The controller on the docg4 has a "reliable" mode, where consecutive 2k pages
are used in parallel.  The initial program loader (IPL) on my Treo 680 expects
the secondary program loader (SPL) to be written in this mode.  This patch adds
support for writing data in reliable mode, by way of a module parameter.
Support for reading in this mode (as the IPL does) is not supported yet, but
alternate (even-numbered) 2k pages written in reliable mode can be read normally
(odd-numbered pages will contain junk and generate ecc errors).
Signed-off-by: NMike Dunn <mikedunn@newsguy.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The cmdline is the easiest to change source of information. Thus
let it take precedence over 'RedBoot' and 'ofpart'. This makes the
mxc_nand driver to be in sync with all other NAND drivers that support
'cmdlinepart' partition parsing.

Also change 'const char *' to 'const char const *' as advised by checkpatch.pl
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

If nand_scan_ident() or nand_scan_tail() fails, the NAND chip may have
been deselected and the clock already disabled. Thus, check 'clk_act'
in the error path to decide whether the clock still needs to be
disabled.

This fixes a:
|WARNING: at drivers/clk/clk.c:472 __clk_disable+0x3c/0x78()
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

It's more user friendly to report debug information and statistics
through debugfs, than to use printing facilites.

This patch introduces a very minimal debugfs infrastructure
and moves eraseblock wear report to an entry located at:

/sys/kernel/debug/nandsim/wear_report

This means we can remove rptwear option and just let
the user get the wear report when we needs to.
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

This patch solves a NULL pointer dereference, this may occur if the tuple
is not mappable (jumps to continue in the for-loop). Out of the loop
possible results are:
- info->list_size == 0  if no of the tuples is mappable
- info->list_size == 1
- info->list_size > 1
If no one of the supplied tuples is mappable (info->list_size == 0) and
info->cmtd will not be set. But it is used in mtd_device_parse_register, OOPS!
actually it should generate an error in this case!
Signed-off-by: NAnton Prins <anton.prins@nl.bosch.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

If we set oobdelta to zero then we will either return -EINVAL or hit
a divide (modulus) by zero on the next line when we check
"(ooblen % oobdelta)".  It's better to just return -EINVAL here instead.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

fix: do block-buffer initialize for the whole next page to zero.
Signed-off-by: NChristian Herzig <christian.herzig@keymile.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

This patch fix pmecc's read_page() to return maximum number of bitflips, 0 if uncorrectable.

In the commit: 3f91e94f ("mtd: nand: read_page() returns max_bitflips ()"),
The ecc.read_page() is changed to return the maximum number of bitflips.
And when meet uncorrectable bitflips it needs to return 0.

See the comment in nand.h:
 * @read_page:	function to read a page according to the ECC generator
 *		requirements; returns maximum number of bitflips corrected in
 *		any single ECC step, 0 if bitflips uncorrectable, -EIO hw error
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Reviewed-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

When working on a problem with some flash chips that lock up during
write-buffer operations, I think there may be a bug in the linux
handling of chips using cfi_cmdset_0002.c.

The datasheets I have found for a number of these chips all specify that
when aborting a write-buffer command, it is not enough to use the
standard reset.  Rather a "write-to-buffer-reset command" is needed.
This command is quite similar for all chips, the main variance seem to
be if the final 0xF0 can go to any address or must go to addr_unlock1.

The bug is then in the recovery handling when timing out at the end of
do_write_buffer, where using the normal reset command is not sufficient.

Without this change, if the write-buffer command fails then any
following operations on the flash also fail.
Signed-off-by: NHarald Nordgard-Hansen <hhansen@pvv.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

- NAND_CMD_READID want an address that it is not scaled on x16 device (it is always 0x20)
- NAND_CMD_PARAM want 8 bits data
Signed-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The driver call nand_scan_ident in 8 bit mode, then
readid or onfi detection are done (and detect bus width).
The driver should update its bus width before calling nand_scan_tail.

This work because readid and onfi are read work 8 byte mode.

Note that nand_scan_ident send command (NAND_CMD_RESET, NAND_CMD_READID, NAND_CMD_PARAM), address and read data
The ONFI specificication is not very clear for x16 device if high byte of address should be driven to 0,
but according to [1] it should be ok to not drive it during autodetection.

