Only two things needed adjustment:
- pipe select for PCH_CPT
- There's no dithering bit on ilk+ in the lvds ctl reg
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A few things needed to change:
- HAS_PCH_SPLIT since ilk+ is not yet converted to this.
- s/LVDS/intel_lvds->reg/ to prep for ilk conversion
- replace the clock.p2 == 7 check with a is_dual_link check
- s/adjusted_mode/intel_lvds->fixed_mode

v2: Rebase on top of Jani Nikula's panel rework. I'm wondering whether
we shouldn't add an attached_panel pointer to intel_encoder, to
replace the encoder private ->attached_connector pointers, since
that's essentially what we need.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just a prep patch to make this a property of intel_lvds. Makes more
sense, removes clutter from intel_display.c and eventually I want to
move all the encoder special cases wrt clock handling to encoders
anyway.

v2: Add an intel_ prefixe to is_dual_link_lvds since it's non-static
now.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... with is_dual_link_lvds introduced in

commit b0354385
Author: Takashi Iwai <tiwai@suse.de>
Date:   Tue Mar 20 13:07:05 2012 +0100

    drm/i915: Check VBIOS value for determining LVDS dual channel mode, too

All these checks predate this commit and have simply been overlooked.
Since we don't support switching between single-link and dual-link
modes anyway, this different checks could at best only get in the way
of refactorings, and in the worst case cause inconsistencies.

v2: Update the comment, we now have a solid way to figure out whether
we need dual-link lvds or not (falling back to vbt values as a last
resort). We still don't know how to switch between dual-link and
single link so leave that part intact. I'm not sure though whether
switching between these two modes makes any sense - we always drive
the panel at its fixed mode (with a fixed bpc) anyway ...
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently we have two encoder specific bits in the common mode_set
functions:
- lvds pin pair enabling
- dp m/n setting and computation

Now the lvds stuff needs to happen before the pll is enabled. Since
that is done in the crtc_mode_set functions, we need to add a new
callback to be able to move them to the encoder code (where they
belong). The dp m/n stuff is a giant mess anyway (since it also
confuses itself with the fdi link m/n handling), so that needs to be
handled separately.

I think that we can move the pll enabling down quite a bit, which
might allow us to eventually merge encoder->pre_enable with this new
pre_pll_enable callback. But for now this will allow us to clean
things up a bit.

Note that vlv doesn't support lvds, hence we don't need to change
anything in there.

v2: Fixup commit message, both suggested from Paulo Zanoni.
- dp m/n doesn't need to happen before pll enabling
- lvds doesn't exist on vlv, hence no changes required in the vlv pll
  function.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As per Chris Wilson's suggestion make
i915_gem_execbuffer_wait_for_flips() go away.

This was used to stall the GPU ring while there are pending
page flips involving the relevant BO. Ie. while the BO is still
being scanned out by the display controller.

The recommended alternative is to use the page flip events to
wait for the page flips to fully complete before reusing the BO
of the old front buffer. Or use more buffers.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NKristian Høgsberg <krh@bitplanet.net>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: don't remove obj->pending_flips, still required due to
reorder patches.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There seem to be indeed some awkwards machines around, mostly those
without OpRegion support, where the firmware changes the display hw
state behind our backs when closing the lid.

This force-restore logic has been originally introduced in

commit c1c7af60
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Thu Sep 10 15:28:03 2009 -0700

    drm/i915: force mode set at lid open time

but after the modeset-rework we've disabled it in the vain hope that
it's no longer required:

commit 3b7a89fc
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Mon Sep 17 22:27:21 2012 +0200

    drm/i915: fix OOPS in lid_notify

Alas, no.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54677
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=57434Tested-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Rebased.
Signed-off-by: NRob Clark <rob@ti.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v1)
[danvet: Pimp commit message a bit.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NRob Clark <rob@ti.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This goes on a separate patch since it won't apply on the stable
trees and there's nothing using panel fitter on HSW on the older
Kernels.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I actually found this problem on Haswell, but then discovered Ivy
Bridge also has it by reading the spec.

I don't have the hardware to test this.

Cc: stable@vger.kernel.org
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

DDI A and E have 4 lanes to share, so if DDI A is using 4 lanes,
there's nothing left for DDI E, which means there's no CRT port on the
machine.

