Here is a driver for the Alchemy au1550 PSC (Programmable Serial
Controller) in SPI master mode.

It supports dma transfers using the Alchemy descriptor based dma controller
for 4-8 bits per word SPI transfers.  For 9-24 bits per word transfers, pio
irq based mode is used to avoid setup of dma channels from scratch on each
number of bits per word change.

Tested with au1550; this may also work on other MIPS Alchemy cpus, like
au1200/au1210/au1250.  Used extensively with SD card connected via SPI;
this handles 8.1MHz SPI clock transfers using dma without any problem (the
highest SPI clock freq possible with au1550 running on 324MHz).

The driver supports sharing of SPI bus by multiple devices.  All features
of Alchemy SPI mode are supported (all SPI modes, msb/lsb first, bits per
word in 4-24 range).

As the SPI clock of the controller depends on main input clock that shall
be configured externally, platform data structure for au1550 SPI controller
driver contains mainclk_hz attribute to define the input clock rate.  From
this value, dividers of the controller for SPI clock are set up for
required frequency.
Signed-off-by: NJan Nikitenko <jan.nikitenko@gmail.com>

Whitespace and section fixups.  Remove partial workaround for platform
setup bug in dma_mask setup; it couldn't work with multiple controllers.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Various documentation updates for the SPI infrastructure, to clarify things
that may not have been clear, to cope with lack of editing, and fix
omissions.

Also, plug SPI into the kernel-api DocBook template, and fix all the
resulting glitches in document generation.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a filesystem API for <linux/spi/spi.h> stack.  The initial version of
this interface is purely synchronous.

dbrownell@users.sourceforge.net:

 Cleaned up, bugfixed; much simplified; added preliminary documentation.

 Works with mdev given CONFIG_SYSFS_DEPRECATED; and presumably udev.

 Updated SPI_IOC_MESSAGE ioctl to full spi_message semantics, supporting
 groups of one or more transfers (each of which may be full duplex if
 desired).

 This is marked as EXPERIMENTAL with an explicit disclaimer that the API
 (notably the ioctls) is subject to change.
Signed-off-by: NAndrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Simplify the spi_butterfly driver by removing incomplete/unused support for
the second SPI bus, implemented by the USI controller.  This should make
this a clearer example of how to write a parport bitbang driver.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove some obviously old interrupt disable/enable code that has been
commented out.
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The misc character device driver uses a semaphore as mutex.  Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The hdaps driver uses a semaphore as mutex.  Use the mutex API instead of the
(binary) semaphore.
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Cc: Robert Love <rlove@rlove.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The TPM driver uses two semaphores as mutexes.  Use the mutex API instead of
the (binary) semaphores.
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Cc: Kylene Hall <kjhall@us.ibm.com>
Cc: Marcel Selhorst <tpm@selhorst.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The RocketPort driver uses a semaphore as mutex.  Use the mutex API instead of
the (binary) semaphore.
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change synclink_gt driver to use dynamic tty device registration.
Signed-off-by: NPaul Fulghum <paulkf@microgate.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add sensable phantom driver
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I noticed that the moxa input checking security bug described by
CVE-2005-0504 appears to remain unfixed upstream.

The issue is described here:
  http://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2005-0504

Debian has been shipping the following patch from Andres Salomon.

(akpm: it's a privileged operation)
Signed-off-by: Ndann frazier <dannf@hp.com>
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cc: Matt Reimer <mreimer@vpop.net>

[akpm@linux-foundation.org: kconfig update]
Signed-off-by: NMatt Reimer <mreimer@vpop.net>
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMatt Reimer <mreimer@vpop.net>
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

flush_scheduled_work() can sleep, and we're calling it under spinlock.

AFAICS, moving flush_scheduled_work before spin_lock() should not cause any
problems.

Reason being - The only thing that can race against tpm_release is tpm_open
(tpm_release is called when last reference to the file is closed and only
thing that can happen after that is tpm_open??) and tpm_open acquires
driver_lock and more over it bails out with EBUSY if chip->num_opens is
greater than 0.

I also moved chip->num_pending-- to after deleting timer and setting data
pending as it looks more correct for the paranoid although it probably doesn't
matter as it is guarded by driver_lock.  None the less this change should not
cause problems.