[1]
3.3.2. Target Initialization

[...]
The Read ID and Read Parameter Page commands only use the lower 8-bits of the data bus.
The host shall not issue commands that use a word data width on x16 devices until the host
determines the device supports a 16-bit data bus width in the parameter page.
Signed-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

This help to detect bad flash identification in case the size is not present
on the name (ONFI).
Signed-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

nand_wait_ready timeout should not assume HZ=100.
Make it independent of HZ value by using msecs_to_jiffies.
Signed-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

There are two reasons to remove the "chip" parameter in nand_get_device():

[1] The nand_release_device() does not have the "chip" parameter.
[2] We can get the nand_chip by the mtd->priv field.

This patch removes the "chip" parameter in nand_get_device().
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The nand_get_device() does not select the chip, but nand_release_device()
does de-select the chip. It is really strange.

With the current code, nand_sync() will de-select the chip, even if the chip
has never been selected.

To make the balance of select/de-select chip, it's better to remove the
de-select chip code in nand_release_device() which makes the code more
clear.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Micron N25Q128 has two types of flash:

 - One is for 1.8v supply voltage, prefixed with "n25q128a11" and the jedec
   code is 0x20bb18.

 - Another is for 3v supply voltage, prefixed with "n25q128a13" and the jedec
   code is 0x20ba18.

So modify the original type info and add another type for Micron N25Q128.
Signed-off-by: NLiming Wang <walimisdev@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Loading cs553x_nand with Hynix H27U1G8F2BTR NAND flash causes this bug:

kernel BUG at drivers/mtd/nand/nand_base.c:3345!
invalid opcode: 0000 [#1]
Modules linked in: cs553x_nand(+) vfat fat usb_storage ehci_hcd usbcore usb_comr
Pid: 436, comm: modprobe Not tainted 3.6.7 #1
EIP: 0060:[<c118d205>] EFLAGS: 00010296 CPU: 0
EIP is at nand_scan_tail+0x64c/0x69c
EAX: 00000034 EBX: cea6ed98 ECX: 00000000 EDX: 00000000
ESI: cea6ec00 EDI: cea6ec00 EBP: 20000000 ESP: cdd17e48
 DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
CR0: 8005003b CR2: 0804e119 CR3: 0d850000 CR4: 00000090
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Process modprobe (pid: 436, ti=cdd16000 task=cdd1c320 task.ti=cdd16000)
Stack:
 c12e962c c118f7ef 00000003 cea6ed98 d014b25c 20000000 fffff007 00000001
 00000000 cdd53b00 d014b000 c1001021 cdd53b00 d01493c0 cdd53b00 cdd53b00
 d01493c0 c1047f83 d014b4a0 00000000 cdd17f9c ce4be454 cdd17f48 cdd1c320
Call Trace:
 [<c118f7ef>] ? nand_scan+0x1b/0x4d
 [<d014b25c>] ? init_module+0x25c/0x2de [cs553x_nand]
 [<d014b000>] ? 0xd014afff
 [<c1001021>] ? do_one_initcall+0x21/0x111
 [<c1047f83>] ? sys_init_module+0xe4/0x1261
 [<c1031207>] ? task_work_run+0x36/0x43
 [<c1265ced>] ? syscall_call+0x7/0xb
Code: fa ff ff c7 86 d8 00 00 00 01 00 00 00 e9 5f fc ff ff 68 f8 26 2e c1 e8 a7
EIP: [<c118d205>] nand_scan_tail+0x64c/0x69c SS:ESP 0068:cdd17e48

Initialising ecc.strength before the call to nand_scan() fixes this.
Signed-off-by: NNathan Williams <nathan@traverse.com.au>
Cc: stable@vger.kernel.org [3.4+]
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Acked-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

While checking the "__devinit" removal patches with checkpatch.pl, I
noticed several warnings related to a space between the function name
and '(', as well as long lines. I fixed the warnings up in this patch.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The kernel has never contained the symbol SA1100_FORTUNET so the driver
never compiled and can be removed safely.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The mtd partition command line parser already supports a "lk" option to mask
MTD_POWERUP_LOCK. This extends that same functionality to device tree
partition specifications.
Signed-off-by: NJosh Radel <jradel@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

BCMA bus can contain NAND flash memory, it's registered in system as
platform device. This adds required hooks and place for controler
specific drivers.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

This is required by NAND flash driver for initializing wait counters.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Use ll to be able to remove the casts.
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The line belongs above the comment, not below it.
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The CFE does not use 4K sectors even if the flash supports it, so
for the fixed partitions like CFE itself or NVRAM the erase block
size is always 64k or bigger.
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The length of the spare part is calculated the same way in both branches
so move to a common place.
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

namelen is never used, so drop it.
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>