to control the temperature.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When WEP keys are uploaded it's possible that
there are stations associated already (e.g. when
merging) without any keys. Static WEP needs an
explicit per-peer key upload.

Make sure to re-upload wep keys if necessary.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When running 802.1x WEP keys must be installed
without pairwise-groupwise swap (which is
necessary for static WEP).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This has been missed while adding the QCA6174 support.
As in the last time, without advertising the firmware files
as needed (or optional) for ath10k, these won't be built into
ram disk for instance.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca6174 with wmi-tlv firmware uses offloaded
beaconing scheme (i.e. templates). This requires a
little different approach when implementing CSA.

Add missing code to update CS count and report CSA
completion to mac80211. Without it channel switch
was never finished.

To avoid races during interface teardown data_lock
has been used to protect is_up and is_started so
they can be compared against before scheduling
count down work.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The current SKID length configuration causes firmware
to reject peer creation for not able to allocate
AST entries for peers. This issue is observed when
least significant 3 bytes are used ramdomly to create
client MAC addresses.

AST table SKID length configuration is increased to
maximum value to fix this issue.
Signed-off-by: NSenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Certain radar types such as FCC radar type 5 are using chirp
in their pulses, hence looking up the chirp status will enhance
to avoid false radar detection.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware reports chirp status in phy error event if it's detected
and the chirp status is valuable to distinguish radar types.
So save it to use for DFS parttern detector.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some of radar types such as FCC radar type 5 require
to look up chirp in pulse to detect genuine radar and
it will prevent DFS channels from false radar detection.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Having lower number of copy engine entries for target to host
WMI ring is causing drops in receiving management frames. This
issue is observed during max clients (128 clients) stress testing.
While bursting deauthentication frames from simulated clients,
approx. 70% of frames are getting dropped due to lower ring entries.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Not all firmware revisions have a proper
multi-interface client powersaving implementation,
e.g. qca6174 WLAN.RM.2.0-00073.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca6184 WLAN.RM.2.0-00073 has a bug in sta
powersave state machine and requires peer param to
be poked to enable the powersave.

Calling this unconditionally should be safe for
other chips/firmwares.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

During wmm tests changing wmm parameters did not change anything.
This was because of mismatch in WMM params per vdev command.
WMM params per vdev uses different command structure than wmm params
per pdev command.

Patch concerns qca6174.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca6174 WLAN.RM.2.0-00073 firmware uses full rx
reordering offload and delivers Rx via a new HTT
event. The event however is incorrectly generated
in firmware and becomes overly long (with trailing
garbage). This was hitting defined CE buffer limit
that was programmed to the device and caused
device to crash upon busier Rx traffic.

Increasing the CE buffer limit for HTT Rx pipe to
2KBytes seems to be enough to workaround this
problem.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

cppcheck detected a buffer overflow:

[drivers/net/wireless/ath/wil6210/debugfs.c:634]: (error) Width 8
  given in format string (no. 1) is larger than destination buffer
  'cmd[8]', use %7s to prevent overflowing it.

For the current %8s sscanf we require cmd to be 9 chars long
so increase it by 1 byte to prevent the sscan overflow (rather
than reduce the %8s specifier to %7s as cppcheck recommends).
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

* ath9k_mci_update_rssi() is required only for
  cards that use MCI scheme. Make sure that it
  is not called for 3-wire cards.

* Call ath9k_ps_wakeup() early since register
  accesses are made in ath9k_mci_update_rssi().

* Fix usage of btcoex_lock to handle no_stomp_timer.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Make sure that the btcoex timers are started/stopped
properly for both 3-wire and MCI schemes.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When disabling BTCOEX, clearing the wlanactive gpio line
is required only for pre-AR9003 cards.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Commit "ath9k_hw: remove ATH_BTCOEX_CFG_MCI" removed
MCI as a separate coex scheme, but we need it to
avoid fiddling with GPIO registers during
ath9k_init_btcoex() that are meant only for 3-wire
cards.

Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The MCI configuration values are assigned
in ath9k_hw_btcoex_init_mci() which are used
by the MCI reset routine. When initializing
BTCOEX/MCI, ath_mci_setup() ends up using
uninitialized data. Fix this by setting up
the configuration parameters before issuing
a MCI reset.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ath_init_btcoex_timer() always returns 0, so
checking for error conditions is not required.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In order to add per-vif TX power capability cap per-packet TX power to vif
configured power if the latter is lower than per-rate TX power and mac80211
per-frame power. Use vif TX power if TPC has been disabled for current the
interface
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Configure the HW with highest TX power among all vif when HW TPC has been
enabled in order to add support to per-vif TX power capability. Use lowest
configured power among all interfaces when TPC is disabled
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Set The BT/WLAN priority weights correctly and make sure
that MCI_LNA_TAKE is sent only for cards that share
PA/LNA.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Handle MCI_STATE_INIT_GPM_OFFSET separately and do not
overload ar9003_mci_get_next_gpm_offset() with a special
case.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The LNA_TRANS message needs to be sent only for
chips which have shared PA/LNA.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use a subroutine to enable MCI debug statistics
if it is present in the global configuration.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch makes sure that the antenna configuration
is used properly when setting AR_MCI_TX_CTRL.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The value programmed in the BTCOEX control register
is different for each chip. This patch adds support
for 2-ANT, 1-ANT solutions based on AR9565.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Several new MCI parameters need to be handled for
new chips, add them.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If we fail to allocate the sched/gpm buffers when
initializing MCI, we bail out properly. Checking
them in ar9003_mci_reset() is unnecessary, so remove it.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For the STA interface, track 'privacy'.
Refactor safety checks to:
- always print connection params
- always check IE size validity
- require RSN IE for secure connection
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Make this field to track privacy attribute for all interface types
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On some platforms get_cycles() implemented to allways return 0.
On such platforms "Division by zero" bug was triggered.
Signed-off-by: NBoris Sorochkin <boriss@codeaurora.org>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Change threshold to be variable debugfs entry from hard-coded 0.
Default threshold value is 16 descriptors because HW is capable
of fetching up to 16 descriptors at once.
Signed-off-by: NVladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>