While I was at it I noticed a missing NULL check in tpm_register_hardware
which is fixed with this patch as well.
Signed-off-by: NParag Warudkar <parag.warudkar@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

use __set_current_state(TASK_*) instead of current->state = TASK_*,
Signed-off-by: NMilind Arun Choudhary <milindchoudhary@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ingo Molnar's semaphore to mutex conversions left some noise on a few
trylock calls. Clean it up.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The UTF-8 part of the vt driver suffers from the following issues which are
addressed in my patch:

1) If there's no glyph found for a particular valid UTF-8 character, we try
   to display U+FFFD. However if this one is not found either, here's what
   the current kernel does:

   - First, if the Unicode value is less than the number of glyphs, use the
     glyph directly from that position of the glyph table. While it may be a
     good idea in the 8-bit world, it has absolutely no sense with Unicode
     in mind. For example, if a Latin-2 font is loaded and an application
     prints U+00FB ("u with circumflex", not present in Latin-2) then as a
     fallback solution the glyph from the 0xFB position of the Latin-2
     fontset (which is an "u with double accent" - a different character) is
     displayed.

   - Second, if this fallback fails too, a simple ASCII question mark is
     printed, which is visually undistinguishable from a real question mark.

   I changed the code to skip the first step (except if in non-UTF-8 mode),
   and changed the second step to print the question mark with inverse color
   attributes, so it is visually clear that it's not a real question mark,
   and resembles more to the common glyph of U+FFFD.

2) The UTF-8 decoder is buggy in many ways:

   - Lone continuation bytes (section 3.1 of Markus Kuhn's UTF-8 stress
     test) are not caught, they are displayed as some "random" (taken
     directly form the font table, see above) glyphs instead the replacement
     character.

   - Incomplete sequences (sections 3.2 and 3.3 of the stress test) emit no
     replacement character, but rather cause the subsequent valid character
     to be displayed more times(!).

   - The decoder is not safe: overlong sequences are not caught currently,
     they are displayed as if these were valid representations. This may
     even have security impacts.

   - The decoder does not handle D800..DFFF and FFFE..FFFF specially, it
     just emits these code points and lets it be looked up in the glyph
     table. Since these are invalid code points, I replace them by U+FFFD
     and hence give no chance for them to be looked up in the glyph table.
     (Assuming no font ships glyphs for these code points, this change is
     not visible to the users since the glyph shown will be the same.)

   With my fixes to the decoder it now behaves exactly as Markus Kuhn's
   stress test recommends.

3) It has no concept of double-width (CJK) characters. It's way beyond the
   scope of my patch to try to display them, but at least I think it's
   important for the cursor to jump two positions when printing such
   characters, since this is what applications (such as text editors)
   expect. Currently the cursor only jumps one position, and hence
   applications suffer from displaying and refreshing problems, and editing
   some English letters that are preceded by some CJK characters in the same
   line is a nightmare. With my patch an additional space is inserted after
   the CJK character has been printed (which usually means a replacement
   symbol of course). (If U+FFFD isn't availble and hence an inverse
   question mark is displayed in the first cell, I keep the inverted state
   for the space in the 2nd column so it's quite easy to see that they are
   tied together.)

4) There is a small built-in table of zero-width spaces that are not to be
   printed but silently skipped. U+200A is included there, but it's not a
   zero-width character, so I remove it from there.
Signed-off-by: NEgmont Koblinger <egmont@uhulinux.hu>
Cc: Jan Engelhardt <jengelh@linux01.gwdg.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The serial_txx9 driver have abused device numbers (major 4, minor 128) if
CONFIG_SERIAL_TXX9_STDSERIAL was not set.  This patch makes the driver use
proper device numbers assigned for it (major 204, minor 196-203).  I
suppose a typical user of this driver set CONFIG_SERIAL_TXX9_STDSERIAL to Y
(i.e.  use "ttyS0"), so this patch would not cause big compatibility issue.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patches modifies the pnpbios kernel thread to start with ktrhead_run
not kernel_thread and deamonize.  Doing this makes the code a little
simpler and easier to maintain.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SPIN_LOCK_UNLOCKED cleanup,use __SPIN_LOCK_UNLOCKED instead
Signed-off-by: NMilind Arun Choudhary <milindchoudhary@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SPIN_LOCK_UNLOCKED cleanup,use __SPIN_LOCK_UNLOCKED instead
Signed-off-by: NMilind Arun Choudhary <milindchoudhary@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make cciss unconditionally include scsi/scsi.h, because of the use of
SCSI_IOCTL_GET_IDLUN and SCSI_IOCTL_GET_BUS_NUMBER.
Signed-off-by: NStephen M. Cameron <steve.cameron@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Simple driver that blinks the keyboard LEDs when loaded.  Useful for
checking that the kernel is still alive or for crashdumping
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We've had various reports of some legacy "probe the hardware" style
platform drivers having nasty problems with hotplug support.

The core issue is that those legacy drivers don't fully conform to the
driver model.  They assume a role that should be the responsibility of
infrastructure code: creating device nodes.