The bit we're checking here is programmed at system boot and it cannot
be changed afterwards, so we cannot change the amount of lanes
reserved for each DDI port.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function runs on Haswell, so set the correct pch_transcoder and
cpu_transcoder variables. This fixes an assertion failure on Haswell
VGA.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is a full revert of 59c859d6:
    drm/i915: account for only one PCH receiver on Haswell

Now that the PCH code is fixed to be able use the only PCH transcoder
independently of the pipe and CPU transcoder, we can revert this.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Resolve conflict due to the rebasing of dinq on top of
drm-next.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we accumulate unpin tasks because we are pageflipping faster than the
system can schedule its workers, we can effectively create a
pin-leak. The solution taken here is to limit the number of unpin tasks
we have per-crtc and to flush those outstanding tasks if we accumulate
too many. This should prevent any jitter in the normal case, and also
prevent the hang if we should run too fast.

Note: It is important that we switch from the system workqueue to our
own dev_priv->wq since all work items on that queue are guaranteed to
only need the dev->struct_mutex and not any modeset resources. For
otherwise if we have a work item ahead in the queue which needs the
modeset lock (like the output detect work used by both polling or
hpd), this work and so the unpin work will never execute since the
pageflip code already holds that lock. Unfortunately there's no
lockdep support for this scenario in the workqueue code.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46991Reported-and-tested-by: NTvrtko Ursulin <tvrtko.ursulin@onelan.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Added note about workqueu deadlock.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56337Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Jani Nikula noticed that the parentheses are wrong and we & the bit
with the register address instead of the read-back value. He sent a
patch to correct that.

On second look, we write the same register in the previous line, and
the w/a seems to be to set FDI_RX_PHASE_SYNC_POINTER_OVR to enable the
logic, then keep always set FDI_RX_PHASE_SYNC_POINTER_OVR and toggle
FDI_RX_PHASE_SYNC_POINTER_EN before/after enabling the pc transcoder.

So the right things seems to be to simply kill the 2nd write.

Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Dropped a bogus ~ from the commit message that somehow crept
in.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

After the rework, intel_set_mode() became a little better behaved in
restoring the current mode if we failed to apply the requested modeline.
However, the failure path for load-detect would clobber the existing
state, leading to an oops during BIOS takeover on older machines.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the stricter checks introduced in
commit ac911edae5960d7dccd9883f5fa5d25b591520de
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date:   Wed Oct 31 17:50:19 2012 +0200

    drm/i915: Check the framebuffer offset

(and friends), it became especially prudent to make sure that the
additional fields inside the mode were cleared before attempting to
create a framebuffer. In particular, the fb created for load detection
failed to do so and hence failed.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This covers the "Disable FDI" section from the CRT mode set sequence.
This disables the FDI receiver and also the FDI pll.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This commit makes hsw_fdi_link_train responsible for implementing
everything described in the "Enable and train FDI" section from the
Hawell CRT mode set sequence documentation. We completely rewrite
hsw_fdi_link_train to match the documentation and we also call it in
the right place.

This patch was initially sent as a series of tiny patches fixing every
little problem of the function, but since there were too many patches
fixing the same function it got a little difficult to get the "big
picture" of how the function would be in the end, so here we amended
all the patches into a single big patch fixing the whole function.

Problems we fixed:

  1 - Train Haswell FDI at the right time.

    We need to train the FDI before enabling the pipes and planes, so
    we're moving the call from lpt_pch_enable to haswell_crtc_enable
    directly.

    We are also removing ironlake_fdi_pll_enable since the PLL
    enablement on Haswell is completely different and is also done
    during the link training steps.

  2 - Use the right FDI_RX_CTL register on Haswell

    There is only one PCH transcoder, so it's always _FDI_RXA_CTL.
    Using "pipe" here is wrong.

  3 - Don't rely on DDI_BUF_CTL previous values

    Just set the bits we want, everything else is zero. Also
    POSTING_READ the register before sleeping.

  4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train

    According to the mode set sequence documentation, this is the
    right place. According to the FDI_RX_TUSIZE register description,
    this is the value we should set.

    Also remove the code that sets this register from the old
    location: lpt_pch_enable.

  5 - Properly program FDI_RX_MISC pwrdn lane values on HSW

  6 - Wait only 35us for the FDI link training

    First we wait 30us for the FDI receiver lane calibration, then we
    wait 5us for the FDI auto training time.

  7 - Remove an useless indentation level on hsw_fdi_link_train

    We already "break" when the link training succeeds.

  8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE

    When we fail the training.

  9 - Change Haswell FDI link training error messages

    We shouldn't call DRM_ERROR when still looping through voltage
    levels since this is expected and not really a failure. So in this
    commit we adjust the error path to only DRM_ERROR when we really
    fail after trying everything.

    While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since
    it's what we use everywhere.

  10 - Try each voltage twice at hsw_fdi_link_train

    Now with Daniel Vetter's suggestion to use "/2" instead of ">>1".
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Applied tiny bikesheds:
- mention in comment that we test each voltage/emphasis level twice
- realing arguments of the only untouched reg write, it spilled over
  the 80 char limit ...]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to set the timing override chicken bit after fdi link training
has completed and before we enable the transcoder. We also have to
clear that bit again after disabling the pch transcoder.

See "Graphics BSpec: vol4g North Display Engine Registers [IVB],
Display Mode Set Sequence" and "Graphics BSpec: vol4h South Display
Engine Registers [CPT, PPT], South Display Engine Transcoder and FDI
Control, Transcoder Debug and DFT, TRANS_CHICKEN_2" bit 31:

"Workaround : Enable the override prior to enabling the transcoder.
Disable the override after disabling the transcoder."

While at it, use the _PIPE macro for the other TRANS_DP register.

v2: Keep the w/a as-is, but kill the original (but wrongly placed)
workaround introduced in

commit 3bcf603f
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Wed Jul 27 11:51:40 2011 -0700

    drm/i915: apply timing generator bug workaround on CPT and PPT

and

commit d4270e57
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Tue Oct 11 10:43:02 2011 -0700

    drm/i915: export a CPT mode set verification function

Note that this old code has unconditionally set the w/a, which might
explain why fdi link training sometimes silently fails, and especially
why the auto-train did not seem to work properly.

v3: Paulo Zanoni pointed out that this workaround is also required on
the LPT PCH. And Arthur Ranyan confirmed that this workaround is
requierd for all ports on the pch, not just DP: The important part
is that the bit is set whenever the pch transcoder is enabled, and
that it is _not_ set while the fdi link is trained. It is also
important that the pch transcoder is fully disabled, i.e. we have to
wait for bit 30 to clear before clearing the w/a bit.

Hence move to workaround into enable/disable_transcoder, where the pch
transcoder gets enabled/disabled.

v4: Whitespace changes dropped.

v5: Don't run the w/a on IBX, we only need it on CPT/PPT and LPT.

v6:
- resolve conflicts with Paulo's big hsw vga rework
- s/!IBX/CPT since hsw paths are now all separate, and Paulo's patch
  to implement the equivalent w/a for LPT is already merged.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v5)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v5)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

They are all written for a specific north disaplay->pch combination.
So stop pretending otherwise.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This essentially reverts

commit cb0953d7
Author: Adam Jackson <ajax@redhat.com>
Date:   Fri Jul 16 14:46:29 2010 -0400

    drm/i915: Initialize LVDS and eDP outputs before anything else

simply because it doesn't scale: It misses SDVO and DVO panels,
and now with DDI encoders on haswell this is becoming unmanageable.

Instead we simply sort the connector list after everything is
set up.
Reviewed-by: NAdam Jackson <ajax@redhat.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On Haswell/LPT we must disable the PCH transcoder before we disable
the FDI, so don't check for disabled FDI there.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function is only for the previous gens.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These workarounds are documented on the CRT mode set sequence.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... instead of "pipe", which is wrong.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... instead of PIPECONF_INTERLACE_MASK.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: applied the change by hand due to patch reorder.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

That function is made for IBX. Running it on LPT will trigger tons of
"unclaimed register" errors. The only port remaining on LPT is
PCH_ADPA.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because we already set all the bits we can set.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: apply by hand due to dropped patch. Also, obey my OCD a bit
and do a s/_TRANSACONF/TRANSCONF(TRANSCODER_A)/, makes it more
consisten with other lpt pch code imnsho ...]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... instead of using "pipe". As already explained in previous commits,
since Haswell/LPT cpu_transcoder, pch_transcoder and pipe are not the
same thing.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These asserts are specific to IBX/CPT/PPT. Inside the assert_pch_pll
function we even "return" in case we detect LPT, but I prefer to just
not call it. In the future we might rename to something like
ibx_assert_pch_pll.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since now we have lpt_enable_pch_transcoder.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For now the new functions are just copies. Differences will be added
later.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To ironlake_{en,dis}able_pch_transcoder since these functions will be
different on Haswell/LPT and since the "transcoder" they {en,dis}able
is on the PCH.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: again a small conflict because the fdi disable sequenc looks
a bit different here.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On Haswell/LPT, pipe, cpu_transcoder and pch_transcoder are different
things with different values, unlinke the previous gens. So here we
use the right thing at the right place.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: apply the patch by hand due to the reorder patch sequence. We
also can't kill all uses of pipe where we should, since the fdi link
train code isn't fixed up yet on this baselin.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is no LVDS, so don't poke the LVDS registers.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is just wrong. The lpt_program_iclkip should disable the PCH
pixel clocks (and yes, we plan to rename it later).
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>