The "modprobe" step in hotplugging relies on drivers to have split those
roles into different modules.  The lack of this split causes the problems.
When a driver creates nodes for devices that don't exist (sending a hotplug
event), then exits (aborting one modprobe) before the "modprobe $MODALIAS"
step completes (by failing, since it's in the middle of a modprobe), the
result can be an endless loop of modprobe invocations ...  badness.

This fix uses the newish per-device flag controlling issuance of "add"
events.  (A previous version of this patch used a per-device "driver can
hotplug" flag, which only scrubbed $MODALIAS from the environment rather
than suppressing the entire hotplug event.) It also shrinks that flag to
one bit, saving a word in "struct device".

So the net of this patch is removing some nasty failures with legacy
drivers, while retaining hotplug capability for the majority of platform
drivers.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <gregkh@suse.de>
Cc: Andres Salomon <dilinger@debian.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Set rq->errors more correctly in cciss driver.  Previously we had set it
synonymously with the meaning of the last parameter of end_that_last_request
and complete_buffers (the "uptodate" parameter) and had gotten away with it
for all this time because nobody ever looked at rq->errors.
SCSI_IOCTL_SEND_COMMAND looks at rq->errors, so now it matters that it be
right.
Signed-off-by: NStephen M. Cameron <steve.cameron@hp.com>
Signed-off-by: NMike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For all of you that think cciss should be a scsi driver here is the patch that
you have been waiting for all these years. This patch actually adds the SG_IO
ioctl to cciss. The primary purpose is for clustering and high-availibilty.
But now anyone can exploit this ioctl in any manner they wish.

Note, SCSI_IOCTL_SEND_COMMAND doesn't work with this patch due to rq->errors
being set incorrectly.  Subsequent patch fixes that.
Signed-off-by: NStephen M. Cameron <steve.cameron@hp.com>
Signed-off-by: NMike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reformat some error handling code to reduce line lengths a bit.
Signed-off-by: NStephen M. Cameron <steve.cameron@hp.com>
Signed-off-by: NMike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes two things in module_init.

- fix register_chrdev() error check

  Currently dtlk doesn't check register_chrdev() failure correctly.
  register_chrdev() returns a errno on failure.

- check probe failure

  dtlk ignores probe failure and allows the module loading without
  such device. I got "Trying to free nonexistent resource" message
  by release_region() when unloading module without device.

[akpm@linux-foundation.org: fix error code return]
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Chris Pallotta <chris@allmedia.com>
Cc: Jim Van Zandt <jrv@vanzandt.mv.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/parport/parport_serial.c:402: warning: ignoring return value of 'pci_enable_device', declared with attribute warn_unused_result
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

  linux/module.h
  -> linux/elf.h
     -> asm-i386/elf.h
        -> linux/utsname.h
           -> linux/sched.h

Noticeably cut the number of files which are rebuild upon touching sched.h
and cut down pulled junk from every module.h inclusion.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ROUND_UP macro cleanup use DIV_ROUND_UP
Signed-off-by: NMilind Arun Choudhary <milindchoudhary@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the last users of the deprecated SA_xxx interrupt flags.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Teach PNPACPI how to hook up its devices to their ACPI nodes, so that
pnpdev->dev.archdata points to the parallel acpi device node.  Previously
this only worked for PCI, leaving a notable hole.

Export "acpi_bus_type" so this can work.

Remove some extraneous whitespace.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove artificial maximum 256 loop device that can be created due to a
legacy device number limit.  Searching through lkml archive, there are
several instances where users complained about the artificial limit that
the loop driver impose.  There is no reason to have such limit.

This patch rid the limit entirely and make loop device and associated block
queue instantiation on demand.  With on-demand instantiation, it also gives
the benefit of not wasting memory if these devices are not in use (compare
to current implementation that always create 8 loop devices), a net
improvement in both areas.  This version is both tested with creation of
large number of loop devices and is compatible with existing losetup/mount
user land tools.

There are a number of people who worked on this and provided valuable
suggestions, in no particular order, by:

Jens Axboe
Jan Engelhardt
Christoph Hellwig
Thomas M
Signed-off-by: NKen Chen <kenchen@google.com>
Cc: Jan Engelhardt <jengelh@linux01.gwdg.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of having /dev/port support dependent in multiple places on a
string of preprocessor symbols, define a new configuration directive for
it.  This ensures that all four places remain consistent with each other.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The 82875 EDAC driver enables an otherwise-hidden PCI device, but doesn't
register it as a PCI device properly.  Therefore, the device list in
/proc/bus/pci/devices is different than the tree in /sys/bus/pci.  This
usually manifests as the X server failing to start, since it expects the
two lists to be consistent.
Signed-off-by: NAdam Jackson <ajackson@redhat.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Doug Thompson <norsk5@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.

Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>